MANUAL ENGLISH EDGE EBS-1 V2 Order code: D1476B Highlite International B.V.
EDGE EBS-1 Table of contents Warning ...............................................................................................................................................................................2 Safety Instructions ......................................................................................................................................................2 Operating Determinations......................................................................................................
EDGE EBS-1 Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials.
EDGE EBS-1 IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device. Before using the device, check the regulations regarding the frequency allocation in your country or region. ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Never use the device during thunderstorms, unplug the device immediately. Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.
EDGE EBS-1 Operating Determinations ● ● ● ● ● This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. The maximum ambient temperature ta = 40 °C must never be exceeded. The relative humidity must not exceed 50 % with an ambient temperature of 40 °C. If this device is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
EDGE EBS-1 Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.com and request an RMA prior to shipping the fixture.
EDGE EBS-1 Description of the Device The EDGE EBS-1 is a wireless beltpack system. The set comes with a beltpack transmitter, a receiver, and a headset. The EBS-1 is suitable for both vocal and instrumental applications and can be used only with guitars with an active pickup. The transmitter is powered by two AA 1,5 V batteries (not included).
EDGE EBS-1 Overview Transmitter (Front/Back) Fig. 01 01) 02) 03) 04) 05) 06) Antenna OLED display Power button DOWN button UP button Belt clip Transmitter (Top/Bottom) Fig.
EDGE EBS-1 Receiver (Front) Fig. 03 12) LCD display 13) Control Turn/press this control to select, adjust and confirm the main menu options. 14) Return button 15) IR sensor 16) Power button Press and hold down this button for 2 seconds to switch the device on/off. Receiver (Back) Fig.
EDGE EBS-1 Mounting – Multiple Receivers Step 1 Fig. 06 Step 2 Fig. 07 Step 3 Fig.
EDGE EBS-1 Setup Examples 4 x EDGE EHS-1 Fig.
EDGE EBS-1 8 x EDGE EHS-1 Fig.
EDGE EBS-1 Setup and Operation Follow the directions below, as they pertain to your preferred operation mode. Before using the device, check the regulations regarding the frequency allocation in your country or region. Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Receiver Setup 01) Connect the supplied power adapter to the DC power connector (24) on the rear of the receiver. 02) Plug the power adapter into a power outlet.
EDGE EBS-1 Transmitter Setup Install the beltpack on your belt by means of the belt clip (06). Example 1 – Headset Fig. 12 Example 2 – Electric Guitar Fig. 13 Belt Clip Orientation Fig. 14 For best performance and comfort, you can mount the belt clip in 2 different ways. The best results can be reached with the antenna pointing upwards.
EDGE EBS-1 Control Panel A) Antenna signal B) AF signal mute C) Receiver lock D) Transmitter battery status E) Group (A–J) F) Channel (1–14) G) Receiver frequency H) Squelch I) Device name J) User color K) High-pass filter status L) AF signal strength M) Wireless signal strength Fig. 15 Inserting the Batteries Fig. 16 01) Open the battery housing (10). 02) Insert the batteries into the battery housing (10). The transmitter operates with two AA 1,5 V batteries.
EDGE EBS-1 Compensation of Interference with Balanced Connections Main Menu Options 01) Upon start-up, the display will show the DAP Audio logo. After 2 seconds, the display will show the current device status. 02) Press the control (13) to open the main menu.
EDGE EBS-1 ● ● ● ● ● ● ● ● ● ● SYNC LOCK TX GAIN RX GAIN LOW CUT SQUELCH TONE KEY COLOR NAME ANT DC 04) Press the control (13) to open the desired menu. 1. Group In this menu you can set the desired group. Each group (A–J) has a unique set of channels with 14 fixed frequencies per channel. See the table on page 17. 01) Turn the control (13) until the display shows: 02) Press the control (13) to edit. 03) Turn the control (13) to select the desired group. The adjustment range is A–J.
EDGE EBS-1 A [1]:606.000MHz [2]:608.025MHz [3]:610.325MHz [4]:612.900MHz [5]:615.750MHz [6]:618.875MHz [7]:622.275MHz [8]:626.050MHz [9]:631.200MHz [10]:639.475MHz [11]:645.175MHz [12]:653.175MHz [13]:663.750MHz [14]:667.800MHz B [1]:606.200MHz [2]:608.225MHz [3]:610.525MHz [4]:613.100MHz [5]:615.950MHz [6]:619.075MHz [7]:622.475MHz [8]:626.250MHz [9]:631.400MHz [10]:639.675MHz [11]:645.375MHz [12]:653.375MHz [13]:663.950MHz [14]:668.000MHz C [1]:606.225MHz [2]:607.250MHz [3]:608.475MHz [4]:609.
EDGE EBS-1 4. Scan In this menu you can automatically scan the entire frequency range, in order to find and choose the unused frequency. By doing so, you can avoid signal distortion. 01) Turn the control (13) until the display shows: 02) Press the control (13) to enter. The display will show: 03) The device will now automatically scan the entire frequency range (606–668 MHz). This process may take up to 2 minutes. 04) Once the scanning is finished, turn the control (13) to select the desired frequency.
EDGE EBS-1 6. Lock In this menu you can lock the receiver’s display. 01) Turn the control (13) until the display shows: 02) 03) 04) 05) 06) Press the control (13) to edit. Turn the control (13) to select ON or OFF. Press the control (13) to confirm. If you have chosen ON, the display will be locked. In order to unlock the display, press and hold down the control (13) for 4 seconds, until the receiver lock symbol disappears (see C, Fig. 15, page 14). 7.
EDGE EBS-1 9. Low Cut In this menu you can set the high-pass filter. The high-pass filter removes low frequency signals picked up by the transmitter. 01) Turn the control (13) until the display shows: 02) Press the control (13) to edit. 03) Turn the control (13) to select ON or OFF. 04) Press the control (13) to confirm. 10. Squelch In this menu you can set the squelch threshold. It eliminates the noise resulting from momentary spikes in the output when turning the transmitter off.
EDGE EBS-1 12. Color In this menu you can set the receiver’s color. It is useful when working with multiple receivers and transmitters. 01) Turn the control (13) until the display shows: 02) Press the control (13) to edit. 03) Turn the control (13) to select one of the 8 colors (red, yellow, green, blue, orange, brown, white, black). 04) Press the control (13) to confirm. 13. Name In this menu you can set the receiver’s name. A name can consist of up to 8 characters.
EDGE EBS-1 14. Ant Dc In this menu you can set the antenna input/output power supply. 01) Turn the control (13) until the display shows: 02) Press the control (13) to edit. 03) Turn the control (13) to select ON or OFF. 04) Press the control (13) to confirm. ● ● If the input power comes from the power adapter: the “ANT DC: On” will power the active antenna via the BNC antenna connectors (20/25). If the input power comes from the antenna distributor: the “ANT DC: On” will power the receiver.
EDGE EBS-1 Transmitter 01) Press and hold down the power button (03) for 2 seconds to switch the transmitter ON/OFF. 02) Upon start-up, the display will show the following splash screen: Mute 01) Move the mute switch (07) to ON, to mute the transmitter. 02) Move the mute switch (07) to MUTE, to deactivate mute. Lock 01) Move the lock switch (11) to LOCK, to lock the transmitter. When the lock is on, it is not possible to adjust the device’s settings.
EDGE EBS-1 05) Press the power button (03) to save changes. The display will show: 06) Press the UP/DOWN buttons (04/05) to set the desired RF power. Select one of the 3 options: ● LOW (10 mW) ● MID (20 mW) ● HIGH (30 mW) 07) Press the power button (03) to save changes. The display will now show the splash screen. Note: The maximum allowed RF output is 10 mW. The use of outputs stronger than 10 mW must be permitted by the local authorities.
EDGE EBS-1 Connection Cables Take care of your cables, always holding them by the connectors and avoiding knots and twists when coiling them: This gives the advantage of increasing their life and reliability. Periodically check your cables. A great number of problems (faulty contacts, ground hum, discharges, etc.) are caused entirely by using unsuitable or faulty cables.
EDGE EBS-1 Maintenance The DAP Audio EDGE EBS-1 requires almost no maintenance. However, you should keep the unit clean. Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. Do not use alcohol or solvents. Keep connections clean. Disconnect electric power, and then wipe the audio connections with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
EDGE EBS-1 Approval The DAP Audio EDGE EBS-1 is a Class 2 wireless audio device (Commission Decision 2000/299/EC). Frequency range: 606–668 MHz BE BG CZ DK DE EE IE EL ES FR HR IT CY LV LT LU HU MT NL AT PL PT RO SI SK FI SE UK Exclusion of liability The frequency ranges available for wireless microphones differ per country and region. Consult the respective national and/or regional authorities as licensing or specific restrictions may apply for the use of the device.
EDGE EBS-1 Spectrum authorities in the EFTA countries: Iceland Post and Telecom Administration Liechtenstein Amt für Kommunikation Norway Norwegian Communications Authority Switzerland Federal Office of Communications Spectrum authorities in the EU candidate countries: Montenegro Agency for Electronic Communications and Postal Services Republic of North Agency for Electronic Communications Macedonia Albania Electronic and Postal Communications Authority Serbia Regulatory Agency for Electronic Communications
EDGE EBS-1 Dimensions Order code: D1476B 29
EDGE EBS-1 Order code: D1476B 30
©2020 DAP Audio