V3-BTZBE danalock V3-BTZBE Technical Manual Version 2.3, February 2019 Danalock V3-BTZBE, Technical Manual v.2.
V3-BTZBE Content Content .......................................................................................................... 2 Related Information .......................................................................................................... 6 Safety first...................................................................................................... 6 Simple Guidelines ............................................................................................................
V3-BTZBE Corporate Office Poly-Control ApS Gammel Stillingvej 427 C DK – 8462 Harlev J Denmark. www.poly-control.com Copyright and Trademarks © Poly-Control ApS. All rights reserved. Poly-Control, the danalock logo and danalock are trademarks of Poly-Control ApS, registered in the United States and in other countries. All other trademarks are the property of their respective owners. Release Notice This document is release 2.3 of the V3-BTZBE, Technical Manual.
V3-BTZBE No Poly-control employee, agent or dealer is authorized to modify, extend or complete the present guarantee in any way.
V3-BTZBE MIC (Japan) The device complies with the Japanese Ordinance concerning Technical Regulations Conformity Certification etc. of Specified Radio Equipment Article 2 clause (1) Item (19) for radio terminal equipment supporting Bluetooth Low Energy 2400-2483.5 MHz and Zigbee 2400-2483.5 MHz.
V3-BTZBE Introduction This document contains the installation guide for the Danalock product type series V3BTZBE units. This manual is intended for use by system integrators, service providers and application developers (collectively, “Resellers”). It is not intended for end-users of the V3BTZBE. Any end-user documentation is to be prepared and furnished by the Resellers. This manual describes how to set up, configure, install, operate, and troubleshoot the product.
V3-BTZBEE Qualified Service Except for batteries, the V3-BTZBE contains no user serviceable or replaceable parts. Non-functioning units must be returned to an authorized service center for repair or replacement. Accessories and Batteries Use only approved accessories or batteries. Do not connect incompatible products. There is risk of explosion or fire if an incorrect type replacement battery contacts are shorted.
V3-BTZBEE Security for electrical manipulation The V3-BTZBE is tested compliance to the EMC requirement laid out in the 1999/05/EC directive. The performance hereof ensures correct operation in the presence of electromagnetic interference and/or electrostatic discharge. EN 14846 security – electrical manipulation classification grade=3. Children The V3-BTZBE series and its accessories are not used to solicit data from or market to children.
V3-BTZBEE The V3-BTZBE unit cannot be turned off after installation, so any doors installed with the V3-BTZBE etc. must not operate near health care facilities when any regulations posted in these areas prohibit the use of wireless phones or two-way radios. Hospitals and health care facilities may be using equipment that could be sensitive to external RF energy. Potentially Explosive Atmospheres The V3-BTZBE unit cannot be turned off after installation, so any building installed with V3-BTZBE etc.
V3-BTZBEE Privacy policy Danalock App privacy policy This privacy policy governs your use of the software application ”danalock App” for mobile devices that is created by Poly-Control ApS. The Application controls the use of the electronic door locking device Danalock, and only works with iPhone 4s / Android 4,4 or newer smartphones with Bluetooth LE or Zigbee technology. User Provided Information The Application obtains the information you provide when you download and register the Application.
V3-BTZBEE Your Consent By using the Application, you are consenting to our processing of your information as set forth in this Privacy Policy now and as amended by us. "Processing,” means using cookies on a computer/hand held device or using or touching information in any way, including, but not limited to, collecting, storing, deleting, using, combining and disclosing information, all of which activities will take place in Scandinavia, Europe, Middle East, Asia and United States.
V3-BTZBEE Installing the unit Practical installation advice Please follow the installation guide carefully. It is available on the danalock site that is found at https://guide.danalock.com/: Be aware that multiple installation guides exist. The installation guides are targeted for the specific models. Danalock V3-BTZBE, Technical Manual v.2.
V3-BTZBEE Functionality check LED signals The V3 series is fitted with a LED that has the following status indications: Status LED mode ! ! ! ! LED color Status indication Constant blue till finishes then one green blink Lock calibration Constant red light till finishes Manually lock/unlock when not calibrated Constant yellow light till finishes Lock has been latched successfully Constant yellow till fails then one red blink Lock failed during latch Constant green light till finishes Lock has
V3-BTZBEE Error Error description Possible solutions Grey key in keychain The key in the keychain turns grey when the lock is unreachable 1. 2. 3. 4. Lock cannot be added to the gateway The lock cannot be added to the gateway 1. Exclude the lock from the gateway 2. Re-include the lock to the gateway Auto unlock stopped working Auto unlock stopped working because other devices have been paired 1. Turn off Bluetooth on the phone 2.
V3-BTZBEE Product family The V3 series covers the following models that are classified within the respective region depending on the frequencies that are used for the models. Model V3-BT V3-BTZBE V3-BTZ-E V3-BTZ-U V3-BTZ-H Bluetooth Zigbee X X X X X EU Z-Wave US H Apple Home Kit X X X X X Accessories The following accessories are available for the V3 series.
V3-BTZBEE Technical Assistance If you have a problem and cannot find the information you need in the product documentation, please contact Poly-Control ApS Poly-Control ApS Gammel Stillingvej 427 C DK – 8462 Harlev J Denmark Tel: +45 42 42 81 22 E-mail: support@danalock.com Web: www.danalock.
V3-BTZBE Specifications Product specifications The V3-BTZBE unit is with integrated antennas and battery Connections Operational voltage (supply voltage): Standby time on the battery 4 x 3V DC (12V DC) 450 days for V3-BTZBE models Temperature range In active running mode Storage -20ºC to +40ºC 5ºC to +50ºC Mechanical specifications Dimensions: Width: Height: 59 mm 59 mm Weight: Excl. batteries Incl. batteries 130 g 195 g Danalock V3-BTZBE, Technical Manual v.2.
V3-BTZBE Approvals and certificates The V3-BTZBE product is certified according to the following radio recommendations (EU, US/Canada and Japan respectively): FCC ID: 2ADSH-V3BTZBE IC: 12588A-V3BTZBE Battery: CR123A 3V 2.4 GHz, Pout < 20 mW xxx-xxxxxx The V3-BTZBE is certified for electromechanically operated locks and striking plate’s classification matrix (N/A is not applicable for V3-BTZBE): FCC and IC Statements The device contains radio transmitters that comply with CFR 47 Part 15.
V3-BTZBE (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. NOTICE statements according to CFR 47 Part 15.21: Changes or modifications made to this equipment not expressly approved by Poly-Control ApS may void the FCC authorization to operate this equipment. Statements according to CFR 47 Part 2.
V3-BTZBE The device complies with the requirements of the 2012/19/EU directive on waste electrical and electronic equipment (WEEE). Including: EN 14846:2008 (EN/IEC 60950-1 + A11, A1, AC, A12 and A2):2013 Electromechanically operated locks and striking plates (Declaration) ITE Safety CE The V3-BTZBE product complies with the essential requirements of the RED Directive 2014/53/EU as stated by the EC Declaration of Conformity.