User's Manual

ManualsBrandsDamm Cellular Systems ManualsElectronicsDOOR SYSTEM-TX

TetraFlex

V7.5

US DRAFT version

Manual version 1.01

27.01.2012

The information contained in this document is the property of Damm Cellular Systems A/S. This document is

subject to copyright and shall not be published or reproduced, in whole or in part, without the written permission

of Damm Cellular Systems A/S.

Møllegade 68, DK-6400 Sønderborg, Denmark

Phone: +45 74 42 35 00, Fax: +45 74 42 30 31,

E-Mail: dcs@damm.dk,

Summary of content (90 pages)

PAGE 1
TetraFlex® V7.5 US DRAFT version Manual version 1.01 27.01.2012 The information contained in this document is the property of Damm Cellular Systems A/S. This document is subject to copyright and shall not be published or reproduced, in whole or in part, without the written permission of Damm Cellular Systems A/S. © 2010 Damm Cellular Systems A/S. All rights reserved. Møllegade 68, DK-6400 Sønderborg, Denmark Phone: +45 74 42 35 00, Fax: +45 74 42 30 31, E-Mail: dcs@damm.
PAGE 2
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Introduction http://www.damm.dk INTRODUCTION This manual is intended for installation and maintenance of BS4xx TetraFlex® Base Station, including additional units, installation software, and how to configure the system for operational use. Remark: TetraFlex® ver. 7.
PAGE 3
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - Introduction Indoor Base station models BS411 BS414 Max. 16 carriers Max. 8 carriers Max. 4 carriers Outdoor station BS421 + SB 421 Max.
PAGE 4
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Introduction The manual is divided into more sections which may be printed separately.
PAGE 5
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Reference documents RF Exposure The DAMM developed transmitting devices mentioned in this User Manual have the Nemko approval concerning “Maximum Permissible Exposure Calculations” which are the European limits for maximum permissible exposure defined in the document 1995/519/EC, Council Recommendation of 12. July 1999.
PAGE 6
Damm Cellular Systems A/S, Denmark TetraFlex® 7.5 Manual Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.
PAGE 7
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown TABLE OF CONTENTS Introduction ................................................................................................................................................ 2 Reference documents .................................................................................................................................. 5 TetraFlex® Manual breakdown ...............
PAGE 8
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 1.2.5.1 Single Carrier BS installation recommendation (1 x BS421) ............................................................... 1-19 1.2.5.2 Dual Carrier BS installation recommendation (2 x BS421) .................................................................. 1-19 1.2.6 Power connection to SB421 .......................................................................
PAGE 9
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 2.4.4 Installing individual parts of the TetraFlex packet. ................................................................................ 2-49 2.4.4.1 BSC....................................................................................................................................................... 2-49 2.4.4.2 Start Menu ..........................................
PAGE 10
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 2.7.9 Add a Power Supply ............................................................................................................................... 2-84 2.7.10 Combiner adjustment .......................................................................................................................... 2-84 2.7.11 Antenna measurement ..................................
PAGE 11
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 2.13.6.2 Bringing the API to work on your system: .......................................................................................2-123 2.13.6.2.1 In the subscriber register: ............................................................................................................2-123 2.13.6.2.2 In the Application (Dispatcher) folder:............................
PAGE 12
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 2.16.10.2.1 Routing multicast: ......................................................................................................................2-161 2.16.10.2.2 Group management in multicast: ..............................................................................................2-161 2.16.11 Applicable tools for router programming ............................
PAGE 13
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 3.3.5.2 Organization ........................................................................................................................................ 3-33 3.3.5.3 Profile .................................................................................................................................................. 3-35 3.3.5.4 Subscriber ........................
PAGE 14
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 3.5.9.1 Assigning subscribers to DGNA ........................................................................................................... 3-84 3.5.9.2 De-assigning subscribers to DGNA ...................................................................................................... 3-86 3.5.9.3 Showing DGNA history .............................................
PAGE 15
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 3.7.10.6 Voice GW .........................................................................................................................................3-116 3.7.10.7 PD-GW .............................................................................................................................................3-116 3.7.10.8 App-GW ...................................
PAGE 16
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - TetraFlex® Manual breakdown 4.6.3 +14V and +26V DC/DC converters ......................................................................................................... 4-27 4.6.4 Micro-controller ..................................................................................................................................... 4-27 PART-5: HARDWARE UNITS .........................................
PAGE 17
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Revision REVISION Software covered by this manual Software BSC Network Management Dispatcher Log Server / Log Client SW Version 7.52 7.52 7.52 7.52 Release date 30-09-2011 30-09-2011 30-09-2011 30-09-2011 Record of Manual Versions Numbers SW. 7.40 7.40 7.4 7.4 Ver. 2.00 2.01 2.02 2.03 Release Date 01-11-2009 11-01-2010 26-02-2010 30-03-2010 7.4 7.4 7.5 7.5 2.04 2.05 1.00 1.
PAGE 18
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Revision IMPORTANT: DAMM will execute great effort to maintain and update this manual so it will always be up to date regarding information and readability. To do this DAMM needs to get feedback from you. So if you as reader find anything which could be done better, items which is not dealt with, sections which is difficult understandable etc.
PAGE 19
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Abbreviations / Definitions ABBREVIATIONS / DEFINITIONS Short AIR API Application Date Application Date Limit. Application PC BS BSC BSC.
PAGE 20
Damm Cellular Systems A/S, Denmark PSTN PTT RAM Release Date. Release number SACCH SCCH SCK SDS SELV Site SLA SNMP Software package SSI Subscriber register TBD TEA1… TEI TETRA TetraOM ToIP TSI UDP User number UTP VoIP WAN Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Abbreviations / Definitions Public Switched Telephone Network Push To Talk Random Access Memory The date where DAMM releases the software.
PAGE 21
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 PART-1: Hardware Installation TetraFlex® 7.
PAGE 22
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 1.1 SB421 1.1.1 Environmental / climatic requirements The SB421 (Service Box) is designed for outdoor operation, in such a way that it can be placed in the antenna mast close to the Base station(s) The Service Box is designed to be able to operate at severe environmental conditions.
PAGE 23
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - SB421 1.1.4 SB421 basic elements 1.1.4.1 SB421 Variants Item no. SB421 Description 105102 General performance w/CF 105105 High performance with/CF Processor Celeron M 1.0GHz P4 Mobile 1.4GHz RAM Storage 512Mb 2GB CF 1 GB 8GB CF (2+2+4) Figure 1-1: SB421 Variants The above specifications are a minimum and may be changed according to availability of processors and storage media.
PAGE 24
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - SB421 In OM enter AP and the connection is established. Use for help menu and select PS421. . 1.1.4.4 BSC421 Base Station Controller Please refer to appropriate information in section 1.1.4.1 Regarding the type and specification of the CPU board (High performance or general performance dependent of the type of SB421) Figure 1-2: BSC421 1.1.4.4.
PAGE 25
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 1.1.4.4.3 BSC connections Connections o o o o o o o o TR1 and TR2 LAN to Interconnection board (J31) LAN / Wan to Interconnection board (J32) I/O for PS etc. (J30) USB1 for Node Dongle (J33) USB2 for service and maintenance (J50) VGA for service and maintenance (J51) LAN for service and maintenance (J52) CF socket (J201) 1.1.4.4.
PAGE 26
Damm Cellular Systems A/S, Denmark Unit Interconnection Board Battery BSC421 TR1 TR2 LAN/WAN Power Power Supply PS421 Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Placement Fuse Rating Fuse Size F101 F102 F113 F133 F153 10A Slow 1A Slow 3.15A Slow 3.15A Slow 1A Slow 5x20 5x20 5x20 5x20 5x20 F101 6.3A Slow 5x20 Figure 1-4: Fuse Listing 1.1.4.5 Interconnection Board 1.1.4.5.
PAGE 27
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 1.1.4.5.3 LED’s o o o o EXT SEC IN 2 EXT SEC IN 1 TR2 SEC IN TR1 SEC IN Figure 1-5: Interconnection Board 1.1.4.5.
PAGE 28
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 1.1.4.5.5 PS Connection to TR1 and TR2 o The blue wire of the BS shall be connected to the minus terminal o The black wire of the BS cable shall be connected to plus terminal. o The green / yellow wire of the SB421 cable shall be connected to the ground terminal. 1.1.4.5.6 LAN Connection to TR1 and TR2 Connect the following terminals: NOTE: Cable used must be 24AWG solid core.
PAGE 29
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - SB421 1.1.4.5.9 Redundant SB421 operation A second SB421 (BSC) may be configured for redundant operation both as 2 carriers and as 3 - 4 carriers. Note: A HW modification is needed for redundant and/or 3-4 carrier operation. See section 1.1.5 for further information. 1.1.4.5.9.1 LAN Connection Note: LAN in / out is used for redundant SB421.
PAGE 30
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 The 3 screw connection block for the 100-240V AC mains power Phase, Null and Ground is located on the inner left side of the SB421 housing. The 100-240V AC mains power connection shall be provided with an appropriate fuse according to the selected mains supply voltage as to ensure a consumption of 4,5A (110V) / 2A (230V).
PAGE 31
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 When delivered, the temperature sensor cable is terminated with a 4-pol modular connector. Please cut the connector and mount the wires in the LSA block of the LAN/WAN connection module according to this: SB421 J8A Pin# 1 2 3 4 Temperature Sensor Cable Function Color Gnd.
PAGE 32
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 NOTE: For change in the field, please order a change kit from DAMM. This kit includes a manual dealing with this issue, jumpers, screws, markings etc.
PAGE 33
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - SB421 1.1.6 SB421 Internal Battery Assembly 1.1.6.1 Battery kit maintenance The battery is specified to a life time of 3-5 years depending on the use and environment. It is recommended that the battery is checked at least every second year and exchanged if necessary. 1.1.6.1.1 Installing batteries 1.1.6.1.1.
PAGE 34
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 1.1.6.1.1.2 Installation Figure 1-12: Internal battery assembly o Install the “SB421 battery holder Lower” foam (pos.1) in the bottom of the SB421 casing. o Install the “SB421 battery holder Upper” foam (pos.2) in the front of the SB421 casing o Attach the blue wire of the battery cable (pos.J41) to the left terminal of a battery (pos.
PAGE 35
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - SB421 J40 Temperature switch Figure 1-13: Interconnection Module 1.1.7 External -48 battery kit (option) connection block The 3 screw connection block for -48V DC, 0 and ground is located on the inner right side of the SB421 housing. The SB421 is operated at -48V nominal DC (SELV) derived from the internal power supply. An internal or external battery pack may be connected for backup purposes.
PAGE 36
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Note: If an internal battery kit is mounted, pull out the battery connector J40 for the internal battery and insert the free connector for the external battery into J40 instead. If no internal battery kit is present, the external battery plug is inserted from factory. WARNING: Please observe polarity of the external battery leads.
PAGE 37
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 1.2 BS421 1.2.1 Environmental / climatic requirements The Base Station is designed for outdoor operation, such that it can be placed in the antenna mast close to the antennas. The Base Station is designed to be able to operate at severe environmental conditions. The Base station is guaranteed to operate under ambient air temperatures from –25°C to +55°C Celsius.
PAGE 38
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 1.2.4 BS421 main components Filter cover and filters removed.
PAGE 39
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 1.2.5 Attaching RX/TX antennas Before installing the Base Station please read the application note in this manual about the Antenna Systems. The following antenna cables shall be attached: 1.2.5.
PAGE 40
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - BS421 1.2.6 Power connection to SB421 Before starting on this task, please read the entire chapter carefully. RX/TX A RXB PS LAN GPS OUT A LAN / 1sec GND 0V - 48V Figure 1-18: Power connection The BS421 is operated at -48V nominal DC SELV (Safety Extra Low Voltage). The provision of power is done via the SB421 TR1/TR2 connection module.
PAGE 41
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 1.2.6.1 System Connector Use a LSA tool for the Ethernet connection Figure 1-19: System Connector Connect the following terminals: NOTE: Cable used must be 0.4mm2 to 0.
PAGE 42
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 1.2.6.1.1 Easy connection scheme See the SB421 installation manual for further details, 1.2.7 BS421 internal backup battery RISK OF EXPLOSION, IF BATTERY IS REPLACED BY AN INCORRECT TYPE Dispose of used batteries according to local rules TetraFlex® 7.
PAGE 43
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x 1.3 BS41X BS 414 Coaxial connectors Connection box CB Antenna Interface AI Receiver Multicoupler divider RMD Channel units TR412 Base station controller BSC412 RFTL combiner 4-channel cavity combiner TC 1.3.1 Environmental/climatic requirements The Base Station is designed to be able to operate at severe environmental conditions.
PAGE 44
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x After placement the four legs under the BS can be adjusted for accurate vertical position to compensate for an uneven floor. In areas with the possibility of earthquakes, it is recommended that the BS be secured to the floor with bolts. Access to the base may require removal of the lowest TX combiner in the rack. Figure 1-20: Level adjustment 1.3.
PAGE 45
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x 1.3.4 Attaching antennas Before installing the Base Station please read the application note in this manual about the Antenna Systems.
PAGE 46
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x Figure 1-23: Power selection Left position = 60V, Right position = 48V The external battery shall be connected in the connection box in top of the BS. Minimum recommended cables dimension is 10mm2 with black for plus (ground) and blue for minus.
PAGE 47
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x The plus pole of the Battery shall be grounded with a 15mm2 yellow/green wire. A protective ground connection shall also be established from the Battery to the BS.
PAGE 48
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x Note: Each of the installed power supplies are individually connected to the AC mains therefore in order to disconnect the Base Station from AC mains, the AC switch of all installed power supplies shall be switched to off. Note: It is recommended that the main power installation includes short circuit back protection which reacts in case of the current is exceeding 16A. TetraFlex® 7.
PAGE 49
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x 1.3.7 Connection Box CB412 Figure 1-27: Connection box 1.3.7.1 Ethernet connect 8 Ethernet connections are present for BSC1 and BSC2: BSC1 LAN1 and 2 and BSC 2 LAN1 and 2 for connection to other nodes, routers, log server, Network Management etc.. BSC1 WAN1 and 2 and BSC2 WAN1 and 2 for connection to corporate network, SIP units, Remote desktop, Switch board (PABX), API etc.
PAGE 50
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x 1.3.7.2 External alarm connections The BS is provided with 8 external alarm inputs. One of these is reserved for the “Door Open” alarm (Not yet implemented) and the rest are currently not pre-defined for a specific function. All alarm inputs are provided with a 1Kohm resistor to +5V. To activate an alarm the input shall be grounded.
PAGE 51
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x The battery lifetime is a critical parameter. High quality back-up batteries normally have a specified lifetime of 10-15 years at normal room temperature. The batteries should also be of the gas-tight type when co-located with the BS to avoid corrosive gases, which may damage the electronics. A battery capacity of 48V 50Ah would be a typical choice for a 4-carrier BS.
PAGE 52
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - BS41x Sensor Battery 48V - Circuit Breaker + 4-Wire Sensor Blue 10sqmm - BS 50A Black 10sqmm Yellow/Green 15sqmm + GND The minus pole of the battery shall be provided with a circuit breaker as close to the battery as possible in order to protect for any excess current flow at a short circuit.
PAGE 53
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS41x 1.3.8.5 Battery deep discharge protect The Base Station is provided with a feature to switch off the load, when the battery is close to being discharged in order to protect the battery. The Base Station is prepared for –60V battery operation, wherefore a switch is placed on the back plane of the BS to indicate to the PS411’s, whether a -48V or -60V battery is used.
PAGE 54
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Basic system parameters PART-2: SW Installation and Configuration TetraFlex® 7.
PAGE 55
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Basic system parameters 2.1 BASIC SYSTEM PARAMETERS TetraFlex® 7.5 software is not compatible with earlier versions, and nodes with e.g. version 7.4 can not interact with nodes with version 7.5. Please consult the document “Update guideline for ver.7.4 to 7.5” for upgrading to TetraFlex 7.5. 2.1.
PAGE 56
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Virus protection 2.2 VIRUS PROTECTION 2.2.1 Introduction The DAMM system is designed with the LAN area as a completely closed IP area without any connection to the outside world. That means, that BSC’s, TR’s etc. without a WAN connection cannot access the outside world and cannot be accessed from the outside world.
PAGE 57
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Virus protection 2.2.2.2 BSC Regarding the DAMM BSC’s running Windows Embedded the risk of infection is much lower as a lot of the services giving problems are not installed here, although the risk of infection still exists.
PAGE 58
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 Damm Cellular Systems A/S, Denmark ® TetraFlex 7.5 Manual - Dongle Configuration 2.3 DONGLE CONFIGURATION 2.3.1 License Dongles 2.3.1.1 Site versus Node: Until the DAMM TetraFlex® system software was introduced the word “Site” has been used to indicate number of Radio Sites in a system. There was coherency between number of “Sites” and number of “Radio sites”.
PAGE 59
Damm Cellular Systems A/S, Denmark o o o o o o Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.
PAGE 60
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Dongle Configuration 2.3.1.3 Dongle settings and combinations APPLICATIONS BSC Network Management DAMM Dispatcher API Log Client Log Server Application Conn Packet data GW BSC node (BSC 4xx) Redundant BSC node (BSC 4xx) Voice GW A detail for each application has been defined in the system planner. Be aware that the selections here may result in additional dongle hardware to be invoiced.
PAGE 61
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Dongle Configuration 2.3.1.5 Spare part Dongle: o A Spare Part Dongle will be offered at a nominal price. If used in the node containing the master subscriber register, the dongle can only be used as spare dongle if the original dongle has no encryption key programmed. In case that encryption key is present, the replacement dongle must be ordered from DAMM sales.
PAGE 62
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Dongle Configuration The total numbers of dongle settings can only be shown with the license dongle reader program that can be found on the “Startmenu” – “Tetraflex” – “Dongle” – “License dongle”: 2.3.1.
PAGE 63
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Dongle Configuration BSC Node: o Dongle Date Limit: If set, the dongle ceases operation when the specified date is reached o Application Date Limit: The Application Date in the SW package is compared to this date for SW update allowance o Nodes Max: The maximum node number which can be defined in the system o Radio Cell TR’s max: Maximum allowed transceivers per radio cell o Voice Gateway Conn.
PAGE 64
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Dongle Configuration API DLL: o Dongle Date Limit: If set, the dongle ceases operation when the specified date is reached o Voice Streams max: Number of simultaneous voice streams in the application o Flags: Discreet listening – if flag is set discreet listening into ongoing calls is possible on the API (e.g.
PAGE 65
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Dongle Configuration dongle updates for the total population of dongles. This update can be implemented if convenient together with the new Software Releases, at an appropriate time.
PAGE 66
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Software installation 2.4 SOFTWARE INSTALLATION All software is preinstalled from factory on the CF Storage media in the SB421 or BSC412. This includes also the BS421, TR412, Power supply- and combiner software. The next chapter is covering the re-installing or updating of software on these units. Also installation of relevant software on external PC is covered.
PAGE 67
Damm Cellular Systems A/S, Denmark 2.4.2 Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Software installation Windows License The TetraFlex® has previously been delivered with the Windows XPe embedded OS Due to outdate of XP from Microsoft, future systems will be delivered with Windows Embedded Standard 2009 (WES2009) The license label on the BSC will state which version is initially delivered.
PAGE 68
Damm Cellular Systems A/S, Denmark o o o o Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Software installation Windows Embedded Standard 2009 (WES2009) XP Windows 7 Windows Server 2008 R2 Installing the new Release can be done in different ways: o Installing whole image including XP - relevant when upgrading SB421 and BSC412 from releases older than 7.30 e.g. 7.
PAGE 69
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Software installation o Go to …\Tetra\Active\Pgm\BSC directory and open the file ImageSetup.bat file for editing o Edit the file (delete REM notes) for the configuration needed (recommendation is all except headlines) o Insert the correct IP and data (PC Name) in the top “set” lines (do not edit the bottom “set” lines) o Save the file o DO NOT RUN.
PAGE 70
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Software installation o Copy “…\Pgm\BSC\BSC.exe” into the active folder in the BSC “C:\Tetra\Active\”. o Restart the BSC. o Repeat the above two points for all BSC’s in the system. 2. If the system is installed with older TetraFlex releases please follow the Update guideline for ver.7.4 to 7.5 3.
PAGE 71
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Software installation 2. If the system is installed with older TetraFlex releases please follow the Update guideline for ver.7.4x to 7.5 Having an OM shortcut on the desktop, change it to point at “C:\Tetra\Active\pgm\OM\OM.vbs”. 2.4.4.4 NM Stop the NM program - when running. 1. If the system is installed with TetraFlex release 7.5: o Copy all files from “…\Pgm\NM\” into the active folder: “C:\Tet
PAGE 72
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - Software installation If you are allowed to restart the BSC you may place the Dispatcher files in c:\tetra\update\pgm\dispatcher\ They will then be copied to the right directory when activating “BSC BackupUpdateRestart” Having any unwanted files in any of the above mentioned folders (e.g. from older installations) please delete them before copying the new Dispatcher installation files. 2.4.4.
PAGE 73
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Configuration 2.4.4.8 PS421 The power supply software (PS421.hex) is placed in c:\tetra\active\pgm\PS421 directory. The PS421 can be upgraded by using the OM command M68/PS421/+ 2.4.4.9 TR412 When unpacking the software package the TR412.bin file will be placed in \Tetra\Active\Pgm\TR412. Download this file to all TR412 by using the TetraOM command: H68/TR412/A 2.4.4.
PAGE 74
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Configuration 2.5 SB421 CONFIGURATION The SB421 enables you to connect a VGA monitor and a USB keyboard directly to the SB421 without having an external PC. In case no graphics is shown, press + + to reset the connection. 2.5.1 Initial setup 2.5.1.
PAGE 75
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Configuration WARNING: Be careful not to disable the USB ports in the BIOS. When USB ports are disabled, the dongle cannot be read and there is no way of getting direct access to the SB421 PC by means of a monitor and keyboard / mouse. 2.5.1.3.1 Hard disk disable NOTE: In case of an internal hard disk is present, disable this totally before booting from the CF card.
PAGE 76
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Configuration Figure 2-4: Boot configuration Figure 2-5: Display configuration TetraFlex® 7.
PAGE 77
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Configuration Figure 2-6: I/O selection Figure 2-7: Port configuration 2.5.1.3.3 BIOS setup for new fast Compact Flash (CF) Cards Due to a BIOS incompatibility, the use of new CF cards requires a change in the BIOS set up: o Enter the BIOS setup by pressing F2 key under boot o Select the MAIN area TetraFlex® 7.
PAGE 78
Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® Damm Cellular Systems A/S, Denmark TetraFlex 7.5 Manual - SB421 Configuration Figure 2-8: BIOS main selection o Select Secondary Master Figure 2-9: USER type change o Select “TYPE” and change type to “Auto” by tapping the key o Press to save the setting and exit the BIOS setup 2.5.1.4 IP address set-up For the TetraFlex® system all IP addresses except for multi node networking is preset upon delivery.
PAGE 79
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - SB421 Configuration 2.5.1.4.1 Default network card IP address setup As default the IP addresses are defined as o LAN Network Card: 172.16.1.10 This IP address must be equal to the IP address defined for the BSC If these IP’s addresses are miss-configured, in addition to a non working system, also a PS alarm may show on the BSC LED’s o WAN Network Card: DHCP 2.5.1.
PAGE 80
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration Figure 2-11: Change MAC 2.6 BS421 CONFIGURATION 2.6.1 Ethernet Connection The BS421 supports 1 x 10/100 Mb/s. Ethernet connection and 1 x Ethernet type DC connection for timing. The purpose of the connections is o To establish SB421 connection for control of the base station o To establish connection to another BS421 for timing and synchronization. (1 sec Pulse).
PAGE 81
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration However, if the BS421 is connected to another BSC, the IP address configuration must be reset. 2.6.1.1.2 How does DHCP work with the SB421 (BSC)? The IP address may be assigned by means of DHCP. This means that the SB421 must first be started. When the SB421 is started her after the BS421/1 must be started and then in a dual carrier system the BS421/2.
PAGE 82
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration o Below the dotted line one or more MAC [In Brackets] / IP addresses are shown. o If only one MAC / IP is shown, change the IP address to 172.16.1.11 o If more IP’s are shown and only one BS421 is connected, determine which IP address is valid by use of a ping command to the IP’s. Delete the wrong IP / MAC entries and change the remaining IP to 172.16.1.
PAGE 83
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration Then select “STOP” to temporarily stop the DHCP server. When the IP setup of the main SB421 is finished, o The dhcpsrv.ini file must be copied to the C:\ProgramFiles\DHCPserver of the redundant SB421 o The IPBIND setting must be changed from IPBIND_1=172.16.1.10 to IPBIND_1=172.16.1.19 o The DHCP server must be started up again TetraFlex® 7.
PAGE 84
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration 2.6.1.1.
PAGE 85
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration 2.6.1.1.5 TR421 Update / Install For updating the transceiver program; TR421.dll on the BS421, use this procedure: o Change the IP addresses used in “TR421Download.bat” file (path c:\tetra\active\pgm\TR421\) with the actual IP addresses to match the TR421's. o The address of the first TR is default 172.16.x.
PAGE 86
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration NB: Update only NK.BIN and Boot.ini if you are adviced to do so (in case they are damaged or need to be updated). Installation of NK.bin file (Windows CE): Refer to section 2.6.2.1 Installation of the Boot.bin file: o Copy the Boot.bin file to the root of the TR421 CF-Card.
PAGE 87
Damm Cellular Systems A/S, Denmark o o o o o o o o o o o Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration Search for BS421 using Start -> Search -> Files or Folders -> Computer Enter the IP address of the BS421 e.g. 172.16.1.11 or 172.16.1.12 Select Search Select the search result Select CF-Card Create a new directory called CF-Card\TMP on the BS421 Copy the file NK.bin from SB421 C:\tetra\PGM\TR to the CF-Card\TMP on BS421 Open VNC for TR1 or TR2 from the desk
PAGE 88
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration Figure 2-16: NK.BIN copy o o After successful copy, delete the CF-Card\TMP directory Restart BS421 using switch in SB421 2.6.2.2 Configure admin user When a new NK.bin file has been copied to the BS421, the BS421 Admin and User settings are lost.
PAGE 89
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration The gateway will restart and prompt for username and password o o Enter username = admin Enter password = tetra 2.6.2.3 Configure host name o Insert BS421-“BS421 serial number” o Press Apply. To move on, it might be necessary to temporarily make a change to the Device Name and press .
PAGE 90
Damm Cellular Systems A/S, Denmark Doc. No. Rev. Date DRAFT 1.01 2012-01-27 ® TetraFlex 7.5 Manual - BS421 Configuration Figure 2-19: Configure user and password 2.6.3 Copy to and from Compact Flash Card (CF Card) on BS421 o o o o o Use Explorer to connect to BS421 Start -> Search -> For files or folders -> Computers Enter TRx IP address 172.16. 1.11 for TR1, 172.16.1.12 for TR2 and so on Check that the S/N is correct When connected, update the CF card as required TetraFlex® 7.