GARAGE Models DOOR OPENER 9357·9367 For Residential Use Only Owner’s Manual Please read this manual and the enclosed safety materials carefully! Fasten the manual near the garage door after installation. The door WILL NOT CLOSE unless The safety is connected and properly aligned. Periodic checks of the opener are required to ensure safe operation. The model number label is located on the left side panel of your opener www.seaside.net.cn DALIAN SEASIDE DOOR CONTROLLING SYSTEM CO., LTD.
INTRODUCTION Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them.
Tools needed During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below.
Overview/Carton Inventory GARAGE DOOR OPENER ASSEMBLY A B I H C F L D G N E Q O J P K M A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q.
ASSEMBLY HARDWARE H1 Clevis Pin, long Φ8×80 (1) H4 Hex Bolt M8×20(4) H2 Clevis Pin,short Φ8×30 (2) H5 H7 Lag Screw M8×40 (4) CotterΦ2×25(3) Hex H3 H6 Screw M5×20(2) H8 Self-Threading Screw (2) Overview/Carton Inventory 5 Nut M8(4)
INCLUDED ACCESSORIES Wall Control Panel Remote Control NOTE: Accessories will vary depending on the garage door opener model purchased. Depending on your specific model, other accessories may be included with your garage door opener. The instructions for these accessories will be attached to the accessory and are not included in this manual. The images throughout this manual are for reference and your product may look different.
1、Assemble the Rail To avoid installation difficulties, do not run the garage door opener until instructed to do so. CAUTION To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail 1.1 Carefully remove the hanging brackets , sprocket and sprocket holder assembly packaged inside the rail. 1.2 Align the rails on a flat surface as shown. The front rail has seven holes near the pulley assembly. The middle rail has two rail connectors.
H6 6 5 2、Tighten the Chain 2.1 To increase the tension and tighten the chain,turn the tension nut clockwise or adjustable wrench until the nut is spaced properly from the rail end -plate. 2.2 Once the nut is spaced correctly,any additional tightening will overtighten the chain and may cause damage to the system. 2.2 To loose the tension,turn nut counterclockwise. 2.
3、Fasten the Rail to the garage door opener CAUTION To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener. 3.1 Position opener with light facing front of garage. Rest opener head on cardboard or protective surface on floor so opener does not get scratched.Chassis side of opener facing up. 3.2 Position rail onto opener chassis by lining uo rail sprocket,Make sure shaft insert into rail sprocket.Press rail down firmly onto shaft and opener chassis.
WARNING To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS. 2. Install garage door opener ONLY on properly balanced and lubricated garage door.and lubricated garage door. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH. 3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener. 4.
WARNING To prevent possible SERIOUS INJURY or DEATH: · Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. · Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry. · NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware, ALL of which are under EXTREME tension.
concrete anchors (not provided). HARDWARE: H7 Lag Screw M8×40 (2) Option A WALL INSTALLATION 2.1A Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling). 2.2A Mark the holes. Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided. H7 Option B CEILING INSTALLATION 2.1B Extend the vertical centerline onto the ceiling as shown. 2.
HAEDWARE H1 H5 4、Position the garage door opener CAUTION To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. NOTE A 2x4 is ideal for setting the distance between the rail and the door. If the ladder is not tall enough you will need help at this point. If the door hits the trolley when it is raised, pull the trolley release arm down to disconnect the chain connector kit and trolley. Slide the trolley toward the garage door opener.
Hanging the garage door opener will vary depending on your garage. Below are three example installations. Your installation may be different. For ALL installations the garage door opener MUST be connected to structural supports. The instructions illustrate one of the examples below. Finished Ceiling HARDWARE H4 Unfinished Ceiling Hex Bolt M8×20(2) 5.
NOTE: The use of short neck or speciality light bulbs may overheat the end panel or light socket. 6.1 Pull the top sides of the light lens and rotate the light lens down. 6.2 Insert an A19 incandescent or compact fluorescent light bulb (100 watt maximum), into the light socket. 6.3 Clip the lens in the opener.
NOTE: If it is necessary to cut the emergency release rope, seal the cut end with a match or lighter to prevent unraveling. Ensure that the emergency release rope and handle are above the top of all vehicles to avoid entanglement. 7.1 Insert one end of the emergency release rope through the handle. Tie a knot at least 1 inch (2.5 cm) from the end of the emergency release rope. 7.2 Insert the other end of the emergency release rope through the hole in the trolley release arm.
8.1A Center the door bracket on the previously marked vertical centerline used for the header bracket installation. Note correct UP placement, as stamped inside the bracket. 8.2A Position the top edge of the bracket 2"-4" (5-10 cm) below the top edge of the door, OR directly below any structural support across the top of the door. 8.
H5 H2 9.4 9.3 Attach the curved door arm to he door Bring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far bracket using the clevis pin (H13). Attach apart as possible to increase door arm rigidity and with the ring fastener (H19). attach using the bolts (H15), nuts (H20) and lock washers (H21). H5 H3 H2 H4 9.5 Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal.
INTRODUCTION Install the wall control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from the moving parts of the door. Your product may look different than the illustrations. HARDWARE Drywall Anchors (2) Screw M4×30 (2) NOTE: For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box. 1.
To insert or remove the wires from the terminal, push in the tab with a screwdriver tip. 3 Attach the warning labels 3.1 Attach the entrapment warning label on the wall near the door control with tacks or staples. 3.2 Attach the manual release/safety reverse test label in a visible location on the inside of the garage door. Install The Photo Eye Safety System Introduction WARNING Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor.
IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. The sending sensor (with an red LED) transmits an invisible light beam to the receiving sensor (with a green LED).
1.2 Position the mounting bracket against the wall with the curved arms facing the door. Make sure there is enough clearance for the beam to be unobstructed. Attach the mounting bracket to the wall using lag screws. 1.1 Install the sensors to the mounting bracket using the screws. Mounting Bracket Not provided No more than 15cm 2 Wire the Safety Reversing Sensors 2.1 Strip 7/16 inch (11 mm) of insulation from each set of wires. Separate the wires. Twist the white wires together.
To avoid installation difficulties, do not activate the garage door opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into your outlet, contact a qualified electrician to install the proper outlet. THERE ARE TWO OPTIONS FOR CONNECTING POWER: Option A TYPICAL WIRING 1.1A Plug in the garage door opener into a grounded outlet. 1.
Adjustments WARNING Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. · Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. · After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3.
THE Adjustments 1 Program the Travel WARNING Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. · Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. · After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3.8 cm) high object (or 2x4 laid flat) on floor. 1.
1.6 The garage door opener will automatically open the door again,then close the door . 2 Test the Safety Reversal System WARNING Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. · Safety reversal system MUST be tested every month. · After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" high (3.8 cm) object (or 2x4 laid flat) on the floor.
Option B The “CLOSE” position force sensitivity 3.1B Press and hold the SETTING Button until the screen show the number from “1” to “3”. 3.2B Press and release the UP Button and the screen show the “∩” 3.3B Press and release the SETTING Button and the screen show the levels of the force sensitivity. 3.4B Use the UP Bottom to increase the levels, press the DOWN Bottom decrease the levels . The screen show the number of the levels. 3.5B Press and release the SETTING Button and the screen is flashing “||”.
Note :If the garage door opener closes the door when the safety reversing sensor is obstructed,call for a trained door systems technician. Operation IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls 3.
WALL Control Using The Wall Control PUSH BAR Press the push bar to open or close the door. Push Bar Light button Lock LIGHT BUTTON Press the Light button to turn the garage door opener lights on or off. When the lights are turned on they will stay on until the Light button is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after the 3 minutes. The Light button will not control the lights when the door is in motion.
To Open the Door Manually WARNING To prevent possible SERIOUS INJURY or DEATH from a falling garage door: · If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly. · NEVER use emergency release handle unless garage doorway is clear of persons and obstructions. · NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.
· Oil door rollers, bearings and hinges. The garage door opener does not require additional lubrication. Do not grease the door tracks. Repair Parts Rail Assembly Parts 1 2 Sprocket and sprocket holder assembly Installation Parts and Accessories 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Garage Door Opener Parts DESCRIPTION 13 1 12 9 1. Chassis. 4 2. Motor and Hall sensor 8 3. Transformer 5 4. Logic Control Board 5.Light Lens(Model 9357·Model9367) 7 11 6 3 6.Light Socket 2 7. Light socket fixed board 8. End panel with light socket 9. End panel with Logic Control Board 10. Cover (Model 9357·Model9367) 11.Wiring Board 10 12.Strain relief 13.
7 8 flash flash The opener do not runs The opener do not runs 9 flash The opener do not runs L H flash flash The opener do not runs The opener do not runs The travel error Bad logic board Power supply voltage Is not normal Bad logic board Bad logic board Reprogram the travel, refer to page 30. Replace the logic board. Disconnect all power,Check the Power,if the power is normal,replace the transformer. Replace the logic board. Replace the logic board.