OPERATION MANUAL Wireless Remote Controller Kit MODELS BRC7E63W BRC7E66 Thank you for purchasing this Daikin air conditioner. Carefully read this operation manual before using the air conditioner. It will tell you how to use the unit properly and help you if any trouble occurs. After reading the manual, file it away for future reference.
PRIOR TO USE This operation manual is exclusively for instructions on how to use the wireless remote controller. Read also the operation manual attached to the indoor unit and to the outdoor unit for safe usage of the system and maintenance. The air conditioner corresponding to this controller comes under the term “appliances accessible to the general public”. CONTENTS PRIOR TO USE.......................................................................................... [1] ILLUSTRATION ...................
1-1 1 ON OFF 3 8 1-2 H M L DOWN 10 C ON OFF UP 6 TEMP FAN H 4 L TIME 11 C hr. 2 M UP 9 hr. FAN DOWN 13 RESERVE CANCEL hr. 5 TIMER 12 MODE 15 hr.
1. SAFETY CONSIDERATIONS Read the following cautions carefully and use your equipment properly. There are three kinds of safety cautions and tips listed here as follows: WARNING .. Improper handling can lead to such serious consequences as death or severe injury. CAUTION ... Improper handling can lead to injury or damage. It could also have serious consequences under certain conditions. NOTE.......... These instructions will ensure proper use of the equipment.
2. NAMES AND FUNCTIONS OF THE OPERATING SECTION (Fig. 1, 2) 10 DISPLAY “ ” (SIGNAL TRANSMISSION) 1 This lights up when a signal is being transmitted. 11 DISPLAY “ ” “ ” “ ”“ “ ” (OPERATION MODE) ” 2 This display shows the current OPERATION MODE. For straight cooling type, “ ” (Auto) and “ ” (Heating) are not installed. DISPLAY “ 3 4 H M L C 12 13 14 ” (SET TEMPERATURE) This display shows the set temperature. 15 hr. DISPLAY “ hr.
AIR FILTER CLEANING TIME INDICATOR LAMP (Red) 22 Lights up when it is time to clean the air filter. DEFROST LAMP (Orange) 23 Lights up when the defrosting operation has started. (For straight cooling type this lamp does not turn on.) FAN/AIR CONDITIONING SELECTOR SWITCH 24 Set the switch to “ ” (FAN) for FAN and “ ” (A/C) for HEAT or COOL.
Placing the remote controller in the remote controller holder Install the remote controller holder to a wall or a pillar with the attached screw. (Make sure it transmits) Placing the remote controller Removing the remote controller Slide from above Pull it upward [CAUTIONS] • Replace all batteries at the same time, do not use new and old batteries intermixed. • In case the remote controller is not used for a long time take out all batteries in order to prevent liquid leak of the battery.
〈〈FOR SYSTEMS WITHOUT COOL/ 〈〈 HEAT CHANGEOVER REMOTE 〉〉 CONTROL SWITCH〉〉 Refer to figure 1-1, 2 on page [1] 1 MODE OPERATION MODE SELECTOR 1 (1) Select OPERATION MODE with the COOL/HEAT CHANGEOVER REMOTE CONTROL SWITCH as follows. OPERATION MODE SELECTOR COOLING OPERATION ............. “ ” HEATING OPERATION .............. “ ” ” ” ” FAN OPERATION....................... “ ” • In this operation mode, COOL/HEAT changeover is automatically conducted. DRY OPERATION ......................
• As the frost on the coil of an outdoor unit increase, heating effect decreases and the system goes into DEFROST OPERATION. • The fan operation stops and the DEFROST lamp of the indoor unit goes on. After 6 to 8 minutes (maximum 10 minutes) of DEFROST OPERATION, the system returns to HEATING OPERATION. Heating capacity & Outdoor air temperature • Heating capacity drops as outdoor air temperature lowers. If feeling cold, use another heater at the same time as this air conditioner.
A. UP AND DOWN DIRECTION • The movable limit of the flap is changeable. Contact your Daikin dealer for details. Press the AIR FLOW DIRECTION ADJUST button to select the air direction as shown below. DISPLAY appears and the air flow direction continuously varies. (Automatic swing setting) Press AIR FLOW DIRECTION ADJUST button to select the air direction of your choice. DISPLAY vanishes the air flow direction is fixed (Fixed air flow direction setting).
2 PROGRAMMING TIME UP DOWN Press the PROGRAMMING TIME button and set the time for stopping or starting the system. UP When this button is pressed, the time advances by 1 hour. DOWN When this button is pressed, the time goes backward by 1 hour. HOW TO SET MASTER REMOTE CONTROLLER (For VRV system) • When the system is installed as shown below, it is necessary to designate the master remote controller. For Heat pump system When one outdoor unit is connected with several indoor units.
When the indoor unit with master remote controller is set to “COOL”, you can switch over operation mode between “FAN”, “DRY” and “COOL”. When the indoor unit with master remote controller is set to “HEAT”, you can switch over operation mode between “FAN” and “HEAT”. When the indoor unit with master remote controller is set to “FAN”, you cannot switch operation mode. When attempting settings than that consented above, a “peep” is emitted as a warning.
Two remote controller control system Two remote controllers control one indoor unit. (In case of group control system, one group of indoor units) The unit follows individual operation. NOTES • Cannot have two remote controller control system with only wireless remote controllers. (It will be a two remote controller control system having one wired and one wireless remote controllers.) • Under two remote controller control system, wireless remote controller cannot control timer operation.
2 UP DOWN Press PROGRAMMING TIMER BUTTON and change the unit number. Press to change the unit number until the indoor unit beeps and perform the following operation according to the number of beeps. Number of beeps Press until the indoor unit makes a long beep. The malfunction code is fixed when the indoor unit makes a long beep. 7 MODE Reset of the display Press OPERATION MODE SELECTOR BUTTON to get the display back to the normal stae. 3 short beeps .... Perform all steps from 3 to 6 .
[Trouble] 1 The RUN lamp of the indoor unit is flashing and the unit does not work at all. Malfunction Code Unit No. which sensed trouble ON OFF Nnmber TEMP TIME UP CODE FAN Operate the indoor unit with the remote controller of the same number. Signal transmitted from a remote controller of a different number cannot be accepted. (If the number is not mentioned, it is considered as “1”) 2. The system operates but it does not sufficiently cool or heat. • If the set temperature is not proper.
3PA63363-21T EM00A046 (0101) HT