OPERATION MANUAL Wireless Remote Controller Kit MODEL BRC7C812 Read these instructions carefully before installation. Keep this manual in a handy place for future reference. This manual should be left with the equipment owner.
1 ON OFF ON OFF 8 TEMP 3 H M L DOWN 10 H F M L TIME F UP UP 6 11 FAN DOWN FAN 13 RESERVE CANCEL 4 9 hr. hr. 2 hr. TIMER 12 MODE 15 hr. SWING 14 5 TEST 16 TEST TEST 7 17 Fig. 1-2 The situation which opened the front cover of the remote control Fig. 1-1 24 21 20 19 25 18 Fig. 2 23 Fig.
CONTENTS ILLUSTRATIONS .....................................................................3 1. SAFETY CONSIDERATIONS ..........................................4 2. NAMES AND FUNCTIONS OF THE OPERATING SECTION ........................................................................4 3. HANDLING FOR WIRELESS REMOTE CONTROLLER.................................................................5 4. OPERATION PROCEDURE ............................................6 5. NOT MALFUNCTION OF THE AIR CONDITIONER .......
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ON/OFF BUTTON Press the button and the system will start. Press the button again and the system will stop. FAN SPEED CONTROL BUTTON Press this button to select the fan speed, HIGH or LOW, of your choice. TEMPERATURE SETTING BUTTON Use this button for SETTING TEMPERATURE. (Operates with the front cover of the remote controller closed.) PROGRAMMING TIMER BUTTON Use this button for programming “START and/or STOP” time.
Placing the remote controller Slide from above. Removing the remote controller Pull it upward. 〈〈FOR SYSTEMS WITHOUT COOL/HEAT CHANGEOVER REMOTE CONTROL SWITCH (Fig. 1-1~2 on page 3)〉〉 1 MODE OPERATION MODE SELECTOR Press OPERATION MODE SELECTOR button several times and select the OPERATION MODE of your choice as follows. Remote controller holder How to put the dry cell batteries (1)Remove the back cover of the remote controller to the direction pointed by the arrow mark.
(2)Press OPERATION MODE SELECTOR button several [°F] times and select “ ”. (This operation is only available during dry operation.) Setting temperature 2 ON OFF ON/OFF Press ON/OFF button. OPERATING INDICATOR lamp lights up or goes off and the system starts or stops OPERATION. NOTE • Do not turn off power immediately after the unit stops. Then, wait no less than 5 minutes. Water is leaking or there is something else wrong with the unit.
Operation mode Cooling Heating • When operating continuously at horizontal at horizontal air flow direction. • When room temperature is higher than the set temperature • At defrost operation (Air flow direction becomes horizontal so that cool air is not exposed directly to the human body) Operation condition NOTE • If you try cooling or programmed drying, while the flaps are facing downward, air flow direction may change unexpectedly. There is nothing wrong with the equipment.
• Only the master remote controller can select HEATING, COOLING or AUTOMATIC OPERATION. When the indoor unit with master remote controller is set to “COOL”, you can switch over operation mode between “FAN”, “DRY” and “COOL”. When the indoor unit with master remote controller is set to “HEAT”, you can switch over operation mode between “FAN” and “HEAT”. When the indoor unit with master remote controller is set to “FAN”, you cannot switch operation mode. 1 long beep ..............
COOLING / HEATING changeover is impossible. • If the indoor unit emits a receiving sound “1 long beep”. It is because the indoor unit under the control of operation changeover is set to the mode that cannot be selected. Display Indicates only a part. • Even if the unit is in operation, the display shows only operational indication. Even if the indication is shown, the indication other than operation disappears after a while. It is because the remote controller is set to multi-system.
Operate the indoor unit with the remote controller of the same number. Signal transmitted from 1 remote controller of a different number cannot be accepted. (If the number is not mentioned, it is considered as “1”.) The system operates but it does not sufficiently cool or heat. • If the set temperature is not proper. (See page 7) • If the FAN SPEED is set to LOW SPEED. (See page 7) • If the air flow angle is not proper. (See page 7) Contact the place of purchase in the following case.
3P153711-2B EM04A061A (0504) FS