DWBP-B3L1KA-AGN 2007.10.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 1 mac001 1200DPI 90LPI Introduction Thank you for purchasing the Digital PVR. Equipped with the latest technology and design, the DSD-9502T/ 9502TFP/ 9502TFPB/ 9503T/ 9503TFP/ 9503TFPB/ 9504TFP/ 9504TFPB is a set-top box ideal for digital terrestrial broadcast reception.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 2 mac001 1200DPI 90LPI Important care and safety advice This Digital PVR has been manufactured to meet international safety standards, but you must take care to operate it safely. It is important that you read these safety instructions. If you have any doubts about the installation, operation, or safety of this Digital PVR, contact Daewoo, as shown in the next page.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 3 mac001 1200DPI 90LPI Important care and safety advice • Do not block the ventilation holes of the Digital box. Allow at least 10 cm on all sides of the Digital box (including top, but excluding the base) for ventilation. Cleaning • Cleaning : always disconnect from the mains supply before cleaning. Wipe with a lintfree cloth or one that has been slightly dampened with clean water. Never use detergents, liquid cleaners.
DWBP-B3L1KA-AGN 2007.10.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 5 mac001 1200DPI 90LPI Front Panel 1 2 3 7 4 5 6 8 1 Power On indicator 2 Remote indicator 3 Hard disk drive indicator ; will be visible when hard disk drive is in use ie when in record or time shift mode. 4 Menu Button ; allows access to on screen menu. 5 OK button ; can be used to select a menu or confirm menu options. 6 Standby Button ; switches between Operation and Standby modes.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 6 mac001 1200DPI 90LPI Rear Panel 1 2 4 3 5 6 1 RF IN ; connects your aerial. 2 Audio L/R ; connects to your TV or VCR and outputs audio signals. 3 T V Scart ; connects a T V SCART cable. 4 RF OUT ; connects an RF to the RF (ANT) input on your TV or VCR. 5 S/PDIF ; outputs the digital audio signals. 6 VCR/DVD SCART ; connects to your VCR/DVD.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 7 mac001 1200DPI 90LPI Remote Control 1 2 3 4 5 Mute ; pauses the audio temporarily. TV/DVR ; switches between DVR and TV. Number buttons EPG ; Electronic Programme Guide Menu ; choose and change a wide range of PVR’s features. Or exit the menu. 6 Arrow buttons ; allows you to move through menu’s. Or navigates in playback mode. 7 Record ; initialises the record - see relevant section in this manual. 8 Channel +/- ; allows you to change channel.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 8 mac001 1200DPI 90LPI Connecting the PVR SCART connections offer the best picture and sound quality. They can also tell your TV when the Digital PVR is switched on and off and whether widescreen pictures are being broadcast. Therefore this is the way this box has been designed to be connected. 1. Connect your aerial to the Digital PVR. • • Make sure your TV is switched off, together with any other equipment you are connecting to it.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 9 mac001 1200DPI 90LPI Connecting the PVR • • • Connect a SCART cable between the SCART TV socket on your Digital PVR and your TV SCART IN socket. Connect an RF cable between the ‘RF OUT’ socket on the Digital PVR and the RF input socket on your VCR. If there isn’t already one in place, connect a second RF cable between the RF output on your VCR and the RF input socket on your TV.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 10 mac001 1200DPI 90LPI Installation wizard Using your Digital PVR for the first time. The first time you use your Digital PVR, you will see a screen like the one below. The Digital PVR now needs to scan for available Digital TV channels. • Press [OK] on your Digital PVR’s remote control to begin searching for digital channels. The search will take between 2 and 5 minutes, depending on the digital TV service in your area.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 11 mac001 1200DPI 90LPI Basic Operation This chapter describes functions such as switching channel, volume control and basic features for watching programmes. Using Standby When you are not watching TV, you should set your Digital PVR to ‘Standby’. To do this: Press the [POWER(√)] button to switch to STANDBY. If you plan to leave your Digital PVR unattended for a long period, switch it off and unplug it at the mains supply.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 12 mac001 1200DPI 90LPI Basic Operation Using the TV Guide (EPG) The TV Guide shows a full list of available channels and programmes. To view the Guide : 1 Press [EPG]. 2 Press […/†] to scroll through the list of channels. 3 To scroll through the programmes press [œ/√]. To scroll forwards and backwards, one day at a time, press the blue and the yellow colour buttons. To review information about the highlighted channel, press [INFO].
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 13 mac001 1200DPI 90LPI Now and Next Information Now and Next gives you information on the current and next programmes on each channel. 1 To open the Now/Next menu press [INFO]. This displays information on the programme showing Now. 2 To see more detailed information press [INFO] again. 3 To see information on the programme showing Next, press [√]. 4 To change the channel you want information for press […/†]. 5 To watch the highlighted channel press [OK].
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 14 mac001 1200DPI 90LPI PIP and T ime Shifted Recording Picture-in-Picture (PIP) Screen If you press the [PIP] button on the remote control while watching TV, you can watch 2 channels at the same time. The Audio from the Main screen will be outputted. Each time you press the [PIP] button, the PIP screen is switched on or off. PIP screen Normal screen Note: • The PIP screen is not available while recording two channels simultaneously.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 15 mac001 1200DPI 90LPI PIP and Time Shifted Recording 1. Time shift information First enter time shift mode by pressing the [TIME SHIFT] button this will pause live TV and press the [PLAY] button to continue watching TV or if you press the [INFO] button in time shift record mode, the time shift information will be displayed. The time shift information displays the current operation status and the time difference between the broadcasting point and watching point.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 16 mac001 1200DPI 90LPI Recording and Playback Using the built-in hard disk drive, you can record a programme without an external media device such as a VCR. Instant Recording Press the [REC] button on the remote control to record the current programme instantly. If you change channels while recording and press the [REC] button, recording starts on that channel also. You can record up to two channels simultaneously.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 17 mac001 1200DPI 90LPI Recording and Playback Timer You can delete recording schedules by going to “Menu - Timers”. Or easily by pressing the [TIMER] button. Adding new recording schedules is available in programme guide. You can record up to two channels simultaneously. Whilst recording two channels simultaneously, only the programmes which are being recorded can be viewed unless you playback a previous recording, or switch your TV to an alternative channel.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 18 mac001 1200DPI 90LPI Recording and Playback Programme Playback You can view the recorded programmes in the Menu - Recordings library. You can also view the recorded programme list by pressing the [LIBRARY] button. 1 Select the desired programme to playback using the […/†] button and then press the [PLAY] button to playback the programme. 2 Press the [STOP] button to stop the current programme and go to the current live programme.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 19 mac001 1200DPI 90LPI Using the Main & Setup Menu’s The Main menu lets you choose and change a wide range of your Digital PVR’s features. • To access the Main Menu, press [MENU].
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 20 mac001 1200DPI 90LPI Using the Main & Setup Menu’s Channel list - lets you delete, reorder, lock, favourite and rename the channel line up. Channel list shows only the favourite list of channels when favourite mode is on. You can easily enter the channel list menu by pressing the [OK] button while watching a channel. MENU Channel list Programme guide Timers Recordings library Setup Favourites - lets you edit the favourite channel list.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 21 mac001 1200DPI 90LPI Using the Main & Setup Menu’s Programme guide - - displays programme information about each channel, based on the date and time. You can also schedule your recording using the information given. Refer to page 12~13 for more information. You can shrink and expand time range and navigate to previous or next day by the colour buttons.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 22 mac001 1200DPI 90LPI Using the Main & Setup Menu’s Setup - Recordings Start early, End late : sets the start and end timing for programme guide recording. These menus are valid only when record type is 'time'. Max timeshift : sets the maximum timeshift time. But this time is not exact because the size of broadcasting stream is different case by case. Auto discard : sets the method of discarding recordings when HDD capacity is not enough.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 23 mac001 1200DPI 90LPI Using the Main & Setup Menu’s Setup - Configuration 1 Country : sets country. Broadcasting RF band is different for each country. 2 Subtitle : sets subtitle on/off. 3 TV type : lets you change how programmes are displayed on your TV (widescreen 16:9 or normal 4:3). 4 TV Out : sets TV output option either RGB or CVBS. 5 Favourite mode : sets favourite mode. (Off, list 1~5) 6 AC3 audio : sets digital audio on/off.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 24 mac001 1200DPI 90LPI Using the Main & Setup Menu’s Installation 1 Automatic channel scan - If your product is connected to the aerial and television, you can automatically search channels without entering any other information. 2 Manual channel scan - You can search channels manually by pressing the [numerical] buttons. 3 Format disk - can format (erase) the disk drive if necessary. 4 First time installation - restores the product to the default settings.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 25 mac001 1200DPI 90LPI W here to get more help If you have any problems using your Digital PVR and cannot find a solution in this user guide: For general problems contact Daewoo helpline on 0870 100 25 25 Or e-mail us at information@desuk.co.uk If possible when calling, you should be close to your TV and have your Digital PVR and TV switched on. For general Freeview reception enquires Freeview : 08708 80 99 80 or www.freeview.co.uk Digital TV Group : www.dtg.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 26 mac001 1200DPI 90LPI Specification UHF Channel DVB Compatible Decoding Video Audio Symbol rate Power Power requirements RF Connection TV Connection Accessories Channel 21-69 -75 to -20 dBm Bandwidth 8 MHz ETS 300 744 MPEG2 compatible (DVB/Main profile@Main level) 1.5~15Mb/s (720 x 576) MPEG2 - Musicam (layer 1&2) (32, 44.1, 48kHz) 2~40 Mbaud Input Voltage : 100–240V~, 50/60Hz 20W max 18W in operation 11.5W in standby IEC connector 169-2 (female),diameter 9.
DWBP-B3L1KA-AGN 2007.10.1 4:58 PM ˘ ` 27 mac001 1200DPI 90LPI Specification Disposal of Used Electrical &Electronic Equipment The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste.
REGISTERING YOUR NEW DAEWOO PRODUCT The information provided will be held on computer by the DAEWOO Registration Department of Domestic & General Insurance Co. Limited for the provision of warranty insurance or product related purposes. The information will not be disclosed to third parties, should you prefer not to receive product related details writes to Domestic & General Insurance Co. DAE REG / 295 Limited, on the address overleaf. TODAY DATE OF PURCHASE TEAR OFF HERE AND RETURN MODEL No.
1200DPI 90LPI mac001 ` 29 ˘ 2007.10.1 4:58 PM DWBP-B3L1KA-AGN DAEWOO GUARANTEE CONDITIONS This product is guaranteed for 12 months from the date of original purchase. Any defect that arises due to faulty materials or workmanship will be repaired free of charge during this period by the dealer from whom you purchased the unit. The guarantee is subject to the following provisions.