GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.
G G G "CAUTION: Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human G contact during normal operation. The antenna should not be contacted during G operation to avoid the possiblility of exceeding the FCC radio frequency exposure limit. The minimum separation distance of 20 cm from the antenna to the body of G user required.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) DOCUMENT HISTORY REVISION DATE COMMENTS 1.0 2008.01.08 1 2.0 2009.04.30 Modified as per H/W Rev.B3 2.1 2009.07.20 Modified as per H/W Rev.C1 & FCC ST official version (H/W Rev.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) Table of Contents DOCUMENT HISTORY...................................................................................... 3 1. Introduction .................................................................................................. 5 2. Systems Configuration ................................................................................ 7 3. Wireless Sensing Unit.......................................................................
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 1. Introduction z The GreenOK-II® Wireless Thermo-Hygro Monitor measures and transmits the temperature and humidity via 2.4GHz Zigbee wireless technology. The Wireless Sensing Units(WSU) can be installed anywhere within a 300 meters radius from the Base Monitoring Unit(BMU). Adding on additional wireless sensing units couldn’t be easier. Once installed, the units work together to keep you on top of the environmental conditions.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 2. Systems Configuration z GreenOK-II is composed of Wireless Sensing Unit(WSU) for temperature and humidity monitoring and Base Monitoring Unit(BMU) for displaying the data from wireless sensing unit and Wireless Repeater Unit(WRU) which retransmit the data from WSU. z The Wireless Sensing Unit (WSU) measures the temperature and humidity value and transmits the data wirelessly to the base monitoring unit. It transmits the data over 2.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 3. Wireless Sensing Unit 3.1 Functional Description z SENSOR_ID ̲ Shows the current SENSOR ID of the unit. z GROUP ID z z Shows the current GROUP ID of the unit. TEMP/VOLT1 ̲ Shows the current temperature, voltage 1 as per operating mode. z HUMID/VOLT2 ̲ Shows the current humidity, voltage 2 as per operating mode.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 3.2 How to set the DIP Switch #1 DEVICE TYPE ཛ The DEVICE TYPE can be configured as one of GMS-120ZB, GMS-130ZB and GMS-140ZB as per the sensor connected. ཛྷ The default TYPE is GMS-120ZB. ཝ If the wrong DEVICE TYPE is configured, you may not read the correct data. TX INTERVAL ཛ The TX INTEVAL can be configured as 15sec or 1sec. ཛྷ The default INTERVAL is 15 seconds.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 3.3 How to set the DIP Switch #2 SENSOR ID ཛ The SENSOR ID can be configured as one of 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 and 16. The default ID is ‘1’. ཛྷ Please avoid SENSOR ID duplication. GROUP ID ཛ The GROUP ID can be configured as one of 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 and 16. The default ID is ‘1’. ཛྷ Please avoid GROUP ID duplication.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 3.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 4. Base Monitoring Unit 4.1 Functional Description z Initialization: Power up the BMU and initialization operation follows. ࣭The firmware version displays. ࣭The 16 STATUS LED light red and green just one time. ࣭Every LED displays from 0 to 9 in sequence. ࣭Beep sounds two times. z SENSOR_ID ̲ Sensor ID automatically rotates 1, 2, 3, … , 16 in sequence at 3 seconds intervals. z GROUP ID ̲ GROUP ID can be set among 1, 2, 3, … , 16.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) z TEMP_HIGH / TEMP_LOW Alarm Setting Button ̲ To increase or decrease the TEMP_HIGH or TEMP_LOW alarm value, press these buttons until you get the desired values. ̲ The default TEMP_HIGH alarm value is 40Ȕ. ̲ The default TEMP_LOW alarm value is -40Ȕ. z POWER ON/OFF Button ̲ When AC power adapter is used, the power is continuously supplied to the unit and Power ON/OFF button does not operate.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 4.2 How to set the DIP Switch #1 DEVICE TYPE ཛ The DEVICE TYPE can be configured as one of GMS-220ZB, Repeater and Test Mode as per operation mode. ཛྷ The default TYPE is GMS-220ZB. TEMP UNIT ཛ The TEMP UNIT can be configured as one of Ȕ and ‘F. ཛྷ The default UNIT is Ȕ.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 4.3 How to set the DIP Switch #2 GROUP ID ཝ The GROUP ID can be configured as one of 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 and 16. The default ID is ‘1’. ཞ Please avoid GROUP ID duplication.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 4.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 4.5 How to set Temperature Alarm Value ཛ Press the SET button for 3 seconds until the TEMP_HI and TEMP_LO LED flash simultaneously which showing current temperature alarm values of SENSOR ID 1. ཛྷ To set the temperature high alarm value, press the UP and DN button of TEMP_HI field. The temperature high alarm value increases or decreases in 1Ȕ interval ranging between -40Ȕ to 120Ȕ.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 5. Replacing the Batteries z This product uses 2 C-size alkaline batteries. If the LED of sensing unit doesn’t blinking for several minutes, follow these steps to replace the batteries; ̲ Unscrew the 4 screw of the unit. ̲ Remove the old batteries. ̲ Make sure you install into the correct direction. ̲ Place the cover and screw firmly the 4 screw.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 6. Specifications 6.1 GMS-120ZB Item Measurement range (Display) Resolution Accuracy Radio Specification Dimension Weight Description Temperature: -40Ȕ a Ȕ Humidity: 1% ~ 99% RH Volt: 0.0V ~ 1.500V Temperature: 0.1Ȕ Humidity: 0.1% Volt: 0.001V Temperature: ±0.5Ȕ @25Ȕ Humidity: ±3% RH Volt: 0.005V IEEE802.15.4 Zigbee 2.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 6.3 GMS-140ZB Item Measurement range Resolution Accuracy Radio Specification Dimension Weight Description Volt: 0.0V ~ 1.500V Volt: 0.001V Volt: 0.005V IEEE802.15.4 Zigbee 2.
GreenOK-II : Wireless Thermo-Hygro Monitor User’s Manual (Rev 2.1) 6.4 GMS-220ZB Item Max. Group ID Display Range Display Resolution Display Contents Radio Specification Dimension Weight Description 16 units 16 groups Temperature: -40Ȕ ~ 120Ȕ Humidity: 1% ~ 99% RH Volt: 0.0V ~ 1.500V Temperature: 0.1Ȕ Humidity: 0.1% Volt: 0.001V Sensor & Group ID Temperature & Relative Humidity Volt1 & Volts2 Temp-High, Temp-Low Alarm Setting Communication/Low Battery Status IEEE802.15.4 Zigbee 2.