User’s Manual: ABC-220 Series (SL) Revision 1.1 Adjustable Bed Controller (ABC-220 Series) User’s Manual Elisync Technologies LLC.
User’s Manual: ABC-220 Series (SL) Revision 1.1 LABELLING REQUIREMENTS (FCC Part 15.19 (a)(3)) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. INFORMATION TO THE USER (Part 15.
User’s Manual: ABC-220 Series (SL) Revision 1.1 DOCUMENT HISTORY REVISION DATE 1.0 2006.09.05 1.1 2006.09.28 COMMENTS st 1 official version released. Elisync Technologies LLC.
User’s Manual: ABC-220 Series (SL) Revision 1.1 CONTENTS DOCUMENT HISTORY...................................................................................... 3 CONTENTS........................................................................................................ 4 1. Introduction .................................................................................................. 5 1.1 Features................................................................................................. 5 1.
User’s Manual: ABC-220 Series (SL) Revision 1.1 1. Introduction 1.1 Features ABC-220 series adjustable bed controller is for adjust the bed to fit any position you like. With wireless hand control, you can raise your head and/or your feet to a position that most comfortable to you. It controls the vibration motors for massage as well as the head and foot actuators. Various massage operation such as single massage, dual massage, and wave massage can be achieved with wireless hand control.
User’s Manual: ABC-220 Series (SL) Revision 1.1 1.2 Systems Configuration Elisync Technologies LLC.
User’s Manual: ABC-220 Series (SL) Revision 1.1 2. Hand Control 2.1 Specification Item Model LCD User Interface Bed Position Control Specification ABC-220HC-020 TIME/ALARM Display & Setting 2 Actuators: Head, Foot 2 Massage Motors: Back, Leg Massage Mode: Manual / Wave Massage Function Massage Intensity: 20~100% Wave Interval: 10~250cycle/min Timer: 30min Radio Frequency Radio Transmission Range Power Supply Dimension Weight Operating Condition 315MHz (FCC Part C 15.231) Max.
User’s Manual: ABC-220 Series (SL) Revision 1.1 2.3 Dimension 30mm 62mm Elisync Technologies LLC.
User’s Manual: ABC-220 Series (SL) Revision 1.1 3. Control Box 3.1 Specification Item Model Bed Position Control Specification ABC-200CB-010 2 Massage Motors: Back, Leg 2 Massage Motors: Back, Leg Massage Mode: Manual / Wave Massage Function Massage Intensity: 20~100% Wave Interval: 10~250cycle/min Timer: 30min Radio Frequency AC Power Input Dimension Weight Operating Condition 315MHz (FCC Part C 15.
User’s Manual: ABC-220 Series (SL) Revision 1.1 3.3 Dimension (mm) Elisync Technologies LLC.
User’s Manual: ABC-220 Series (SL) Revision 1.1 4. Control Box - Details 4.1 Front View Layout 4.2 Rear View Layout 4.3 ACTUATOR Connectors PCB Header - MOLEX 5569-4pins, Right Angle/Dual Row Cable Receptacle - MOLEX 5557-4pins, Dual Row PIN Assignment - Pin 1: UP Pin 2: GND Pin 3: NEUTRAL Pin 4: DOWN Elisync Technologies LLC.
User’s Manual: ABC-220 Series (SL) Revision 1.1 4.4 MASSAGE MOTOR Connectors PCB Header - MOLEX 5569-4pins, Right Angle/Dual Row Cable Receptacle - MOLEX 5557-4pins, Dual Row PIN Assignment - Pin 1: MASSAGER Pin 2: GND Pin 3: NEUTRAL Pin 4: N/C 4.5 AC INPUT Connector PCB Header - Hanlim LAB1143-03, Right Angle Cable Receptacle - Hanlim CHB1143-03 PIN Assignment - Pin 1: NEUTRAL - Pin 2: GND - Pin 3: HOT(LINE) 4.
User’s Manual: ABC-220 Series (SL) Revision 1.1 4.7 STATUS LED GREEN LED - Power Status, Wireless Pairing Status 4.8 PAIRING Button For pairing between Hand Control and Control Box. 4.9 PCB Layout (Fuse, Header) Safety SWITCH Header - Jumper ON: Switch disabled - Jumper OFF: Switch enabled Fuse: AC250V, 10A Elisync Technologies LLC.
User’s Manual: ABC-220 Series (SL) Revision 1.1 5. System Setup Method 5.1 Wireless PAIRING Setup 1) In hand control, press and hold the USER button for 3 seconds to go into pairing mode. The RED INDICATOR light will begin to flash in 1 second interval. In pairing mode, the hand control continuously transmits its unique ID. Press the USER button to stop the RED INDICATOR light flashing and exit from pairing mode. 2) In control box, press and release the PAIRING button to go into pairing mode.
User’s Manual: ABC-220 Series (SL) Revision 1.1 6. Hand Control Operation 6.1 Bed Position HEAD UP/DOWN Button To raise the head of the bed, press and hold the HEADUP button. Release the button when you achieve the desired bed position. To lower the head of the bed, press and hold the HEAD-DOWN button. Release the button when you achieve the desired bed position. FOOT UP/DOWN Button To raise the foot of the bed, press and hold the FOOTUP button.
User’s Manual: ABC-220 Series (SL) Revision 1.1 6.2 Bed Position Call MAX Button To make the bed its maximum position, press the MAX button. The head and foot position of the bed move automatically to the maximum position. LEVEL Button To make the bed flat, press the LEVEL button. The head and foot position of the bed move automatically until the bed become flat.
User’s Manual: ABC-220 Series (SL) Revision 1.1 6.3 Manual Massage Mode Back Massage UP/DOWN Button Press the UP or DOWN button to activate back massage motor with 30 minutes timer. The back massage motor starts with intensity level 5 for 1 second and then drops to last intensity level used. Whenever UP button is pressed, the back massage intensity level is increased to 1 level higher. Whenever DOWN button is pressed, the back massage intensity level is decreased to 1 level lower.
User’s Manual: ABC-220 Series (SL) Revision 1.1 6.4 Wave Massage Mode WAVE Button Press the WAVE button to activate the ‘Wave Program 1’with 30 minutes timer. Press the WAVE button 2nd time to activate the ‘Wave Program 2’. Press the WAVE button to toggle between Program 1 and Program 2 repeatedly. Press the WAVE button for 2 seconds to stop both massage motors. At the end of 30 minutes, both massage motors are automatically turned off.
User’s Manual: ABC-220 Series (SL) Revision 1.1 6.5 Time & Alarm Mode To set CLOCK Time Press and hold the button for 2 seconds to go into Clock setting mode. The HH and MM will begin to flash in 1 second interval for 10 seconds. Press the HOUR button to increase and set the hour. Press the MIN button to increase ands set the minute. Press the button again to exit from Clock setting mode. To set ALARM Time Press and hold the button for 2 seconds to go into Alarm time setting mode.