Installation Instructions Renaissance ® Electric Range with induction cooktop Models: RR30NS[-C], RR30NFS[-C], RR30NIS[-C] and RR30NIFS[-C] Part No. 105910 Rev.
Table of Contents Important Safety Instructions...................................................... 1 Important Information About Safety Instructions......................... 1 Safety Symbols in this Manual....................................................1 General Safety Precautions......................................................... 2 Product Specifications.................................................................3 Electrical Requirements (Except models ending with -C)...........
Important Safety Instructions Important Information About Safety Instructions The Important Safety Instructions and warnings in this manual are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you do not understand.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, explosion, electric shock, serious injury or death when installing or using this appliance, follow basic safety precautions, including the following: warning • Read all instructions before using the appliance. • • Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. Install or locate this appliance only in accordance with these installation instructions.
Product Specifications warning IMPORTANT: Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Electrical Requirements (All models numbers except those ending with -C) It is the owner’s responsibility to ensure that a licensed electrician performs the installation of the electrical supply for this appliance.
Product Specifications Product Dimensions Product tolerances: ±1/16” (±1.6 mm), unless otherwise stated Front of open door Front of handle Front panel Rear of front panel A B C D 1” (2.5 cm) 9” (22.9 cm) backguard* Backguard thickness 6” (15.2 cm) 3” (7.6 cm) backguard* backguard* RR30NI[F]S: 3/8” (9.5 mm) thick top trim External handle shown, some models have integral handle (see inside cover) Product width: 29 15/16” (76.0 cm) RR30N[F]S: full stainless steel side panels RR30NI[F]S: 3” (7.
Installation Specifications Cabinet Layout • warning • • • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • All minimum cabinet/countertop clearances shown on the following pages must be met or exceeded. • To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above surface units should be avoided.
Installation Specifications Cabinet Cutouts for Self-Rimming Installation (Models RR30NIS and RR30NIFS Only) Countertop 1 5/8 (41.1 cm) max. thickness (see diagrams) 34 3/4” (88.3 cm) to 36 7/8” (93.7 cm) Cut 3” dia. (7.6 cm) holes at back bottom of cabinet for ventilation. • The self-rimming installation of the RR30NI[F]S range creates a “built-in” look where the range trim overlaps and rests on the countertop on both sides and in back.
Installation Specifications Cabinet Cutouts for Self-Rimming Installation with Downdraft Vent (Models RR30NIS and RR30NIFS Only) Countertop 1 5/8 (41.1 cm) max. thickness • Trim kit PN ATKR30SR is required for proper installation of a downdraft vent with this range.
Installation Instructions Verify the Package Contents Verify that all the components below have been provided. If any item is missing or damaged, please contact your dealer immediately. Do not install a damaged or incomplete appliance. Make sure that you have everything necessary to ensure proper installation before proceeding. • • • • • Use and care manual Anti-tip bracket with screws and anchors Oven racks (2) GlideRack type, (1) standard type Razor blade scraper Dacor Cooktop Cleaning Cream 1.
Installation Instructions To determine if the base plate is high enough: a. 4. Determine the location of the range center line and front panel when the range is in its final position based on the Product Dimensions on page 4 and the actual cabinet/cutout dimensions used for the installation. b. Determine and mark the required position of the anti-tip bracket, based on the diagram below. Push the bracket up against the wall in the mounting location. c.
Installation Instructions Backguard Installation Electrical Connection If installing a backguard or changing the factory installed backguard, install it before moving the range into position. Do not install a backguard if installing a downdraft vent. warning • Before proceeding, turn off power to the circuit to which the appliance will be connected at the circuit breaker panel or fuse box.
Installation Instructions Connecting Conduit to the Range NOTE: See page 14 for instructions to connect an appliance cord to the range. 1. Remove the range electrical access cover from the back of the range. 2. If using a 4-wire connection, loosen the grounding screw and remove the neutral to ground jumper link. 3. Remove the nut from the conduit strain relief (not included). 4. Slide the wires and the end of the strain relief into the hole on the bottom of the range electrical box.
Installation Instructions Electrical Connection (cont.) Connecting the Conduit to the House Electrical Junction Box warning • Do not connect the green appliance wire to the neutral (white) supply wire unless local building codes permit. • Do not ground the appliance to a gas supply pipe or hot water pipe. • A grounded cold water pipe must have metal continuity to electrical ground and must not be interrupted by insulating materials. Any insulating materials must be jumped with a length of No.
Installation Instructions Separate No.
Installation Instructions Electrical Connection (cont.) 5. Slide the end of the appliance cord into the strain relief from the bottom of the box. See facing page. Appliance Cord Connections - Where Local Code Permits 6. Connect the white (neutral) wire to the neutral terminal in the box. 7. Connect the L1 wire to the L1 power supply terminal inside the box. 8. Connect the L2 wire to the L2 power supply terminal inside the box. 9.
Installation Instructions L2 L1 Neutral Neutral L2 3-Wire Appliance Cord Plug L1 terminal Neutral terminal L2 terminal Ground L1 4-Wire Appliance Cord Plug L1 terminal Neutral terminal L2 terminal Jumper link Link removed Ground screw L1 wire White wire L2 wire L2 wire Green wire White wire L1 wire Strain relief 3-Wire Appliance Cord Connection Where Local Codes Permit Strain relief 4-Wire Appliance Cord Connection Where Local Codes Permit 15
Installation Instructions Installing the Range Re-installing the Oven Door Peel off the protective layer of plastic that covers the stainless steel surfaces. Freestanding Installation 1. Measure from the floor to the countertop and adjust the leveling legs as required to position the top frame at the desired height, based on the cabinet and countertop installation. 2. Carefully slide the range into position in the cutout. As you slide the unit into place the rear leg should engage the antitip bracket.
Installation Instructions Verifying Proper Operation 1. Remove any packaging from inside the oven. 2. Slide the oven racks onto the supports inside the oven chamber according to the use and care manual. 3. Prior to operating the range, please read the accompanying use and care manual carefully. Important safety, service and warranty information are contained within. 4. Turn on power to the range at the circuit breaker panel or fuse box. 5. Set the clock according to the use and care manual. 6.
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.
