Notice 1. This page uses HQ6301i firmware using the RFID module Documentation is a demo program. 2. The demo application, the screen control part of the program, the host control section, Controlled portion of the module and the module control part consists of the UI. 3. Screen control part of MS Visual Studio 2005 using the project wizard Was designed as a Dialog Based application. 4.
Index Updates ……………………………………………………………………………………………1 Table of Contents ………………………………………………………………………………2 1. Before using ... 1.1 Basic Component …..…………………………………………………………………3 1.2 Name and function of each part …………………..…………………………….4 2. To use 2.1 Connecting to host ……………………………………………………………………5 2.2 Connect to smartphone ……………………………………………………………..7 2.3 Connect to Laptop & PC……………………………………………………………. 8 3. Using the RFID Host Program ………………………………………………………….9 4. More 4.1 Support and Information…………………………………………………………..
1. Before Using 1.1 Basic Accessories ………………………………………………………………… DOTR-900 Belt Clip USB Data / Charging Cable Neck strap Adaptor Notice The products of the manufacturer's specifications and components may change depending on circumstances.
1. Before Using 1.
2. UseNavi를 사용하기 전에 2. To Smart 2.1 Connecting to host ………………………………………………………………….. 1) Power ON / OFF (1) Power on - Press and hold the power switch turned on negative behavior Sounds. (2) power off - power is turned on, press and hold the power switch back on Shut down the power is turned off 2 seconds after the tone. (3) Auto-off - 5 minutes elapsed without any action, the ringing tone 10 seconds Alerts and then automatically turns off the power.
2. UseNavi를 사용하기 전에 2. To Smart 2.1 Connect to host ………………………………………………………………….. 4) Run Status During the execution of commands from the host, the green lamp will turn on the red lamp. Reader to read the tag, the alert tone when the green lamp ulrimyeo Will blink for a minute. 5) Pairing termination / disconnection The connection to the host is disconnected DOTR-900 will make sense after 7 seconds, 7 seconds, if the Tag reading, even if the data is to be a loss.
2. UseNavi를 사용하기 전에 2. To Smart 2.2 Connect to Samrtphone ………………………………………………………………….. 1. Bluetooth enabled devices 1-1), the wireless connection manager is to enable Bluetooth devices. 1-2) DOTR-900 Turn on. 2. Bluetooth device discovery and registration 2-1), beginning - "Set -" Connection -> Bluetooth 2-2) 'devices' tab, then click Add saejangchi HQ_UHF_READER Select 2-3), 'password' without entering the password in the 'Next' button Save to finish. Once stored connections need not remain so again. 3.
2. UseNavi를 사용하기 전에 2. To Smart 2.3 Connect to laptop or PC ………………………………………………………………….. 1. RFIDHOST to install the program. (SetupRFIDBTHOST.msi) 2. USB driver installation 2-1) DOTR-900 as a PC with a USB connection. 2-2) DOTR-R900 turn on. 2-3), the device is connected, "Found New Hardware" install the display, click boyimyeo C drive / Program files / Biznara / RFIDBTHOST / USB.driver 2-4) to insert the password out the window and "choose the encryption key" to select the right window Enter 1234.
3. 2. Program Smart Navi를 사용하기 전에 RFID Host ………………………………………………………………….. INVENTORY Display Rund Tag count Tag ID list list menu Program Exit menu bar menu bar 1.Press the button to run the inventory will run. When the start button to run to the title of the STOP Is changed. STOP button will stop running. 2. Inventory as PC / EPC Tag ID list is displayed on the value. Count Count is cumulative. 3. Tag list window, the clink List menu window will appear.
3. Program RFID Host ……………………………………………………………….. 파일 저장 및 분리하기 Read Program start Tag Memory Bank Tag offset Tag word count Tag data Recovery Tag query mask 1. Press the button to run the tag and then set to detect and read data from memory. Prior to execution Select single_tag config screen. 2. When an error occurs, the status lamp is lit in red. 3. Tag ID, select the button on the left side of the window, you can access the specified ID of the tag is detected. 4.
3. To Use Program RFID Host ……………………………………………………………….. 파일 저장 및 분리하기 Lock Kill password Change access password Change Page Change UII memory TID memory User memory To change the mode of memory, then press the Run button. Xxx skip is selected, the memory does not change the state of the lock.
3. To Use Program RFID Host ……………………………………………………………….. Kill Display kill password Use Password Tag's kill password and executes the input. User password on a mistake by the tag as to prevent the destruction of "tagkiller" is typing. Once a tag kill is not a permanent repair has to be taken.
3. Program RFID Host ………………………………………………………………..
3. Program RFID Host ……………………………………………………………….. 1.Tag query parameter that sets the city. The value of this inventory and access settings on either side Both are applied. 2. Query timeout 0 is no timeout. Unit of seconds. 3. Maximum output can be reduced to 9 dB. 4. The city will select a single tag access test. Link COM port selection Module connection button Bluetooth device search button Bluetooth device ID list window Virtual COM port selection button Virtual COM port Bind operation button 1.
4. More 4.1 Support and Information ………………………………………………………………… 1. A / S Center Information 1) Phone A / S Consultation Phone: 82-2-850-3629 2) Talk time Mon-Fri: 9:00 to 18:00 (lunch time is 12 ~ 13 city consultations. Saturdays and Sundays, public holidays are not a consultation. 3) Service Center Address Guro-gu, Seoul 811, Kolon Science Valley 2nd d.o.tel 412 2. Before requesting repair 1) Your phone number and address, you should probably ask the Camera.
4. More 4.2 Product Specifications …………………………………………………………………. Section Specifications Section RFID Reader Bluetooth RF output power 1W 125 ㎽ Channels 50 79 Modulation PR-ASK GFSK Interfaces Bluetooth 2.0 / USB 1.1 compatible / UART 3.
4. More Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.