DAP-1250
System Requirements • A Network with 802.11g/b wireless devices Package Contents • Access Point • Antenna Please follow below table to install DAP-1250 , otherwise, it may be illegal.
Antenna No. Type Frequency Band Gain (dBi) Conntector ｃable Length cable loss ANT24-0800 Dipole Omni 2400MHz - 2500MHz 8 N female 7m 6 ANT24-1201 Yagi Directional 2400MHz - 2500MHz 12 N female or SMA femal 11.7m 10 ANT24-1400 Panel Directional 2300MHz - 2500MHz 14 N female 14m 12 ANT24-1800 Panel Directional 2400MHz - 2500MHz 18 N female 18.7m 16 ANT24-1801 Yagi Directional 2400MHz - 2700MHz 18 N female 18.
Before You Begin It’s best to use a computer (with an Ethernet adapter) that is connected to a switch or router for configuring the DAP-1250. The default IP address for the DAP-1250 is 192.168.0.50 with a Subnet Mask of 255.255.255.0. You will need to assign your computer a Static IP address within the same range as the DAP-1250’s IP address for the purpose of configuring the DAP-1250. See the Appendix if you need assistance in assigning a Static IP address for your network adapter.
Installation Considerations D-Link wireless devices allow you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Connecting the DAP-1250 Wireless Access Point to Your Network A. First, connect the power adapter to the receptor at the back panel of the DAP-1250 and then plug the other end of the power adapter to a wall outlet or power strip. The Power LED will turn ON to indicate proper operation. B. Insert one end of the cable to the Ethernet port on the back panel of the DAP-1250 and the other end of the cable to your network (switch or router).
Setup Wizard 1.Open your Web browser and type http://192.168.0.50 into the URL address box. Then press the Enter or Return key. 2.Type admin for the username and leave the password field blank. Click OK 3. Once you have logged in, the Home screen will appear. Click Run Wizard 4. Then check next and follow the next steps Step 1 - Set up your new password. You have the option to establish a password.
Step 3 - Encryption The DAP-1250 is capable of two levels of wireless encryption WEP and WPA-PSK. By default the encryption is disabled. You can change the encryption settings for more secure wireless communication.
Technical Support D-Link’s website contains the latest user documentation and software updates for D-Link products. U.S. and Canadian customers can contact D-Link Technical Support through our website or by phone. Copyright c 00 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link Corporation or its subsidiaries in the United States and other countries. Other trademarks are the property of their respective owners.
Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of .. 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules.
申請DGT使用手冊必須包含之資訊: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干 擾。
