Installation Instructions

ManualsBrandsD-Link ManualsComputers & Accessories802.11 a/b/g PCI Adapter

DWL-AG520

specifications subject to change without notice. DWL-G520 03072003

If any of the above items are missing, please contact your reseller.

CD-ROM (containing Drivers, Manual and Warranty)

This product works with the following operating

system software:

Windows XP, Windows

2000, Windows Me, Windows 98SE

Before You Begin

DWL-AG520 Air Xpert Tri-Mode Dualband Wireless PCI

Adapter

Check Your Package Contents

These are the items included with your DWL-AG520 purchase:

Turn on the computer and

Insert the D- Link Air Xpert DWL-AG520

Driver CD in the CD-ROM drive.

The step-by-step instructions that follow are shown

in Windows XP. The steps and screens are similar

for the other Windows operating systems

Insert the D-Link CD Into Your Desktop PC

Do NOT install

the DWL-AG520

Wireless PCI Adapter

into your computer

before installing the

driver software from

the D-Link CD!

You must have at least the following:

• A desktop computer with an available PCI 2.2, 32-bit, 3.3 volt PCI slot

• At least a 500 MHz processor and 128MB of memory

• An 802.11a, 802.11b or 802.11g Access Point (for Infrastructure Mode) or

another 802.11a, 802.11b, or 802.11g wireless adapter (for Ad-Hoc;

Peer-to-Peer networking mode.)

Part No. IG-BDWLAG520

Air Xpert Tri-Mode Dualband

Wireless PCI Adapter

Summary of content (12 pages)

PAGE 1
DWL-AG520 This product works with the following operating system software: Windows XP, Windows Air Xpert Tri-Mode Dualband Wireless PCI Adapter TM 2000, Windows Me, Windows 98SE Before You Begin You must have at least the following: • A desktop computer with an available PCI 2.2, 32-bit, 3.3 volt PCI slot • At least a 500 MHz processor and 128MB of memory • An 802.11a, 802.11b or 802.11g Access Point (for Infrastructure Mode) or another 802.11a, 802.11b, or 802.
PAGE 2
Continued... The Install Screen will appear. Click Install Drivers If the CD Autorun function does not automatically start on your computer , go to Start > Run and type “D:\Setup.exe.” If it does start, proceed to the next screen. Type “D:\Setup.exe.” The letter “D” represents the letter of the CD-ROM drive. Your CD-ROM drive may be a different drive letter.
PAGE 3
Click Next Click Next Click Finish Shut down your computer 3
PAGE 4
Installing the DWL-AG520 Wireless PCI Adapter in Your Computer A. Make sure to turn off your computer and unplug the power cord before you begin. Remove the back or side cover of the computer. B. Carefully guide the DWL-AG520’s antenna through the PCI bracket opening adjacent to the PCI slot you intend to use for the DWL-AB520. C. Install the DWL-AG520 carefully, and firmly set it into the available PCI slot (which is typically white or cream-colored). D.
PAGE 5
Installing the DWL-AG520 Wireless PCI Adapter in Your Computer (cont.) F. Gently connect the antenna to the antenna stand. G. Finished! Desk or Wall-mountable Antenna to wirelessly connect to 802.11a and 802.11b networks Screw Mount The screw that secures the adapter to the back of your computer fits into this slot. Link/Activity LEDs Indicates that the card is properly installed when the computer is on and blinks when data is being transmitted.
PAGE 6
Restart Your Computer When you restart your computer this Found New Hardware Wizard (Windows XP) screen will appear: Select Install the software automatically (Recommended) Click Next For Windows XP: This Hardware Installation alert screen may appear after the desktop computer restarts. Click Continue Anyway to finalize the installation Click Finish to finalize the installation.
PAGE 7
Continued... For Windows 2000, this Digital Signature Not Found screen may appear after your computer restarts. Click Yes to finalize the installation. The D-Link driver software for this device is undergoing Windows Logo testing. Microsoft certification is pending.
PAGE 8
Appendix For Windows XP, if you wish to use the AirXpert utility, please do the following steps. Click the XP Networking icon to use the Zero Configuration Wireless Settings. Click Advanced Uncheck “Use Windows to configure my wireless network settings.
PAGE 9
Appendix (Continued) Using the Configuration Utility A. Status: Displays the MAC Address of the Access Point that is associated with the DWL-AG520. B. SSID: The Service Set Identifier is the name assigned to the wireless network. The factory SSID setting is set to default. C. Frequency: Displays the current frequency used by the adapter. D. Wireless Mode: The factory setting is set to Infrastructure. Ad-Hoc mode is used for peer-to-peer networking. A B C D E F G H I E.
PAGE 10
J. SSID: The Service Set Identifier is the name assigned to the wireless network. The factory SSID setting is set to default. Make changes here to match the SSID on existing Wireless Router or Access Point. K. Wireless Mode: The factory setting is set to Infrastructure. Ad-Hoc mode is used for peer-to-peer networking. L. Data Encryption: The default setting is set to Disabled. The adapter supports WEP and AES when encryption is enabled. J K L M N M.
PAGE 11
Notes 11
PAGE 12
Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone. Tech Support for customers within the United States: D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week.