000BASE-TX to 1000BASE-SX/LX Media Converter User’s Guide RECYCLABLE 19071001TSC6002 Rev.1.
TABLE OF CONTENTS TABLE OF CONTENTS .......... 2 INTRODUCTION ................. 3 ABOUT MEDIA CONVERTER ......................... 3 PRODUCT FEATURES ...... 4 INSTALLATION .................. 5 SELECTING A SITE FOR THE EQUIPMENT..... 5 CONNECTING TO POWER ............................. 5 INSTALLING IN A CHASSIS ............................ 5 MONITORING THE CONVERTER THROUGH MANAGEMENT MODULE ............................... 6 LED INDICATOR ...........................................
I NTRODUCTION Thank you for choosing the 1000Base Gigabit Ethernet Media Converter, The Converter introduced here provides one channel media conversion between 1000BASE-TX and 1000BASE-FX. About Media Converter Media Converter is a network technology specified by IEEE 802.3ab and IEEE 802.3z 1000BASE-TX/FX standards.
P RODUCT F EATURES y y y y y y y y y y Hot-swappable when used with a chassis One-channel media conversion between 1000BASE-TX and 1000BASE-FX Fiber media allows: multi-mode fiber and single-mode fiber using SC connector Link Pass Through function Auto negotiation of duplex mode on TX port Auto MDI/MDI-X for TX port Full wire-speed forwarding rate Front panel status LEDs Used as a stand-alone device or with a chassis Hot-swappable when used with a chassis 4
I NSTALLATION This chapter gives step-by-step installation instructions for the Converter. Selecting a Site for the Equipment As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: 1. 2. 3. 4. 5. The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees Celsius).
y First, install the converter onto a carrier supplied with the chassis: Step 1Step 2Step 3- Unscrew and pull out the media converter board. Plug in the media board to any of the vacant slot. Fit the converter onto the carrier and use the screw to secure it. Monitoring the Converter through Management Module There is a management module that can control this media converter through the chassis system, this media converter can be controlled through Web Browser, SNMP and terminal emulation program.
NOTE: To control the function in a working station, need to collocate together with optional Chassis System and Management Module.
The table below shows how LLCF function is working: Me d ia C o nve rte r A Me d ia C o nve rte r B LINK 3 LINK 2 Fib e r TX RX Copper Co p pe r Fib e r TX RX C a b le 5 C a b le 1 LINK 1 RX TX C a b le 4 C a b le 3 C a b le 2 LINK 4 Gig a b it Switc h RX TX Gig a b it Switc h Link Status Link 1 Link 2 Link 3 Link 4 Disconnect Cable 1 Off On On On Cable 2 Off Off Off Off Cable 3 On On On Off Cable 4 Off Off Off Off Cable 5 Off Off Off Off LLR (Link Loss Return)
Link Status Link 1 Link 2 Link 3 Link 4 Disconnect Cable 1 Off Off Off Off Cable 2 Off On On Off Cable 3 Off Off Off Off Cable 4 Off Off Off Off NOTE: If connecting two converters with LLR function in both end, it is recommended that the monitor end converter had to turn off the LLR function, and turn on the LLR function of the remote end converter.
same time. S PECIFICATIONS Standards: Data Transfer Rate: Duplex Mode: LED indicators: Cable IEEE802.3ab 1000BASE-TX IEEE802.3z 1000BASE-SX/LX 1488000pps for 1000Mbps Full Duplex Mode PWR, LNK/ACT 1000BASE-T -4 pair Cat. 5, EIA/TIA-568 100-ohm screened twisted-pair (STP), up to 100m 1000BASE-SX -62.
