HAPTIC PROCESSOR R300 USER GUIDE 242-914-0001-EN1 – March 2020 Technical Support: 1-888-442-3269 ext. 251 Fax: 450-442-3230 E-mail: supportmfx@d-box.com Visit us at: www.d-box.
LIMITATION OF LIABILITY IN NO CASE AND IN NO WAY, THE PROVIDER OF THIS PRODUCT (D-BOX TECHNOLOGIES INC., THE DISTRIBUTOR OR RESELLER, OR ANY OTHER PARTY ACTING AS PROVIDER) SHALL BE LIABLE AND SUED TO COURT FOR DAMAGE, EITHER DIRECT OR INDIRECT, CAUSED BY AND TO THE USER OF THE MOTION SYSTEM AND WHICH WOULD RESULT FROM AN IMPROPER INSTALLATION OR MISUSE OF THE PRODUCT. “MISUSE” AND “IMPROPER INSTALLATION” MEAN, WITHOUT LIMITATION, INSTALLATION AND USE NOT CORRESPONDING TO THE INSTRUCTIONS IN THIS MANUAL.
TABLE OF CONTENTS TABLE OF CONTENTS ......................................................................................................................................................................................................... I INTRODUCTION ....................................................................................................................................................................................................................1 SAFETY INSTRUCTIONS .........................
Introduction INTRODUCTION CAVEAT: READ THIS GUIDE CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION. The purpose of this guide is to provide detailed instructions about installing and using the D-BOX R300 Haptic Processor (HP-R300). The following sign indicates an installation tip: Read this guide before installing the equipment and keep it in a safe place. Check you have all the equipment required to proceed with the installation. Contact D-BOX if any equipment is missing.
Safety Instructions SAFETY INSTRUCTIONS Failure to comply with the following safety instructions can result in injuries to people or damage to equipment: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this device near water. 6. Only clean the device with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
REGULATORY COMPLIANCE STATEMENTS FCC REGULATORY COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier Trade Name: D-BOX Technologies Inc., Model No.: HP-R300 Responsible Party – U.S. Contact Information D-BOX Technologies Inc. 2172 Rue de la Province, Longueuil, Quebec J4G 1R7 Canada 1-450-442-3003 FCC Compliance Statement This device complies with Part 15 of the FCC Rules.
ISED REGULATORY COMPLIANCE This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
SPECIFICATIONS Dimensions: 10.5 cm x 7.5 cm x 3.5 cm Weight: 100 grams Color: Black Network Connection: Wi-Fi 802.11 b/g/n or Ethernet 10/100 LKAN Power: 5VDC, 2A Motion Output: USB, 4 ports on the side panel Input connection*: 3.5 mm [1/8 in] audio jack Input format*: Analog stereo downmix - from source material encoded in 5.1, 6.1, 7.1, etc.
BOX CONTENT D-BOX Haptic Processor R300 Power supply Quick Start Guide Warranty Statement HP-R300 FUNCTIONS WHAT TO EXPECT Supports audio streaming from any source - providing D-BOX encoding is available for the viewed content including: DVD/Blu-ray players, Netflix, ChromeCast, YouTube, Apple TV, etc. Supports connection to multiple D-BOX enabled motion chairs. Automatically updates firmware and its motion codes via internet.
HP-R300 SETUP HARDWARE 1. Carefully unbox your HP-R300 and remove it from the plastic bag. 2. Please read the online Terms and Conditions before breaking the seal on the box containing your cables. Read and keep all documents contained in the cable box. 3. Plug the USB cable from the KAI-1P or KCU into the port at the back of the HP-R300 - KAI-1P and KCU sold separately. 4. Connect your motion platform to your KAI-1P or your KCU - see details on page TBD. 5.
AUDIO WIRING DIAGRAM RECOMMENDED CONNECTION SETUP Connect the analog Stereo Downmix output from any AV source to the HP-R300’s stereo 1/8” audio IN. ALTERNATE HDMI CONNECTION SETUP Connect the HDMI OUT from your AV source to the Atlona HDMI Multichannel to 2CH converter* and output a Left/Right downmix to the HP-R300. Note that with this converter, you can use the HDMI pass through to connect to your TV.
RECLINERS WIRING DIAGRAM SETUP FOR 1 TO 4 RECLINERS Plug one KAI-1P between each D-BOX seat and the HP-R300. D-BOX STRONGLY ADVISES AGAINST NETWORKING MORE THAN 4 KAI-1P WITH THE HP-R300. 2- D-BOX STRONGLY ADVISES AGAINST USING A USB HUB WITH THE HP-R300. 3- IN BOTH CASES, D-BOX DOES NOT OFFER SUPPORT SERVICE.
SETUP FOR 5 TO 20 RECLINERS You can plug up to four D-BOX KCU to the HP-R300. Connect the first KCA into the KCU, then daisy chain the remaining KCAs. The last KCA in a chain must be a KCA-T.
START-UP AND SPLASH SCREEN WIRED NETWORK CONFIGURATION 1. Connect your tablet to the same router as your HP-R300. 2. The HEMC app detects your HP-R300 automatically.
UPDATING THE HP-R300 SOFTWARE UPDATING THE HP-R300 FIRMWARE AND MOTION CODES The firmware and the Motion Codes library are updated automatically from a remote server. Be sure to always have your HP-R300 connected to your internet network. The update does not disturb your current movie viewing and uploads while you are watching a movie. However, the installation takes place only if your HP-R300 is idle for one hour or the next time you turn it ON.
Copyright 2020© D-BOX Technologies Inc. All rights reserved. HP-R300 is a trademark of, and D-BOX is a registered trademark of, D-BOX Technologies Inc. and/or its affiliates in Canada and certain other countries. All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between D-BOX and any other company. Business hours: Monday to Friday9:00 a.m. to 5:00 p.m.