User's Manual

ManualsBrandsCypress Semiconductor ManualsElectronicsBluetooth Module

Table Of Contents

CYBLE-224110-00

EZ-BLE™ PSoC

XT/XR Module

PRELIMINARY

Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600

Document Number: 002-11264 Rev. *A Revised May 16, 2016

General Description

The Cypress CYBLE-224110-00 is a fully certified and qualified

module supporting Bluetooth



Low Energy (BLE) wireless

communication. The CYBLE-224110-00 is a turnkey solution

that includes onboard power amplifier (PA), low noise amplifier

(LNA), crystal oscillators, chip antenna, passive components,

and the Cypress PSoC

4 BLE. Refer to the PSoC 4 BLE

datasheet for additional details on the capabilities of the PSoC 4

BLE device used on this module.

The EZ-BLE

 PSoC

XT/XR module provides extended

industrial temperature operation (XT) and extended

communication range (XR). The EZ-BLE XT/XR module is a

scalable and reconfigurable platform architecture, combining

programmable and reconfigurable analog and digital blocks with

flexible automatic routing. The CYBLE-224110-00 also includes

digital programmable logic, high-performance analog-to-digital

conversion (ADC), opamps with comparator mode, and standard

communication and timing peripherals.

The CYBLE-224110-00 includes a royalty-free BLE stack

compatible with Bluetooth 4.1 and provides up to 25 GPIOs in a

small 9.5 × 15.4 × 1.80 mm footprint.

Module Description

n Module size: 9.5 mm × 15.4 mm × 1.80 mm (with shield)

n Extended Range: Up to 400 meters line-of-sight

n Extended industrial temperature range: –40 °C to +105 °C

n Up to 25 GPIOs

n 256-KB flash memory, 32-KB SRAM memory

n Bluetooth 4.1 qualified single-mode module

n Certified to FCC, CE, MIC, KC, and IC regulations

n 32-bit processor (0.9 DMIPS/MHz) with single-cycle 32-bit

multiply, operating at up to 48 MHz

n Watchdog timer with dedicated internal low-speed oscillator

n Two-pin SWD for programming

Power Consumption

n TX output power: –18 dbm to +9.5 dbm

n RX Receive Sensitivity: –95 dbm

n Received signal strength indicator (RSSI) with 1-dB resolution

n 1 Second connection interval with PA/LNA active: 26.3 µA

n TX current consumption:

p BLE silicon: 15.6 mA (radio only, 0 dbm)

p SE2438T: 20 mA (PA/LNA only, +9.5 dBm)

n RX current consumption of 16.4 mA (radio only)

p BLE silicon: 16.4 mA (radio only)

p SE2438T: 5.5 mA (PA/LNA only)

n Low power mode support

p Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on

p Hibernate: 150 nA with SRAM retention

p Stop: 60 nA with XRES wakeup

Integrated PA/LNA

n Supports output power up to +9.5 dBm and RX

of -95 dBm

Programmable Analog

n Four opamps with reconfigurable high-drive external and

high-bandwidth internal drive, comparator modes, and ADC

input buffering capability; can operate in Deep-Sleep mode

n 12-bit, 1-Msps SAR ADC with differential and single-ended

modes; channel sequencer with signal averaging

n Two current DACs (IDACs) for general-purpose or capacitive

sensing applications on any pin

n One low-power comparator that operate in Deep-Sleep mode

Programmable Digital

n Four programmable logic blocks called universal digital blocks,

(UDBs), each with eight macrocells and datapath

n Cypress-provided peripheral Component library, user-defined

state machines, and Verilog input

Capacitive Sensing

n Cypress CapSense Sigma-Delta (CSD) provides best-in-class

SNR (> 5:1) and liquid tolerance

n Cypress-supplied software component makes

capacitive-sensing design easy

n Automatic hardware-tuning algorithm (SmartSense™)

Segment LCD Drive

n LCD drive supported on all GPIOs (common or segment)

n Operates in Deep-Sleep mode with four bits per pin memory

Serial Communication

n Two independent runtime reconfigurable serial communication

blocks (SCBs) with I

C, SPI, or UART functionality

Timing and Pulse-Width Modulation

n Four 16-bit timer, counter, pulse-width modulator (TCPWM)

blocks

n Center-aligned, Edge, and Pseudo-random modes

n Comparator-based triggering of Kill signals for motor drive and

other high-reliability digital logic applications

Up to 25 Programmable GPIOs

n Any GPIO pin can be CapSense, LCD, analog, or digital

n Two overvoltage-tolerant (OVT) pins; drive modes, strengths,

and slew rates are programmable

Summary of content (43 pages)

PAGE 1
PRELIMINARY CYBLE-224110-00 EZ-BLE™ PSoC® XT/XR Module General Description The Cypress CYBLE-224110-00 is a fully certified and qualified module supporting Bluetooth Low Energy (BLE) wireless communication. The CYBLE-224110-00 is a turnkey solution that includes onboard power amplifier (PA), low noise amplifier (LNA), crystal oscillators, chip antenna, passive components, and the Cypress PSoC® 4 BLE.
PAGE 2
PRELIMINARY CYBLE-224110-00 More Information Cypress provides a wealth of data at www.cypress.com to help you to select the right module for your design, and to help you to quickly and effectively integrate the module into your design. n n n n Overview: EZ-BLE Module Portfolio, Module Roadmap EZ-BLE PSoC Product Overview PSoC 4 BLE Silicon Datasheet Application notes: Cypress offers a number of BLE application notes covering a broad range of topics, from basic to advanced level.
PAGE 3
PRELIMINARY CYBLE-224110-00 Contents Overview ............................................................................ 4 Module Description ...................................................... 4 Pad Connection Interface ................................................ 6 Recommended Host PCB Layout ................................... 8 Power Supply Connections and Recommended External Components .................................................... 12 Connection Options ...............................
PAGE 4
CYBLE-224110-00 PRELIMINARY Overview Module Description The CYBLE-224110-00 is an integrated wireless module designed to be soldered to the main host board. Module Dimensions and Drawing Cypress reserves the right to select components (including the appropriate BLE device) from various vendors to achieve the BLE module functionality. Such selections will guarantee that all height restrictions of the component area are maintained.
PAGE 5
PRELIMINARY CYBLE-224110-00 Figure 1. Module Mechanical Drawing Top View Side View Bottom View Note 1. No metal should be located beneath or above the antenna area. Only bare PCB material should be located beneath the antenna area. For more information on recommended host PCB layout, see Figure 3 on page 7, Figure 4 and Figure 5 on page 8, Figure 6 and Table 3 on page 9. Document Number: 002-11264 Rev.
PAGE 6
CYBLE-224110-00 PRELIMINARY Pad Connection Interface As shown in the bottom view of Figure 1, the CYBLE-224110-00 connects to the host board via solder pads on the back of the module. Table 2 and Figure 2 detail the solder pad length, width, and pitch dimensions of the CYBLE-224110-00 module. Table 2. Solder Pad Connection Description Name SP Connection Connection Type 32 Solder Pads Pad Length Dimension Pad Width Dimension Pad Pitch 0.71 mm 0.41 mm 0.76 mm Figure 2.
PAGE 7
PRELIMINARY CYBLE-224110-00 To maximize RF performance, the host layout should follow these recommendations: 1. The ideal placement of the Cypress BLE module is in a corner of the host board with the antenna located on the edge of the host board. This placement minimizes the additional recommended keep-out area shown in item 2. Please refer to AN96841 for module placement best practices. 2.
PAGE 8
PRELIMINARY CYBLE-224110-00 Recommended Host PCB Layout Figure 4 through Figure 6 and Table 3 provide details that can be used for the recommended host PCB layout pattern for the CYBLE-224110-00. Dimensions are in millimeters unless otherwise noted. The minimum recommended host PCB pad length is 0.91 mm (0.455 mm from center of the pad to either side) is recommended as shown in Figure 6. The host PCB layout pattern can be completed using either Figure 4, Figure 5, or Figure 6.
PAGE 9
PRELIMINARY CYBLE-224110-00 Table 3 provides the center location for each solder pad on the CYBLE-224110-00. All dimensions reference the to the center of the solder pad. Figure 6 provides the location of each module solder pad. Table 3. Module Solder Pad Location Solder Pad (Center of Pad) Location (X,Y) from Orign (mm) Dimension from Orign (mils) 1 (0.26, 3.37) (10.24, 132.68) 2 (0.26, 4.13) (10.24, 162.68) 3 (0.26, 4.89) (10.24, 192.68) 4 (0.26, 5.66) (10.24, 222.68) 5 (0.26, 6.
PAGE 10
CYBLE-224110-00 PRELIMINARY Table 4 and Table 5 detail the solder pad connection definitions and available functions for each connection pad. Table 5 lists the solder pads on CYBLE-224110-00, the BLE device port-pin, and denotes whether the digital function shown is available for each solder pad. Table 5 denotes whether the analog function shown is available for each solder pad. Each connection is configurable for a single option shown with a 3. Table 4.
PAGE 11
CYBLE-224110-00 PRELIMINARY Table 5. Analog Peripheral Capabilities Pad Number Device Port Pin SARMUX [3] 1 GND 2 XRES 3 P1.5 4 P1.1 5 P1.0 6 P0.1 7 P0.4 8 P0.5 9 P0.7 10 P1.3 11 VDDR 12 P0.6 13 P1.2 14 VDD 15 P1.4 16 P2.1 17 VDDA 18 P2.2 19 P2.6 20 P3.0 21 P2.3 22 VREF 23 P3.4 24 P3.5 25 P3.7 26 P3.1 27 P3.6 28 P2.5 29 P5.0 30 P5.1 31 P2.
PAGE 12
CYBLE-224110-00 PRELIMINARY Power Supply Connections and Recommended External Components Power Connections Connection Options The CYBLE-224110-00 contains three power supply connections, VDD, VDDA, and VDDR. The VDD and VDDA connections supply power for the digital and analog device operation respectively. VDDR supplies power for the device radio and PA/LNA. Two connection options are available for any application: 1. Single supply: Connect VDD, VDDA, and VDDR to the same supply. 2.
PAGE 13
PRELIMINARY CYBLE-224110-00 Figure 8. Recommended Host Schematic for Independent Supply Option Document Number: 002-11264 Rev.
PAGE 14
PRELIMINARY CYBLE-224110-00 The CYBLE-224110-00 schematic is shown in Figure 9. Figure 9. CYBLE-224110-00 Schematic Diagram Document Number: 002-11264 Rev.
PAGE 15
CYBLE-224110-00 PRELIMINARY Critical Components List Table 6 provides the critical components used in the CYBLE-224110-00 module. Table 6. Critical Component List Component Reference Designator Description Silicon U1 76-pin WLCSP Programmable System-on-Chip (PSoC) with BLE Crystal Y1 24.000 MHz, 10PF Crystal Y2 32.768 kHz, 12.5PF Antenna Design Table 7 details the antenna used on the CYBLE-224110-00 module. The Cypress module performance improves many of these characteristics.
PAGE 16
CYBLE-224110-00 PRELIMINARY Electrical Specifications Table 10 provides the absolute maximum electrical characteristics for the Cypress BLE module. Table 10. CYBLE-224110-00 Absolute Maximum Ratings Parameter Description Min Typ Max Unit Details/Conditions VDDD_ABS VDD or VDDA supply relative to VSS (VSSD = VSSA) –0.5 – 6 V Absolute maximum VDDR_ABS VDDR supply relative to VSS (VSSD = VSSA) -0.3 – 3.
PAGE 17
CYBLE-224110-00 PRELIMINARY Table 12. CYBLE-224110-00 DC Specifications (continued) Min Typ Max Unit IDD4 Parameter Execute from flash; CPU at 3 MHz Description – – – mA T = –40 °C to 85 °C Details/Conditions IDD5 Execute from flash; CPU at 6 MHz – 2.5 – mA T = 25 °C, VDD = 3.3V IDD6 Execute from flash; CPU at 6 MHz – – – mA T = –40 °C to 85 °C IDD7 Execute from flash; CPU at 12 MHz – 4 – mA T = 25 °C, VDD = 3.
PAGE 18
CYBLE-224110-00 PRELIMINARY Table 12. CYBLE-224110-00 DC Specifications (continued) Parameter IDD36 Description Min Stop-mode current (VDDR) Typ Max Unit Details/Conditions – – – nA T = –40 °C to 85 °C, VDDR = 1.9V to 3.6V Stop Mode, VDD = 3.6 to 5.
PAGE 19
CYBLE-224110-00 PRELIMINARY Table 14. GPIO DC Specifications (continued) Parameter Description Min Typ Max Unit Details/Conditions 0.05 × VDD – – 1 – Current through protection diode to VDD/VSS – – 100 µA – Maximum total source or sink chip current – – 200 mA – VHYSCMOS Input hysteresis CMOS IDIODE ITOT_GPIO Table 15. GPIO AC Specifications Parameter Description Min Typ Max Unit Details/Conditions TRISEF Rise time in Fast-Strong mode 2 – 12 ns 3.
PAGE 20
CYBLE-224110-00 PRELIMINARY Analog Peripherals Opamp Table 18. Opamp Specifications Parameter Description Min Typ Max Unit Details/Conditions IDD (Opamp Block Current. VDD = 1.8V. No Load) IDD_HI Power = high – 1000 1300 µA – IDD_MED Power = medium – 500 – µA – IDD_LOW Power = low – 250 350 µA – GBW (Load = 20 pF, 0.1 mA. VDDA = 2.7V) GBW_HI Power = high 6 – – MHz – GBW_MED Power = medium 4 – – MHz – GBW_LO Power = low – 1 – MHz – IOUT_MAX (VDDA ≥ 2.
PAGE 21
CYBLE-224110-00 PRELIMINARY Table 18. Opamp Specifications (continued) Parameter Min Typ Max Unit Details/Conditions CLOAD Stable up to maximum load. Performance specs at 50 pF Description – – 125 pF – Slew_rate Cload = 50 pF, Power = High, VDDA ≥ 2.7V 6 – – V/µsec – T_op_wake From disable to enable, no external RC dominating – 300 – µsec – 150 – nsec – Comp_mode (Comparator Mode; 50-mV Drive, TRISE = TFALL (Approx.
PAGE 22
CYBLE-224110-00 PRELIMINARY Table 20. Comparator AC Specifications Parameter Min Typ Max Unit TRESP1 Response time, normal mode, 50-mV overdrive Description Details/Conditions – 38 – ns 50-mV overdrive TRESP2 Response time, low-power mode, 50-mV overdrive – 70 – ns 50-mV overdrive TRESP3 Response time, ultra-low-power mode, 50-mV overdrive – 2.3 – µs 200-mV overdrive Min Typ Max Unit –5 ±1 5 °C Temperature Sensor Table 21.
PAGE 23
CYBLE-224110-00 PRELIMINARY Table 23. SAR ADC AC Specifications (continued) Parameter Description Min Typ Max Unit A_INL Integral nonlinearity. VDDD = 1.71V to 3.6V, 1 Msps Details/Conditions –1.5 – 1.7 LSB VREF = 1.71V to VDD A_INL Integral nonlinearity. VDD = 1.71V to 5.5V, 500 Ksps –1.5 – 1.7 LSB VREF = 1V to VDD A_dnl Differential nonlinearity. VDD = 1.71V to 5.5V, 1 Msps –1 – 2.2 LSB VREF = 1V to VDD A_DNL Differential nonlinearity. VDD = 1.71V to 3.
PAGE 24
CYBLE-224110-00 PRELIMINARY Digital Peripherals Timer Table 25. Timer DC Specifications Parameter Description Min Typ Max Unit Details/Conditions ITIM1 Block current consumption at 3 MHz – – 42 µA 16-bit timer ITIM2 Block current consumption at 12 MHz – – 130 µA 16-bit timer ITIM3 Block current consumption at 48 MHz – – 535 µA 16-bit timer Table 26.
PAGE 25
CYBLE-224110-00 PRELIMINARY Table 30.
PAGE 26
CYBLE-224110-00 PRELIMINARY Serial Communication Table 33. Fixed I2C DC Specifications Parameter Description II2C1 Block current consumption at 100 kHz II2C2 Block current consumption at 400 kHz II2C3 Block current consumption at 1 Mbps II2C4 2 I C enabled in Deep-Sleep mode Min Typ Max Unit Details/Conditions – – 50 µA – – – 155 µA – – – 390 µA – – – 1.4 µA – Min Typ Max Unit Details/Conditions – – 400 kHz Table 34.
PAGE 27
CYBLE-224110-00 PRELIMINARY Table 40. Fixed SPI Slave Mode AC Specifications (continued) Parameter TSSELSCK Description SSEL valid to first SCK valid edge Min Typ Max Unit 100 – – ns Memory Table 41. Flash DC Specifications Parameter Description Min Typ Max Unit Details/Conditions 1.71 – 5.
PAGE 28
CYBLE-224110-00 PRELIMINARY Table 46. Hibernate Reset Parameter VHBRTRIP Description BOD trip voltage in Hibernate Min Typ Max Unit Details/Conditions 1.1 – – V – Min Typ Max Unit Details/Conditions Voltage Monitors (LVD) Table 47. Voltage Monitor DC Specifications Parameter Description VLVI1 LVI_A/D_SEL[3:0] = 0000b 1.71 1.75 1.79 V – VLVI2 LVI_A/D_SEL[3:0] = 0001b 1.76 1.80 1.85 V – VLVI3 LVI_A/D_SEL[3:0] = 0010b 1.85 1.90 1.
PAGE 29
CYBLE-224110-00 PRELIMINARY Internal Main Oscillator Table 50. IMO DC Specifications Parameter Description Min Typ Max Unit Details/Conditions IIMO1 IMO operating current at 48 MHz – – 1000 µA – IIMO2 IMO operating current at 24 MHz – – 325 µA – IIMO3 IMO operating current at 12 MHz – – 225 µA – IIMO4 IMO operating current at 6 MHz – – 180 µA – IIMO5 IMO operating current at 3 MHz – – 150 µA – Min Typ Max Unit Details/Conditions Table 51.
PAGE 30
CYBLE-224110-00 PRELIMINARY Table 55. UDB AC Specifications (continued) Parameter TCLK_OUT_UDB2 Description Prop. delay for clock in to data out, Worst case Min Typ Max Unit Details/Conditions – 25 – ns – Min Typ Max Unit Table 56.
PAGE 31
CYBLE-224110-00 PRELIMINARY Table 56. BLE Subsystem (continued) Parameter Description Min Typ RXSE1 Receiver spurious emission 30 MHz to 1.0 GHz – TBD RXSE2 Receiver spurious emission 1.0 GHz to 12.75 GHz – TBD Max – – Unit Details/Conditions dBm 100-kHz measurement bandwidth ETSI EN300 328 V1.8.1 dBm 1-MHz measurement bandwidth ETSI EN300 328 V1.8.
PAGE 32
CYBLE-224110-00 PRELIMINARY Table 56. BLE Subsystem (continued) Parameter Description Min Typ Unit Details/Conditions – mA Guaranteed by design simulation 15.5 – mA Radio only – 14.5 – mA Radio only TX current at –12-dBm setting (PA2) – 13.2 – mA Radio only ITX,-18dBm TX current at –18-dBm setting (PA1) – 12.5 – mA Radio only Iavg_1sec, 0dBm Average current at 1-second BLE connection interval µA TXP: +9.5 dBm; ±20-ppm master and slave clock accuracy.
PAGE 33
CYBLE-224110-00 PRELIMINARY Environmental Specifications Environmental Compliance This Cypress BLE module is built in compliance with the Restriction of Hazardous Substances (RoHS) and Halogen Free (HF) directives. The Cypress module and components used to produce this module are RoHS and HF compliant.
PAGE 34
PRELIMINARY CYBLE-224110-00 Regulatory Information FCC FCC NOTICE: The device CYBLE-224110-00 complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. Transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 35
PRELIMINARY CYBLE-224110-00 Industry Canada (IC) Certification CYBLE-224110-00 is licensed to meet the regulatory requirements of Industry Canada (IC), License: IC: 7922A-4110 Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca.
PAGE 36
PRELIMINARY CYBLE-224110-00 MIC Japan CYBLE-224110-00 is certified as a module with type certification number TBD. End products that integrate CYBLE-224110-00 do not need additional MIC Japan certification for the end product. End product can display the certification label of the embedded module. KC Korea CYBLE-224110-00 is certified for use in Korea with certificate number TBD. Document Number: 002-11264 Rev.
PAGE 37
CYBLE-224110-00 PRELIMINARY Packaging Table 58. Solder Reflow Peak Temperature Module Part Number Package CYBLE-224110-00 32-pad SMT Maximum Peak Temperature Maximum Time at PeakTemperature 260 °C 30 seconds No. of Cycles 2 Table 59. Package Moisture Sensitivity Level (MSL), IPC/JEDEC J-STD-2 Module Part Number Package MSL CYBLE-224110-00 32-pad SMT MSL 3 Document Number: 002-11264 Rev.
PAGE 38
CYBLE-224110-00 PRELIMINARY Ordering Information Table 60 lists the CYBLE-224110-00 part number and features. Table 60.
PAGE 39
CYBLE-224110-00 PRELIMINARY Acronyms Table 61. Acronyms Used in this Document Acronym Description ABUS analog local bus ADC analog-to-digital converter AG analog global AHB AMBA (advanced microcontroller bus architecture) high-performance bus, an ARM data transfer bus ALU arithmetic logic unit Table 61.
PAGE 40
CYBLE-224110-00 PRELIMINARY Table 61. Acronyms Used in this Document (continued) Acronym Description Table 61.
PAGE 41
PRELIMINARY CYBLE-224110-00 Document Conventions Units of Measure Table 62.
PAGE 42
PRELIMINARY CYBLE-224110-00 Document History Page Document Title: CYBLE-224110-00, EZ-BLE™ PSoC® XT/XR Module Document Number: 002-11264 Orig. of Change Submission Date Revision ECN ** 5144379 DSO 02/19/2016 Preliminary datasheet for CYBLE-224110-00 module. *A Preliminary DSO 05/16/2016 Update datasheet to add FCC and IC certification numbers. Document Number: 002-11264 Rev.
PAGE 43
PRELIMINARY CYBLE-224110-00 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products ARM® Cortex® Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers Interface Lighting & Power Control Memory cypress.com/clocks cypress.com/interface cypress.