User's Manual

ManualsBrandsCypress Semiconductor ManualsElectronicsBluetooth wireless EZ-BLE Module with HomeKit

Table Of Contents

PRELIMINARY

CYBLE-413136-01

EZ-BLE™ Module with HomeKit

Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600

Document Number: 002-19043 Rev. PRELIMINARY Revised May 12, 2017

General Description

The CYBLE-413136-01 is a Bluetooth



Low Energy (BLE)

wireless module solution with integrated Apple HomeKit support,

including the authentication co-processor. The

CYBLE-413136-01 includes onboard crystal oscillators, passive

components, and the Cypress CYW20719 silicon device.

The CYBLE-413136-01 supports a number of peripheral

functions (ADC and PWM), as well as UART serial

communication protocol. The CYBLE-413136-01 includes a

royalty-free BLE stack compatible with Bluetooth 4.2 in a 14.7 ×

20.0 × 1.40mm package.

The CYBLE-413136-01 includes an integrated PCB trace

antenna. The CYBLE-413136-01 is qulaified by Bluetooth SIG,

and includes regulatory certification approval for FCC, ISED, and

CE.

Module Description

n Module size: 14.70 mm × 20.00 mm × 2.60 mm

n Extended Range:

p Up to 400 meters bi-directional communication

[1,2]

p Up to 450 meters in beacon only mode

[1]

n Bluetooth LE 4.2 single-mode module

n Certified to FCC, IED, and CE standards

n Castelated solder pad connections for ease-of-use

n 1024-KB flash memory, 512-KB SRAM memory

n Extended Industrial temperature range: –30 °C to +105 °C

n Cortex-M4F 32-bit processor operating up to 96MHz

n Watchdog timer with dedicated internal low-speed oscillator

Power Consumption

n Maximum TX output power: +8.0 dbm

[3]

n RX Receive Sensitivity: –93 dbm

n Received signal strength indicator (RSSI) with 1-dB resolution

n TX current consumption

p BLE silicon: 5.7 mA (radio only, –16 dbm)

p RFX2401C: 27 mA (PA/LNA only, module +8 dBm)

n RX current consumption

p BLE silicon: 5.8 mA (radio only)

p RFX2401C: 7.5 mA (PA/LNA only)

n Cypress CYW20719 silicon low power mode support

p PDS: 70 μA with 512 KB SRAM retention

p Deep Sleep: 1 μA with 16 KB SRAM retention

p HIDOFF: 350 nA with XRES wakeup

Functional Capabilities

n Apple HomeKit compliant with on-board authentication

co-processor

n Switched-cap Sigma-Delta ADC with internal reference

n UART serial communication block (PUART)

n Four dedicated PWM blocks

n BLE protocol stack supporting generic access profile (GAP)

Central, Peripheral, Observer, or Broadcaster roles

Benefits

CYBLE-413136-01 is fully integrated and certified solution that

provides all necessary components required to operate BLE

communication standards.

n Proven hardware design ready to use

n Large non-volatile memory for complex application devel-

opment

n Over-the-air update capable for development or field updates

n Bluetooth SIG qualified with QDID and Declaration ID

n WICED™ Studio provides an easy-to-use integrated design

environment (IDE) to configure, develop, program, and test a

BLE application

Notes

1. Connection range tested module-to-module in full line-of-sight environment, free of obstacles or interferance sources with output power of +8.0 dBm.

2. Specified as module-to-module range. Mobile phone connection range will decrease based on the PA/LNA performance of the mobile phone used.

3. The CYBLE-413136-01 is capable of higher output power than specified, but is intentionally limited to +8.0dBm due to regulatory requirements for European Standards.

Summary of content (33 pages)

PAGE 1
PRELIMINARY CYBLE-413136-01 EZ-BLE™ Module with HomeKit General Description n The CYBLE-413136-01 is a Bluetooth Low Energy (BLE) wireless module solution with integrated Apple HomeKit support, including the authentication co-processor. The CYBLE-413136-01 includes onboard crystal oscillators, passive components, and the Cypress CYW20719 silicon device. RX current consumption p BLE silicon: 5.8 mA (radio only) p RFX2401C: 7.
PAGE 2
PRELIMINARY Contents Overview 3 Functional Block Diagram ........................................... 3 Module Description...................................................... 3 Pad Connection Interface ................................................ 5 Recommended Host PCB Layout ................................... 6 Module Connections ........................................................ 7 Connections and Optional External Components ....... 7 Power Connections (VCC) ..................................
PAGE 3
PRELIMINARY CYBLE-413136-01 Overview Functional Block Diagram Figure 1 illustrates the CYBLE-413136-01 functional block diagram. Figure 1. Functional Block Diagram Module Description The CYBLE-413136-01 module is a complete module designed to be soldered to the applications main board. Module Dimensions and Drawing Cypress reserves the right to select components from various vendors to achieve the Bluetooth module functionality.
PAGE 4
PRELIMINARY CYBLE-413136-01 Figure 2. Module Mechanical Drawing Top View (See from Top) Side View Bottom View (Seen from Bottom) Notes 4. No metal should be located beneath or above the antenna area. Only bare PCB material should be located beneath the antenna area. For more information on recommended host PCB layout, see “Recommended Host PCB Layout” on page 6. 5. The CYBLE-413136-01 includes castellated pad connections, denoted as the circular openings at the pad location above.
PAGE 5
PRELIMINARY CYBLE-413136-01 Pad Connection Interface As shown in the bottom view of Figure 2 on page 4, the CYBLE-413136-01 has seven main connections that are connected to the host board via castellated solder pads (“CSP”). The CYBLE-413136-01 also includes additional solder pad connections (“SP”) used for debug or testing on the bottom side of the module. Table 2 and Figure 3 detail the solder pad length, width, and pitch dimensions of the CYBLE-413136-01 module. Table 2.
PAGE 6
PRELIMINARY CYBLE-413136-01 Recommended Host PCB Layout Figure 5 (Dimensioned) and Figure 6 (Relative to Origin) provide the recommended host PCB layout pattern for the CYBLE-413136-01. Pad length of 1.27 mm (0.655 mm from center of the pad on either side) shown in Figure 6 is the minimum recommended host pad length. All dimensions are in millimeters. Figure 5. CYBLE-413136-01 Host Layout (Dimensioned) Top View (Seen on Host PCB) Document Number: 002-19043 Rev. PRELIMINARY Figure 6.
PAGE 7
PRELIMINARY CYBLE-413136-01 Module Connections Table 3 details the solder pad connection definitions and available functions for each connection pad. Table 3 lists the solder pads on the CYBLE-413136-01, the silicon device pin, and denotes what functions are available for each solder pad. Table 3 also lists the primary/intended function for each solder pad for the application this module was specifically designed for. Table 3.
PAGE 8
PRELIMINARY CYBLE-413136-01 Figure 7 illustrates the CYBLE-413136-01 schematic. Figure 7. CYBLE-413136-01 Schematic Diagram Document Number: 002-19043 Rev.
PAGE 9
PRELIMINARY CYBLE-413136-01 Critical Components List Table 4 details the critical components used in the CYBLE-413136-01 module. Table 4. Critical Component List Component Reference Designator Authentication Co-Processor U1 Description Apple Authentication Co-processor Silicon U2 40-pin QFN BLE Silicon Device - CYW20719 PA/LNA U3 17-pin QFN - Skyworks RFX2401C Crystal Y1 24.000 MHz, 12PF Antenna Design Table 5 details the PCB trace antenna used in the CYBLE-413136-01 module. Table 5.
PAGE 10
PRELIMINARY CYBLE-413136-01 Bluetooth Baseband Core The Bluetooth Baseband Core (BBC) implements all of the time-critical functions required for high-performance Bluetooth operation. The BBC manages the buffering, segmentation, and routing of data for all connections.
PAGE 11
PRELIMINARY CYBLE-413136-01 Power Management Unit The Power Management Unit (PMU) provides power management features that can be invoked through power management registers or packet handling in the baseband core. This section contains descriptions of the PMU features. Figure 8. Power Management Unit of CYW20719 RF Power Management Figure 8 shows the CYBLE-413136-01 power management unit (PMU) block diagram that is contained in the CYW20719 silicon device.
PAGE 12
PRELIMINARY CYBLE-413136-01 Microprocessor Unit The CYBLE-413136-01 microprocessor unit runs software from the link control (LC) layer up to the host controller interface (HCI). The microprocessor is a Cortex®-M4 32-bit RISC processor with embedded ICE-RT debug and serial wire debug (SWD) interface units. The microprocessor also includes 2 MB of ROM memory for program storage and 512 KB of RAM for data scratch-pad.
PAGE 13
PRELIMINARY CYBLE-413136-01 Figure 9. Reset Timing Integrated Radio Transceiver The CYBLE-413136-01 has an integrated radio transceiver that is optimized for 2.4 GHz Bluetooth wireless systems. It has been designed to provide low power, low cost, and robust communications for applications operating in the globally available 2.4 GHz unlicensed ISM band. It is fully compliant with Bluetooth Radio Specification 3.
PAGE 14
PRELIMINARY CYBLE-413136-01 Calibration The CYBLE-413136-01 radio transceiver features a self-contained automated calibration scheme. No user interaction is required during normal operation or during manufacturing to provide optimal performance. Calibration compensates for filter, matching network, and amplifier gain and phase characteristics to yield radio performance within 2% of what is optimal.
PAGE 15
PRELIMINARY CYBLE-413136-01 Table 7. Common Baud Rate Examples, 48 MHz Clock (continued) Baud Rate (bps) High Rate Low Rate Mode Error (%) 230400 0x0 0xF3 Normal 0.16 –0.08 115200 0x1 0xE6 Normal 57600 0x1 0xCC Normal 0.04 38400 0x11 0xB2 Normal 0.00 19200 0x22 0x64 Normal 0.00 Support for changing the baud rate during normal HCI UART operation is included through a vendor-specific command that allows the host to adjust the contents of the baud rate registers.
PAGE 16
PRELIMINARY CYBLE-413136-01 Figure 10. PWM Block Diagram Triac Control The CYBLE-413136-01 includes hardware support for zero-crossing detection and trigger control for up to four triacs. The CYBLE-413136-01 detects zero-crossing on the AC zero detection line and uses that to provide a pulse that is offset from the zero crossing. This allows the CYBLE-413136-01 to be used in dimmer applications, as well as any other applications that require a control signal that is offset from an input event.
PAGE 17
PRELIMINARY CYBLE-413136-01 Electrical Characteristics Note: All voltages listed in Table 8 are referenced to VCC. Table 8.
PAGE 18
PRELIMINARY CYBLE-413136-01 Core Buck Regulator Table 10. Core Buck Regulator (Internal to Module) Parameter Conditions Input supply voltage DC, VBAT DC voltage range inclusive of disturbances CBUCK output current LPOM only Output over-current limit Peak inductor current Output voltage range Programmable, 30mV/step default = 1.2V (bits=0000) Output voltage DC accuracy Includes load and line regulation: • Before trimming • After trimming Min. Typ. Max. Unit 2.1 3.3 3.
PAGE 19
PRELIMINARY CYBLE-413136-01 Digital LDO Table 11. Digital LDO (Internal to Module) Parameter Conditions Input supply voltage, Vin Minimum Vin=Vo+0.12V requirement must be met under maximum load. Nominal output voltage,Vo Internal default bit setting Output voltage programmability Range Step size Accuracy at any step (including line/load regulation) before trimming Accuracy at any step (including line/load regulation) after trimming Min. Typ. Max. Unit 1.2 1.2 1.6 V – 1.1 – V 0.
PAGE 20
PRELIMINARY CYBLE-413136-01 RF LDO Table 12. RF LDO (Internal to Module) Parameter Conditions Input supply voltage, Vin Min Vin=Vo+0.15V = 1.35V (for Vo=1.2V) Dropout voltage requirement must be met under maximum load. Nominal output voltage,Vo Internal default bit setting 000 Output voltage programmability Range Step size Accuracy at any step (including line/load regulation) Accuracy at any step (including line/load regulation) after trimming Dropout voltage At maximum load Min. Typ. Max.
PAGE 21
PRELIMINARY CYBLE-413136-01 Digital I/O Characteristics Table 13. Digital I/O Characteristics Characteristics Symbol Minimum Typical Maximum Unit VIL – – 0.8 V Input high voltage (VDDO = 3.3V) VIH 2.0 – – V Output low voltage VOL – – 0.4 V Output high voltage VOH VDDO – 0.4V – – V Input low current IIL – – 1.0 μA Input high current IIH – – 1.0 μA Output low current (VDDO = 3.3V, VOL = 0.4V) IOL – – 2.0 mA Output high current (VDDO = 3.3V, VOH = 2.
PAGE 22
PRELIMINARY CYBLE-413136-01 RF Specifications Note: Table 15 and Table 16 apply to single-ended industrial temperatures. Unused inputs are left open. Table 15. Receiver RF Specifications Parameter Mode and Conditions Min Typ Max Unit 2402 – 2480 MHz – –93.0 – dBm –20 – – dBm Receiver Section Frequency range – RX sensitivity GFSK, BDR GFSK 0.1% BER, 1 Mbps Module Maximum input – Table 16.
PAGE 23
PRELIMINARY CYBLE-413136-01 Timing and AC Characteristics In this section, use the numbers listed in the Reference column of each table to interpret the following timing diagrams. UART Timing Table 18. UART Timing Specifications Reference Characteristics Min. Typ. Max. Unit 1 Delay time, UART_CTS_N low to UART_TXD valid. – – 1.50 Bit periods 2 Setup time, UART_CTS_N high before midpoint of stop bit. – – 0.67 Bit periods 3 Delay time, midpoint of stop bit to UART_RTS_N high. – – 1.
PAGE 24
PRELIMINARY CYBLE-413136-01 Environmental Specifications Environmental Compliance This Cypress BLE module is produced in compliance with the Restriction of Hazardous Substances (RoHS) and Halogen-Free (HF) directives. The Cypress module and components used to produce this module are RoHS and HF compliant.
PAGE 25
PRELIMINARY CYBLE-413136-01 Regulatory Information FCC FCC NOTICE: The device CYBLE-413136-01 complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 26
PRELIMINARY CYBLE-413136-01 Innovation, Science and Economic Development (ISED) Canada Certification CYBLE-413136-01 is licensed to meet the regulatory requirements of Innovation, Science and Economic Development (ISED) Canada. License: IC: 7922A-3136 Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits.
PAGE 27
PRELIMINARY CYBLE-413136-01 European R&TTE Declaration of Conformity Hereby, Cypress Semiconductor declares that the Bluetooth module CYBLE-413136-01 complies with the essential requirements and other relevant provisions of Directive 1999/5/EC.
PAGE 28
PRELIMINARY CYBLE-413136-01 Packaging Table 20. Solder Reflow Peak Temperature Module Part Number Package CYBLE-413136-01 14-pad SMT Maximum Peak Temperature Maximum Time at Peak Temperature No. of Cycles 260 °C 30 seconds 2 Table 21. Package Moisture Sensitivity Level (MSL), IPC/JEDEC J-STD-2 Module Part Number Package MSL CYBLE-413136-01 14-pad SMT MSL 3 The CYBLE-413136-01 is offered in tape and reel packaging. Figure 12 details the tape dimensions used for the CYBLE-413136-01. Figure 12.
PAGE 29
PRELIMINARY CYBLE-413136-01 Figure 14 details reel dimensions used for the CYBLE-413136-01. Figure 14. Reel Dimensions The CYBLE-413136-01 is designed to be used with pick-and-place equipment in an SMT manufacturing environment. The center-of-mass for the CYBLE-413136-01 is detailed in Figure 15. Figure 15. CYBLE-413136-01 Center of Mass Document Number: 002-19043 Rev.
PAGE 30
PRELIMINARY CYBLE-413136-01 Ordering Information Table 22 lists the CYBLE-413136-01 part number and features. Table 22 also lists the target program for the respective module ordering codes. Table 23 lists the reel shipment quantities for the CYBLE-413136-01. Table 22.
PAGE 31
PRELIMINARY CYBLE-413136-01 Acronyms Document Conventions Table 24. Acronyms Used in this Document Units of Measure Acronym BLE Description Table 25.
PAGE 32
PRELIMINARY CYBLE-413136-01 Document History Page Document Title: CYBLE-413136-01 EZ-BLE™ Module with HomeKit Document Number: 002-19043 Revision ECN ** PRELIMINARY Orig. of Submission Change Date DSO Description of Change Preliminary datasheet for CYBLE-413136-01 module. Document Number: 002-19043 Rev.
PAGE 33
PRELIMINARY CYBLE-413136-01 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products ARM® Cortex® Microcontrollers Automotive Clocks & Buffers Interface Internet of Things Memory cypress.com/arm cypress.com/automotive cypress.com/clocks cypress.com/interface cypress.