Multi-format to HDMI/VGA Scaler ID # 15202 Operation Manual
Introduction This Multi Input Scaler has Composite Video, Component Video, PC (VGA), and HDMI inputs and can switch and scale the signal to HDMI or VGA with audio outputs. It supports HDMI output resolutions up to 1080p/WUXGA and Analog Digital Conversion (ADC) and Digital Analog Conversion (DAC) allowing a wide range of AV signals to be displayed on a HDMI or VGA display. Further, the Onscreen Display (OSD), IR remote, RS-232, IP and on-panel controls make this product very versatile.
Operation Controls and Functions The following sections describe the hardware components of the unit. Front Panel 1.POWER Button and LED: Press this button to switch the device on or to set it to standby mode. Once the device is connected to an active power supply the LED will illuminate and the device will switch on automatically. 2.IR Receiver Window: Receives only the IR signal from the remote control included in the package. 3.
2.SERVICE: Reserved for manufacturer use only 3.RS-232: Connect to a PC/Laptop or RS-232 control system to use RS-232 commands to control the device (See RS-232 and Telnet Commands Section for details on RS-232 commands) 4.OUTPUT 1) HDMI 1/2:Connect to an HDMI display or AV Receiver for video and/or audio output 2) PC/HD: Connect to a monitor/display for video output. For HD (Component) output, use the supplied D-Sub 9pin to 3 RCA adaptor cable for HD resolutions from 480p~1080p.
Remote Control 1. POWER: Press this button to switch the device on or to set it to standby mode. 2. HDMI1/2/3, PC1/2/3, CV and COMP: Direct source selection keys. Press one of these keys to switch to the required source. 3. MENU: Press this button to enter the OSD menu. 4. EXIT: Press this button to exit the menu or the current selection in the OSD menu. 5. OK & ▲▼◄►: Press OK to confirm the selection or press the arrow buttons to navigate the OSD menu.
RS-232 and Telnet Commands Command Description S POWER 0/1 R POWER 0=OFF 1=ON Reports the numeric equivalent for POWER setting (as above) S SOURCE 1~8 1=HDMI 1 5=VIDEO 2=HDMI 2 6=PC 1 3=HDMI 3 7=PC 2 4=YPbPr 8=PC 3 Reports the numerical equivalent for SOURCE setting (as above) R SOURCE S OUTPUT 0~211 R OUTPUT 0=640×480 11=1600×1200 1=800×600 12=920×1080 2=1024×768 13=1920×1200 3=1280×768 14=480p 4=1360×768 15=720p@60 5=1280×720 16=1080i@60 6=1280×800 17=1080p@60 7=1280×1024 18=576p 8=1440×900 19=72
S HUE 0~60 R HUE S SATURATION 0~60 R SATURATION S SHARPNESS 0~30 R SHARPNESS S NR 0~3 R NR S VOLUME 0~100 R VOLUME S AUDIO DELAY 0~3 R AUDIO DELAY Sets the numerical equivalent for the HUE setting (0~60) Reports the numerical equivalent for the HUE setting Sets the numerical equivalent for the SATURATION setting (0~60) Reports the numerical equivalent for the SATURATION setting Sets the numerical equivalent for the SHARPNESS setting (0~60) Reports the numerical equivalent for SHARPNESS setting 0=OFF 2=MIDD
2=HDMI 2 3=HDMI 3 4=YPbPr 7=PC 2 8=PC 3 ST Checks the FIRMWARE version and SOURCE information: 0.00~x.xx SOURCE: HDMI ~ PC3 PORT ON: LAST ~ PC3 VOL + VOL - Raises the volume level (VOLUME * IS SET) Lowers the volume level (VOLUME * IS SET) QUIT EXIT (Telnet only) Note: 1. Resolution settings 0~13 are RGB encoded. Resolution settings 14~21 are YUV encoded. 2. RS-232 commands will be not executed unless followed with a carriage return (CR) command and for some systems a Line feed (LF) command.
720×576P 50 1280×720P 50 1920×1080I 50 1920×1080P 50 Main Menu Sub Menu 3rd Menu DISPLAY SIZE OVER SCAN 4th Menu FULL* FOLLOW INPUT PAN SCAN LETTER BOX UNDER 2 UNDER 1 MODE INFO OFF INFO* ON INPUT HDCP (HDMI mode only) OFF PC (PC mode only) AUTO SETUP ON* H_POSITION V_POSITION PHASE CLOCK WXGA/XGA XGA* WXGA RESET Main Menu Sub Menu 3rd Menu COLOUR CONTRAST 0~60 (30) BRIGHTNESS 0~60 (30) COLOR R 0~1023 (512) G 0~1023 4th Menu
(512) B 0~1023 (512) R OFFSET 0~1023 (512) G OFFSET 0~1023 (512) B OFFSET 0~1023 (512) HUE 0~60 (30) SATURATION 0~60 (30) SHARPNESS 0~30 (0) NR. OFF* LOW MIDDLE HIGH AUDIO VOLUME 0~100 (100) DELAY OFF* 40ms 110ms 150ms SOUND ON* MUTE SOURCE AUTO* (HDMI mode only) *1 EXT. SETUP FACTORY RESET2 KEY LOCK OFF* ON POWER SAVE OFF* ON IP MODE DHCP* STATIC SET STATIC IP ADDRESS 0.0.0.0.~ 255.255.255.
SUBNET MASK 0.0.0.0.~ 255.255.255.255*4 DEF.GETWA 0.0.0.0.~ 255.255.255.255*5 Y FREE RUN COLOR BLACK BLUE* INFORMATIO INPUT N OUTPUT REVISION IP ADDRESS Note: 1.When the AUDIO SOURCE setting is set to 'AUTO', the device will send the audio signal according to the input source. If the input signal is HDMI, the device will use the HDMI audio signal and if input is DVI, the device will use the external L/R audio.
Telnet Control Before attempting to use the Telnet control, ensure that both the Scaler (via the LAN port) and the PC/Laptop or control system being used are connected to the same active network. To access the Telnet control in Windows 7, click on the "Start" menu and type "cmd" into the Search field then press enter (see below for reference). Under Windows XP, go to the "Start" menu and click on "Run", type "cmd" then press enter (see below for reference).
Note: All command will not be executed unless followed by a carriage return. Commands are case-insensitive. If the IP is changed then the IP Address required for Telnet access will also needs to be change accordingly.
Web GUI Control On a PC/Laptop that is connected to same active network as the Scaler, open a web browser and type device's IP address on the web address entry bar. The browser will bring up the control page of the Scaler. Note: The IP address can be obtained from the OSD menu under Information.
Output Resolution Support Resolution Output PC/HD HDMI 480p/576p HD ٧ 720p@50/60Hz HD ٧ 1080i@50/60Hz HD ٧ 1080p@50/60Hz HD ٧ VGA@60Hz ٧ ٧ SVGA@60Hz ٧ ٧ XGA@60Hz ٧ ٧ SXGA@60Hz ٧ ٧ UXGA@60Hz ٧ ٧ 1280×768@60Hz ٧ ٧ 1280×800@60Hz ٧ ٧ 1360×768@60Hz ٧ ٧ 1400×1050@60Hz ٧ ٧ 1440×900@60Hz ٧ ٧ 1680×1050@60Hz ٧ ٧ 1920×1200@60Hz (RB) ٧ ٧ Specifications Input Ports 3×HDMI, 3×VGA, 1×Component Video, 1×Composite Video, 2×RCA (Analog Stereo L/R), 6×3.
Connection Diagram
