&37 3& WR 9LGHR 2YHUOD\ 23(5$7,21 0$18$/
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: electrical shock and injury to persons. ! moisture or install this product near water. Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction ............................................ 1 2. Applications ........................................... 1 3. Package Contents ................................ 1 4. System Requirements ............................ 1 5. Features .................................................. 2 6.1 Front Panel ........................................3 6.2 Rear Panel.........................................4 6.3 Remote Control ................................5 6.4 RS-232 Protocols ...............
1. INTRODUCTION The PC to Video overlay system is designed to overlay PC/ Graphics signal onto Video signal or vise versa. Moreover, it can convert a variety of VGA sources to Video signal. It is idea for using in applications like video conference, home theater, business presentation and lecturing room. 2. APPLICATIONS Video Conference Home theater Business presentation Lecturing room 3. PACKAGE CONTENTS PC to Video overlay system 5V DC power supply adaptor Operation Manual 3.
5. FEATURES # $% " & superimpose Video signal onto VGA source. Supports VGA to Video conversion *+ 8 ;<= <>= >== ;== ?=@< E;> ?@>= ?=@< ?;== ?@== Video: NTSC, NTSC4.
6. OPERATION CONTROLS AND FUNCTIONS The following sections describe the hardware components of the unit. 6.1 Front Panel MENU/EXIT POWER 1 2 PC KEY 3 4 5 ENTER 6 7 1 POWER LED INDICATOR The LED will illuminate when power is on. 2 POWER Press to power on the system, press again to turn the system to standby. 3 IR SENSOR 4 PC KEY Press the button to display the combination of PC and Video or S-Videio screen. 5 Press to toggle through various control or setting values.
6.2 Rear Panel PC IN INPUT PC OUT RS-232 S IN V IN S IN OUTPUT V OUT S OUT DC 5V 6 7 V IN 1 2 3 4 5 1 RS-232 Connect 3.5mm phone jack to D-Sub 9pin adaptor to the PC/ Notebook device for RS-232 control. 2 PC INPUT Connect the input source equipment such as PC/NB for PC signal input. 3 PC OUTPUT (PASS THROUGH) Connect the display TV/monitor for PC signal output. 4 V-IN AND S-IN Switch between Video or S-Video input.
6.3 Remote Control 1 OSD Press to turn ON/OFF the OSD on the display. 2 POWER 4 Press to power ON or to Standby for the system. 1 3 6 3 V IN Press to select Video input source. Depending on the S/ V IN switch the output display will show S/V video. 7 V IN PC IN PC KEY 1 2 3 4 5 6 7 8 9 2 5 MENU/EXIT ZOOM 9 11 POWER OSD 10 OK RESET 8 RESET 11 4 PC IN Press to select PC input source. 5 PC KEY Press the button to display the combination of PC and Video or S-Video screen.
6.4 RS-232 Protocols Video Scaler Remote Controller PIN ] PIN ] 1 NC 1 NC 2 TXD 2 RXD 3 RXD 3 TXD 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC > NC > NC 9 NC 9 NC Baud Rate: 9600bps ] 8 > Parity: None Stop Bit: 1 Flow Control: None 6.
[OUTPUT2] output mode--PC KEY [OUTPUT3] output mode--CV KEY [OUTPUT4] output mode--MIXER [SYSTEM0] output video system :NTSC [SYSTEM1] output video system :NTSC4.
[ZOOMD] PC PAN down [PANEL0] Front panel lockout on [PANEL1] ' * + [CVCONTx] video Contrast x=0~63 [CVBRIGHTx] video Brightness x=0~63 [CVCOLORx] video Color x=0~63 [CVHUEx] video Tint x=0~63 [CVDETAILx] video Sharpness x=0~63 [CVRESET] Video Adjustment Reset [CVCONT58] [CVBRIGHT31] [CVCOLOR31] [CVHUE31] [CVDETAIL10] [PCCONTx] PC Contrast x=0~63 [PCBRIGHTx] PC Brightness x=0~63 [PCCOLORx] PC Color x=0~63 [PCHUEx] PC Tint x=0~63 [PCDETAILx] PC Sharpness x=0~63 [P
[ASPECTRS] PC aspect reset [PCHSIZE31] [PCVSIZE31] [PCHPOS31] [PCVPOS31] [PCPHASE?] [KEYPHASEx] KEY Adjust Phase x=0~63 [KEYLEVELx] KEY Adjust Level x=0~63 [KEYRESET] KEY adjustment reset [KEYPHASE31] [KEYLEVEL31] [RMCODEx] Remote Code adjustment reset Remote Code x=0~3 9
[STATUS] Retrieve video scaler all status [POWER?] [KEY?] [OUTPUT?] [SYSTEM?] [ZOOM?] [OSD?] [DISPLAY?] [PANEL?] [RMCODE?] [PCCONT?] [PCBRIGHT?] [PCCOLOR?] [PCHUE?] [PCDETAIL?] [PCHSIZE?] [PCVSIZE?] [PCHPOS?] [PCVPOS?] [PCPHASE?] [CVCONT?] [CVBRIGHT?] [CVCOLOR?] [CVHUE?] [CVDETAIL?] [KEYPHASE?] [KEYLEVEL?] [ZOOMC?] }#^@~@ carriage return. Zoom functions are for PC input only.
7.
f% <>@J \ ! + J{ || <>@J \ ! + J{ KEY ADJUST CHROMA KEY: (RED/BLACK/BLUE/ GREEN)*Reset will not change this setting RESET Exit OUTPUT: PC IN/VIDEO IN/PC KEY/ MIXER*3 CV SYSTEM: NTSC/NTSC4.43/PAL/ PAL-M/PAL-N/ SECAM SETUP PC ZOOM: 1 ~9/OFF DISPLAY: INFO/OFF/ON REMOTE 0~3 Exit INFORMATION PC INPUT/CV INPUT/OUTPUT/ VERSION/EXIT Exit Note: 1. Power resetting will turn output display back to default setting.
8. SPECIFICATIONS S-Video Bandwidth ["[{W! Input Format ;<= <>= >[W! >== ;== >[W! ?=@< E;> >[W! ?@>= ?=@< >[W! ?;== ?@== ;=W! NTSC, NTSC4.43, PAL, PAL-M, PAL-N, SECAM Input Port ? $% ? * ? * ^ E[ ? #^* ? * ^ E[ Output Format NTSC, NTSC4.
9.
10.
ZZZ F\SHXURSH FRP
