CP-255ID CV, SV, VGA and DVI to DVI Scaler / Converter OPERATION MANUAL
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction �������������������������������������������6 2. Applications �������������������������������������������6 3. Package Contents ����������������������������������6 4. System Requirements ���������������������������6 5. Features ��������������������������������������������������7 6. Operation Controls and Functions �������8 6.1 Front Panel ��������������������������������������������������� 8 6.2 Rear Panel ����������������������������������������������������� 9 6.
1. INTRODUCTION T he CP-255ID is a Digital Video Scaler designed to accept Composite Video, S-Video, PC, and DVI input signals. These inputs can be switched and scaled and are outputted via DVI port. External audio input signals can be switched and sent to the L/R output port correspondingly with the video source selection. The control can be done through on-panel buttons, IR remote, or RS-232, and there is OSD (On Screen Menu) providing selection and system information.
5.
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel DIGITAL VIDEO SCALER CP-255ID POWER XGA CV SV PC DVI MENU - + ENTER 720P 1 2 3 4 5 1 POWER & LED: Press this button to switch the device ON or to put the device into standby mode. When the device is connected to an active power supply the LED will illuminate and the device will switch ON automatically. 2 IR (IR window): Receives only the IR signal from the supplied remote control.
6.2 Rear Panel 1 2 4 IN SERVICE RS232 DVI OUT 3 L/R OUT DVI L/R PC L SV R DC 5V CV 5 6 1 SERVICE: Reserved for manufacturer use only. 2 RS-232: Connect to a PC or RS-232 control system to control the device with RS232 commands (see Sectionsm 6.5 and 6.6 for details). 3 DVI OUTPUT: Connect to a DVI display (TV/monitor) for PC signal output or to an HDMI display with an HDMI to DVI adaptor. 4 L/R OUT (3.
6.3 Remote Control 1 POWER: Press this button to switch the device ON or to put the device into standby mode POWER 2 CV/SV/PC/DVI: CV Press to directly select the required input. SV DVI 3 EXIT 4 MENU: Press this button to enter the onscreen menu. 2 PC 3 EXIT: Press this button to exit the menu or the current selection in the onscreen menu. MENU 5 AUTO ADJUST CR-118 7 OK & : Press OK to confirm the selection or use the directional buttons to navigate the on-screen menus.
6.
6.
Command Description Contents R HUE Inquire hue setting S SATURATION 0~60 Saturation setting R SATURATION Inquire saturation setting S SHARPNESS 0~30 Sharpness setting R SHARPNESS Inquire sharpness setting S NR 0~3 Noise reduction setting 0=OFF / 1=LOW / 2=MIDDLE / 3=HIGH R NR Inquire noise reduction Reports the numerical equivilent for the setting NR setting (as above) S AUDIODELAY 0~3 Audio delay setting 0=OFF / 1=40ms / 2=110ms(2) / 3=50ms R AUDIODELAY Inquire audio delay setting
6.
1st Layer 2nd layer 3rd Layer SIZE (VIDEO mode only) OVER SCAN 4th Layer FULL BEST FIT PAN SCAN LETTER BOX UNDER 2 UNDER 1 MODE INFO INFO ON OFF PC(PC mode only) AUTO SETUP No YES H_POSITION 0~60 (30) V_POSITION 0~60 (30) PHASE CLOCK WXGA/XGA XGA WXGA RESET NO YES 15
1st Layer 2nd layer 3rd Layer 4th Layer COLOUR COLOUR R 0~1023 (512) G 0~1023 (512) B 0~1023 (512) R OFFSET 0~1023 (512) G OFFSET 0~1023 (512) B OFFSET 0~1023 (512) CONTRAST 0~60 (30) BRIGHTNESS 0~60 (30) HUE (VIDEO mode only) 0~60 (30) SATURATION (VIDEO mode only) 0~60 (30) SHARPNESS (VIDEO mode only) 0~30 (0) NR.
1st Layer 2nd layer 3rd Layer SETUP FACTORY RESET NO 4th Layer YES KEY LOCK OFF ON POWER SAVE OFF ON INFORMATION INPUT OUTPUT REVISION Note: Items in Bold are the Factory default settings.
7.
8. SPECIFICATIONS 8.1 Technical Specifications Video Bandwidth 165 MHz Input Ports 1×Composite, 1×S-Video, ,1×VGA, 1×DVI, 1×L/R, 1×LR, 1×USB (service only), 1×RS-232 (Control Only) Output Port 1×DVI, 1×L/R Input Resolution Support Up to WUXGA & 1080p Output Resolution Support Up to WUXGA & 1080p Power Supply 5V/2.
8.
DVI/HDMI output Resolution Native 640×480@60 Hz 800×600@60 Hz 1024×768@60 Hz 1360×768@60 Hz 1280×720@60 Hz 1280×800@60 Hz 1280×1024@60 Hz 1440×900@60 Hz 1400×1050@60 Hz 1680×1050@60 Hz 1600×1200@60 Hz 1920×1080@60 Hz 1920×1200@60 Hz 480p 576p 720p (@50/60 Hz) 1080i (@50/60 Hz) 1080p (@50/60 Hz) 21
9.
CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton, Middlesex, TW17 8BA Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279 Email: sales@cypeurope.com www.cypeurope.com v1.