CP-255I Analogue to HDMI Scaler / Converter OPERATION MANUAL
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction �������������������������������������������6 2. Applications �������������������������������������������6 3. Package Contents ����������������������������������6 4. System Requirements ���������������������������6 5. Features ��������������������������������������������������7 6. Operation Controls and Functions �������8 6.1 Front Panel ��������������������������������������������������� 8 6.2 Rear Panel ����������������������������������������������������� 9 6.
1. INTRODUCTION Cypress's CP-255I Scaler Box is designed to upscale digital/analog video signals from Composite, S-Video, PC, Component (HD) and HDMI input sources, to digital HDMI output of a wide range of HDTV and PC resolutions including 1080p and WUXGA (1920 x 1200). Aswell as upscaling video, the scaler box also converts digital/analog audio signals to digital format, which can then be output either through HDMI combined with the video signal or separately via the discrete Coaxial S/PDIF output.
5. FEATURES HDMI, HDCP 1.1 and DVI 1.0 compliant. Scales any PC (VGA~WUXGA) or HD (480i~1080p) resolutions to from another PC/HD resolutions. Automatically detects the correct settings of the connected display and outputs the corresponding resolution and refresh rate, when the NATIVE output is selected. Supports 50/60 Hz frame rate conversion. Supports 3D motion video adaptive, 3D de-interlacing, and 3:2 / 2:2 pull-down detection and recovery.
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel Digital Video Scaler Processor POWER CV SV COMP PC HDMI MENU 1 2 3 4 - + 5 ENTER 6 1 POWER Button and LED Indicator Press the button power the unit on or off. When the power is turned on, the LED will illuminate. 2 IR remote control sensor 3 Input Selection Buttons and LED Indicators Press the required button (CV/SV/COMP/PC/HDMI) to select the desired input source. The LED will illuminate to indicate the corresponding input is selected.
6.2 Rear Panel CO-AX OUT 2 4 AUX IN RS-232 7 PC IN R L CO-AX R CV L DC 5V PC IN HDMI OUT HDMI IN Cr/Pr 1 3 5 Cb/Pb 6 Y R L SV 8 9 1 HDMI OUT and CO-AX OUT Connect the HDMI OUT port to the HDMI input port of your display such as HDTV or monitor. Connect the CO-AX OUT port to the Coaxial (S/PDIF) input port of your amplifier for separate digital audio output.
7 CO-AX Input The CO-AX port provides the digital audio input support, and can be assigned to any of the video inputs (CV/SV/COMP/PC/HDMI). Once connected, it can be assigned in the OSD Menu under Audio Source Selection by selecting between Coaxial (S/PDIF) or other audio source (see section 4.3 OSD Operation for reference).
6.
6.4. Remote Control 1. POWER: 4 2 1 3 5 Press the button once to power on the unit. Press again to enter standby mode. 6 2. INPUT: Press the button repeatedly to toggle through 7 8 various input sources. 10 9 3. HD INPUT: 12 11 Press the button to directly select component input. 4. PC INPUT: Press the button to directly select PC input. 5. HDMI/DVI INPUT: Press the button to directly select DVI (or HDMI) input. 6.
7. RS-232 REMOTE CONTROL PROTOCOL 7.1 Pins definition of modem cable The connection between the unit and remote controller with RS-232 modem cable*.
7.
COMMAND CODE RESPONSE DESCRIPTION S SHARPNESS 0~100 > SHARPNESS 0~100 SHARPNESS 0~100 ADJUST [DEFAULT:32] S NR 0~3 > NR OFF~HIGH 0:OFF; 1:LOW; 2:MIDDLE; 3:HIGH, NR CONTROL S PCHPOSITION 0~100 > PCHPOSITION 0~100 H POSITION 0~100 ADJUST S PCVPOSITION 0~100 > PCVPOSITION 0~100 V POSITION 0~100 ADJUST S PCCLOCK 0~100 > PCCLOCK 0~100 PC MODE COLCK 0~100 ADJUST S PCPHASE 0~63 > PCPHASE 0~63 PC MODE PHASE 0~63 ADJUST S COLORTEMP 0~3 > COLORTEMP NORMAL~USER 0:NORMAL; 1:WARM; 2:COOL; S RED 0
7.
8. CONNECTION DIAGRAM Composite video and stereo audio from DVD player CO-AX OUT AUX IN RS-232 PC IN R L CO-AX R L Cr/Pr Cb/Pb Y R L CV DC 5V VGA video and stereo audio (via 3.5 mm jack) from PC/Laptop PC IN HDMI OUT HDMI IN SV S-Video and stereo audio from Blu-ray player Component and stereo audio from DVD player TV or Monitor HDMI from Digital Set-top Box (and optional stereo audio via 3.
9. SPECIFICATIONS 9.1. General Specification Frequency bandwidth 1.65Gbps (single link) Input Ports 1 × Composite/1 × Stereo Audio (L/R) 1 × S-Video/1 × Stereo Audio (L/R) 1 × Component (3 RCA)/1 × Stereo Audio (L/R)` 1 × PC D-Sub (15-pin)/1 × Stereo Audio (3.5mm Phone Jack) 1 × HDMI/1 × Stereo Audio (3.5mm Phone Jack for DVI) 1 × Stereo Audio (3.
9.2.
CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton, Middlesex, TW17 8BA Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279 Email: sales@cypeurope.com www.cypeurope.com v1.
