PU-O4H4C 4 by 4 HDMI V1.
Safety Precautions Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
Table of Contents 1. Introduction.....……………………..…………………................................ 1 2. Applications...........................…..…………………………………….....… 1 3. Package Contents..............................……………………………….……. 1 4. System Requirements.............................……………………………..…… 1 5. Features................................…..…………………………………...……….. 2 6. Specifications.......................................................................................... 3 7.
1. Introduction This HDMI over CAT6 Matrix is a high performance equipment with remote control, IR blaster and receiver. It is compatible with HDMI v1.3 specifications, a cutting-edge technology which defines support for Deep Color (12 bits/color) video and new lossless compressed (Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio) digital audio. It offers you the maximum convenience in HDMI signal distribution, when you need to have multiple HDMI sources and displays connected together.
5. Features HDMI 1.3, HDCP 1.1 and DVI 1.
6. Specifications Frequency Bandwidth Input Ports Output Ports EDID ESD Protection HDMI Audio Output HDMI Cable In HDMI Cable Out CAT 6 Cable Out Color Space IR IN/OUT Deep Color HDMI Resolution DVI Resolution Power Supply Dimensions (mm) Weight(g) Chassis Material Silkscreen Color Operating Temperature Storage Temperature Relative Humidity Power Consumption 2.
7. Operation Controls and Functions 7.1 Front Panel IN IN POWER CMLUX-4H4CAT PU-O4H4C HDMI V1.3 to CAT6 4X4 Matrix 1 2 3 IN IN 4 HDMI OUT OUT HDMI ① HDCP HDMI/DVI 1 2 3 IN IN 4 A A HDCP HDMI/DVI 1 2 3 B B ② IN IN 4 HDCP HDMI/DVI 1 2 3 4 C C HDCP HDMI/DVI D D ③ ④⑤ ①. Remote control sensor. ②. Power switch & LED Indicator: This LED will illuminate when the power is turned on. .
②. ③. ④． ⑤. ⑥. ⑦. ⑧. 2. When EDID is switched to STD, the unit will use its built-in EDID that supports: Video →1080p 12-bit (max) supports xvYCC Audio →PCM 2CH 3. The EDID selection will only be activated after the unit is re-plugged and powered on. RS-232: This slot is where you connect a D-Sub 9-pin cable to the PC COM port when controlling the device over RS-232. Detailed specifications are listed in section 9.
8. Remote Control 1. Power: Press this button to turn on/off the unit. 2. Input Select for HDMI OUT A: Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT A. 3. Input Select for HDMI OUT B: Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT B. 4. Input Select for HDMI OUT C: Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT C. 5. Input Select for HDMI OUT D: Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT D. 5 9. RS-232 Protocol 9.
9.
9.3. IR Cable Pin Definitions IR Blaster IR Receiver ① Power 5V ② IR blaster signal ③ IR blaster signal ① IR signal ② Power 5V ③ Grounding ① ②③ ① ②③ Note: The frequency on both IR Receiver & Blaster can support 20~60KHz. 10. 3.5Ø Connectors Pin Definitions 10.1 IR IN Pin Definitions Pin Assignment 1 Power 5V 2 IR Signal 3 GND 10.2 IR OUT Pin Definitions Pin Assignment 1 IR Blaster Signal 2 Power 5V 3 IR Blaster Signal 10.
11.
A Acronyms Acronym Complete Term CAT6 Catergory 6 Cable DTS Digital Theater Systems DVI Digital Visual Interface EDID Extended Display Identification Data HDCP High-Bandwidth Digital Content Protection HDMI High-Definition Multimedia Interface IR Infrared UXGA Ultra Extended Graphics Array VGA Video Graphics Array 10
