CY-368B-SB MULTI-HANDSET CORDLESS SYSTEM 2.4 GHz Digital DSS CallerID/ Call W aiting Type2 andCall W aiting ID Options Owner’ s Manual Instal lation and operati ng instructions Pl ease read thi s m anual careful l y before use. Keep foryour reference. CALLER ID / CALLER ID CALL W AITING / CALL W AITING ID OPTIONS COM PATIBLE Caller ID, Caller ID Call Waiting, and/or Call Waiti ng ID Opti ons Services, where available, are subscription ser vices.
C ONT E NT S IM PORTANTINFORM ATION IM PO RTANT SAFETY INSTRUCTIO NS SPECIAL FEATURES Q UICK REFERENCE PREPARATION CHARG ING THE BATTERY PACK LO CATIO N O F CO NTRO LS LCD DISPLAY GETTING STARTED CHO O SE THE BEST LO CATIO N CO NNECTING THE BASE UNIT SPARE BATTERY W ALLM O UNTING BASE UNIT REG ISTRATIO N O F HANDSETS CHO O SE THE DIALING M O DE M ENU SETTINGS STRUCTURE AND O PTIO NS M ENU FUNCTIO NS BASIC OPERATION TO M AKE A CALL TO ANSW ER A CALL TO REDIAL A CALL TO M UTE A CALL ADJUSTING HANDSET VO LUM E
C ONT E NT S ADDITIONAL INFORM ATION CAPACITY O UT O F RANG E NO CO NNECTIO N TROUBLESHOOTING CARE AND M AINTENANCE FCC REQUIREM ENTS 45 45 45 45 46 47 48 2
IM PORTAN T IN FOR M AT ION I mportantSafety I nstructi ons: To reduce the ri sk offi re,el ectri c shock and/ ori njuryto persons,al ways fol l ow these basi c safetyprecauti ons when usi ng yourtel ephone equipm ent. 1. Read,understand,and follow allinstructions. 2. Unplug this telephone from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Ifnecessary,use a soft cloth lightly m oistened with a m ild detergent solution. 3.
I MP OR TAN T IN FOR MAT ION SPECIAL FEATURES Your new Multi-handset Cordl ess System i s designed and engineered to exacting standards forrel iability,long life,and outstandi ng perform ance. Note: Charge the batteryforabout15 hours before ini ti aluse. • • • • • • • • • • • • • • • • • 2.4 GHzDigitalDSS Cordl ess Phone Multiple handset s capabil ity,support s up to 8 handsets Handset-to-Handsettwo-wayintercom independentofthe base unit.
I MP OR TAN T IN FOR MAT ION QUICK REFERENCE Task 1 Adjust receivervolum e 2 Make call Steps The handset and the base unit have 4 receiverlevels which can be adjusted during offhook. 1. 2. 3. 3 4 Answercal l Redi allast num ber Dialfrom rediall i st 28 Press [Talk] or[Spk.] on the handset or 26 press [Speakerphone] on the base unit and li sten fordialtone. Dialnum ber(Form em orydialfeature, see related reference.
I MP OR TAN T IN FOR MAT ION QUICK REFERENCE 9 Task Add new num berto Phone Book 1. Press [DIR.]. 3. Press [O.K.] and input nam e. 2. 4. 10 Store Cal lerID num berto 1. 11 1. Press [DIR.]. Page from base to al l handsets 16 Di spl ayCallerID num ber. Dialfrom Phone Book 13 15 Press [SAVE] to store. 2. Switch to waiting call 14 Press [SAVE] and input num ber. Phone Book 12 Intercom between handsets Press [SAVE] to store the num berto Phone Book. 2.
P R EPAR AT ION Yournew tel ephone i ncl udes the highestquali ty Ni Cd (Ni ckelCadm i um )batteri es avai l abl e. Fol lowi ng these si m pl ei nstructi ons can signi fi cantl yi m prove your operati onalresul ts. CHARGING THE BATTERY PACK Charge allthe batterypack forat least 15 hours priorto connecting to the tel ephone l ine.
P R EPAR AT ION LOCATION OF CONTROLS Handset MessageW ai ti ng /New CallLi ght (a)Flash rapi dlywhen ringing. (b)Flash regularlyifyou have m essage in yourvoicem ailornew CallerID in CallLog. (c)Light when the handset i s in use. Speakerphone Li ght Light when speakerphone i s in use. HeadsetJack The headset jack all ows the use ofa headset with a standard 2.5m m pl ug. Di alPad The num eric keys are used i n the conventionalm annerfordial ling.
P R EPAR AT ION Di al7 / Mute Key (a)W hile reviewi ng the CallID Record,press [Dial7] to diala CallBack i n 7-di git form at. (b)W hile on a call,press [Mute] to m ute the m icrophone forprivacy. Di al10 / Redi al/ Pause Key (a)W hile reviewi ng the CallID Record,press [Dial10] to diala CallBack in 10-digit form at. (b)W hile off-hook,press [Redial] to recalland dialthe last phone num berdi aled. (c)W hile on-hook,press [Redial] to access the Redi alLi st.
P R EPAR AT ION Base Uni t MessageW ai ti ng / New Cal lLi ght/ In-Use Indi cator (a)Flash when ringing,orifyou have m essage in yourvoicem ailornew Cal lerID in Call Log. (b)Light wheneverthi s phone,oranyothertelephone on the l ine,i s being used. Speakerphone Li ght Light when speakerphone i s in use. Charge Light Light when handset i s on the cradle and being charged. Spare BatteryLi ght Light when the spare batteryis in the charging com partm ent.
P R EPAR AT ION Di al10 / Redi al/ Pause Key (a)W hile reviewi ng the CallID Record,press [Dial10] to diala CallBack in 10-digit form at. (b)W hile off-hook,press [Redial] to recalland dialthe last phone num berdi aled. (c)W hile on-hook,press [Redial] to access the Redi alLi st. Usi ng [▼ ] or[▲ ] to select the desired num berand press [Speakerphone] to dialit out. (d)Press the keyduring Pre-di alorPhone book num berentrywillentera 2-second pause i nto a dialing sequence with “P”appears on the di splay.
G ET T IN G STAR T ED Check to be sure the fol lowing item s com e with the phone. • Base Unit • Two Handsets with Belt Clips • Recharge Cradle • Three BatteryPacks • Long Telephone Line Cord • Short Telephone Line Cord forW al lMounting • AC Adapter • W all-Mounting Bracket • Owner’ s Manual CHOOSE THE BEST LOCATION Call s are transm itted between the base unit and the handset,or between handset & handset, by using wireless radi o waves.
G ET T IN G STAR T ED CONNECTING THE BASE UNIT 1. 2. 3. 4. 5. Plug one end ofthe telephone li ne cord into the j ack on the back ofthe base unit and pl ug the otherend ofthi s cord into the m odulartel ephone wallj ack. Press the l ine cord into the slot provided on the back ofthe telephone. Plug the AC adapter into the 9V DC jack on the base and the other end into a standard 120V AC walloutlet. Press the cord in the slot on the housi ng to prevent the cord from pulli ng loose.
G ET T IN G STAR T ED W ALLMOUNTING BASE UNIT The base unit can be m ounted on a wallphone plate byusing the suppli ed wall-m ounti ng bracket. 1. 2. 3. 4. 5. 6. Bring the barrelpl ug ofthe AC adapterthrough the rectangularopeni ng on the bottom ofthe wall-m ounti ng bracket. Plug the adapter’ s barrelplug i nto the 9V DC jack on the base unit and press the cord in the slot provided. Plug one end ofthe short telephone li ne cord into the TEL. LINE jack at the bottom ofthe base unit.
GET T IN G STAR T E D REGISTRATION OF HANDSET The first regi stered handset willbe autom atically assigned as HS-1 to the base unit. W hen additionalhandsets are regi stered to the system ,theywillbe assigned extensi on num bers i n the following sequence: HS-2,HS-3,and up to HS-8. On the Base Uni t: REGISTRATION O.K. Press [MENU] and “REGISTRATION”appears on the di spl ay. EXIT WAITING REGISTER Press [O.K.] and “W AITING REGISTER”is displayed. You are now readyto regi steryourhandset.
GET T IN G STAR T E D The handsetwillreturn to “REGISTRATION”after2 seconds. Press [EXIT]to end the regi stration. NO NEW CALL HS-1 10:00AM 1/01 SAVE MENU SERVICE DIR. DI AL V.M. CHOOSE THE DIALING MODE Ifyourhom e i s equi pped with a touchtone dialing system ,the phone wi llbe readyto use as soon as the battery is charged. Ifyou have a pul se (rotary)di ali ng system ,you wi ll need to setthe dialing m ode as fol lows: 1. Press [MENU]. 2. Press [▼ ]or[▲ ]to select“DIAL MODE”. 3. Press [O.K.].
M E N U S E T T IN GS The phone offers an extensive range offunctions which are grouped in m enus. You can personalize yourphone bypressing the Menu keyand using review keys to scroll through the options. STRUCTURE AND OPTIONS The m enu settings have two levels. There are twelve item s on the handsetand el even item s on the base unitin the firstleveland the num berofitem s i n the second level depends on the calli ng item s ofthe firstlevel.
M E N U S E T T IN GS M enu Available on base unit Available on handset FirstLevel Second Level Rem arks 6 Yes Yes Contrast 0-8 Levels Thissetsthe LCD contrast. The defaultis 5 7 Yes Yes CallW aiting ID O ption O n /O ff Thissetsto activate or deactivate CallW aiting ID O ptionsoperation. The defaultisO n. 8 Yes Yes PBX M ode PBX Prefix Thissetsto add the PBX Prefixnum berfor outgoing calls. 9 Yes Yes New Call Lam p O n /O ff Thissetsthe New Call Lam p to be on oroff.
M E N U S E T T IN GS MENU FUNCTIONS Regi strati on You m ustfirstsetthe base unitto regi stration m ode pri orto addi ng ordeleting handset s. Sim plypress [MENU]on the base unitto sel ect“Regi strati on”then press [O.K.]to confirm .The base unitwillreturn to standbym ode ifno handsetregi stration takes place within 25 seconds. To add a handsetto a desi red base REGISTRATION HS_ _ O.K. Press [MENU]on the handsetduring standby. Using [▼ ]or[▲ ]to select“REGISTRATION”. Press [O.K.
ME N U S E T T IN GS To del ete al lhandsets from the base DEL ALL HANDSET In the second level,using [▼ ]or[▲ ]to select“DEL ALL HANDSET”. Press [O.K.]to de-registerallhandset s from the base. O.K. EXI T DEL ALL HS OK! “DEL ALL HS OK!”appears on the di splayto confirm globalde-regi strati on. The handsetreturns to “REGISTRATION”after2 seconds. Press [EXIT]to return and “HS_ _”i s di splayed.
ME N U S E T T IN GS Using [▼]or [▲ ]to s elect the des ired language, then ENGLISH? press [SAVE]to confirm . Press [EXIT]to return. EXI T SAVE Ri ngerSound RINGER SOUND O.K. EXIT Press [MENU]. Using [▼]or [▲ ]to s elect “RINGER SOUND”. Press [O.K.]to enter and the current ringer tone will be played for a few s econds . TONE:1 (1,2,3?) Press [1], [2]or [3]to s elect the ringing tone for an EXI T incom ing call. The corres ponding ringer tone will be played for a few s econds .
ME N U S E T T IN GS Using [▼]or [▲ ]to s elect “AUTO MODE”or “M ANUAL AUTO MODE MODE”. Press [SAVE]to confirm , and then press [EXIT]to return. EXIT SAVE Contrast CONTRAST O.K. Press [MENU]. Using [▼]or [▲ ]to s elect “CONTRAST”. Press [O.K.]to enter into the s election. EXIT Using [▼]or [▲ ]to adjus t the contras t level. LEVEL:05 Press [SAVE]to confirm , and then press [EXIT]to return. EXI T SAVE Cal lW ai ti ng ID Options CW ID OPTION O.K. Press [MENU].
ME N U S E T T IN GS PBX Mode Ifyou us e an in-hous e phone s ys tem , you m ayhave to dial an external access code before placing an outgoing call. Follow the s teps below and enter that code in the PBX PREFIX field. This code will then be added to all s tored num bers when dialing out. Press [MENU]. PBX MODE O.K. Using [▼]or [▲ ]to s elect “PBX MODE”. Press [O.K.]to enter into the s election. EXIT PBX PREFIX:_ EXIT Using [▼]or [▲ ]to enter a digit number for outgoing calls .
Ti m e and Date Setti ng SET DATE/TIME 10:05 AM 05/03 O.K. Press [MENU]. Using [▼]or [▲ ]to s elect “SET DATE/TIME”. Press [O.K.]to enter into the s election. EXI T ENTER DATE/TIME: Press [▼]or [▲ ]to s et tim e and date. Press [O.K.]to 10:05AM 03/25 O.K. SAVE EXI T m ove from hour to minute, to AM/PM, from m onth to day. Press [▼]or [▲ ]to change the dis played s etting. Press [SAVE]to confirm , and then press [EXIT]to return.
ME N U S E T T IN GS Last Call Timer LAST CALL TIMER Press [MENU]. Using [▼ ]or[▲ ]to displ ay“LAST C ALL TIMER”. Press [EXIT]to return. 00-06-25 EXI T Message W aiting Lamp This m ode i s available onlywhen there i s new or non-viewed m essage in yourvoicem ail. MESSAGES HS-1 10:05AM 05/03 SAVE MENU SERVICE DIR. DIALV.M. DELETE MESSAGE? O.K. EXI T Press [MENU]. Using [▼ ]or[▲ ]to select“DELETE MESSAGE?”. Press [O.K.]to confirm clearing ofthe m essage waiting lam p.
BAS IC O PE RAT IO N TO MAKE A CALL Dial Direct Press [Speakerphone]on the base unitor[Talk]/[Spk.] on the handsetand l i sten forthe dialtone. The “In-Use” indicatoron the base unitwillbe turned ON. PHONE ON SERVICE DIR. PHONE ON 00:01 DI AL V.M. 1234568 3W AY Use the keypad to di althe phone num ber. The phone num berwillbe shown on the di spl ayalong with the call tim er. Press [Speakerphone]on the base unitor [OFF]on the handsetto end yourcall.
BAS IC O PE RAT IO N TO REDIAL A CALL Redial Last Number Press [Speakerphone]on the base unitor[Talk]/[Spk.] on the handsetand l i sten forthe dialtone. PHONE ON SERVICE DIR. PHONE ON 00:01 DI AL V.M. 1234568 Press [Redial]to dialthe lastdi aled num ber. 3W AY SERVICE Dial from the Redial List The Redi alLi ststores up to 20 lastdialed outphone num bers,each one can be up to 32 digit s. REDIAL USE↓=VIEW In Standby Mode,press [Redial]once to access the redialli st.
BAS IC O PE RAT IO N ADJUSTING HANDSET VOLUM E There are 4 receiverlevels in handset. Itcan be adjusted bypressing [▼ ]or[▲ ] during talkm ode. (Also applyto handsetand base speakerphone volum e adjust m ent when the phone i s in Speakerphone m ode.) USING HANDSET SPEAKERPHONE W hile on a call,press [Spk.]to turn the speakerphone ON and OFF. The Speakerphone Li ghtcom es ON when the speakerphone i s in use. PAGING FROM BASE TO HANDSET To locate the handsetwhil e iti s noton the base unit,press [Int.
ADVAN CE D O PE RAT IO N FLASH Call W aiting 1. 2. Use [Flash] for accessing Call W aiting service. For exam ple, if you receive a second callduring yourinitialcall,press [Flash]to putthe firstcallon hold to answer the waiting call. Afteryou finish a private talk with the second cal ler,press [Flash]to return to the first caller. Note:Ifyou also have conference Call ing service,press [Flash]to al low the firstcal ler enterinto a conference call. Conference Calling 1. 2.
ADVAN CE D O PE RAT IO N DIAL VOICE M AI L Ifyou have subscribed to the Voice Mailand Message W aiting Indicatorservices,you can access yourvoice m ai lsystem by pressing [DIAL V.M.]. To use thi s feature,you m ustfirstprogram yourvoicem ailnum ber(yourtelephone num ber)i nto the handsetand base unit. Program your own Voicemail access number DIAL VOICE MAIL ----------EDI T Press the softkey[DIAL V.M.]. Press the softkey[EDIT],you willthen be prom pted to “ENTER NUMBER :”.
CALLE R ID O PE RAT IO N ABOUT CALLER IDENTIFICATI ON This tel ephone has a Cal lerID feature thatworks with Call erID service provided by your localtel ephone com pany. There is a fee forthi s service,and itm aynotbe available i n allareas. Thi s phone can provide inform ati on onlyifboth you and the callerare in areas offeri ng Cal lerID service,and ifboth telephone com panies use com pati ble equi pm ent. Depending on yourservice,you willbe able to see the num ber,orthe nam e and num berofyourcaller.
C AL LE R ID OP E R AT ION Delete Caller ID List 50 CALLS ↓=VIEW EXIT DELETE D record: ↓ To delete an individual Caller I W hile reviewi ng the CallerID Li st,press [DELETE]to erase the di splayed record from the l i st. JOHN SMITH 123-123-4568 10:00AM 1/01 #01 X1 EXIT To delete all Caller I D records: Press [▼ ]or[▲ ]duri ng standbym ode to enteri nto Caller ID Listdefaultpage. Press [DELETE]and “DELETE ALL?” is di splayed,then press [O.K.]to confirm del etion.
C AL LE R ID OP E R AT ION ↓ Forwarded Call Ifthe callwas forwarded from anothernum berthrough 123-123-4568 AM the callforwarding service provided bythe telephone 10:00 1/01 #01 X1 com pany,the icon willappearon the screen with the EXIT DELETE callinform ation. JOHN SMITH SAVE ↓ RepeatCall Ifa callis received from the sam e phone num berm ore 123-123-4568 AM 10:00 1/01 #01 X6 than once,the num beroftim es repeated wi llbe shown on the di splay.
C AL LE R ID OP E R AT ION CALL W AI TI NG ID OPTIONS Ifyou have subscribed the CallW aiti ng and Cal lW aiting ID Options from yourlocal telephone com pany,you willheara Cal lW aiti ng tone when a new callcom es in while you are talking. You can eitheralternate between call s ordi sposition the call.
C AL LE R ID OP E R AT ION Call W aiting ID Option:JOI N JOHN SMITH 123-123-4568 10:00AM 1/01 D R OP L1 X1 If[JOIN]softkey is pressed,“CONFERENCE”wi llbe di spl ayed fora shortwhile and then the waiting partyis being added to the originalcallas a 3-parties conference call. Afterthe 3-parties conference cal l,you m ayselectto drop a l ine and retain the other: DROPPED #1 • 00:05 • 3W AY To drop the firs t caller (the original call), press [DROP] s oftkeyand “DROPPED #1”will be dis played.
P H ON E B OOK D IR E CT ORY Your phone has a Phone Book Directoryfor s toring up to 50 im portant nam es and telephone num bers . Each m em orycan s tore 32 digits and 15 characters . You can edit the Phone Book Directoryrecords , but not the Caller ID Lis t records . The Directory records are s aved in alphabetical order. The Phone Book Directorycan be access ed bypress ing [DIR.] during s tandbym ode.
P H ON E B OOK D IR E CT ORY Add a New Number/Name Press [DIR.]during standbym ode.“NO ITEM”appears if no records i n the directory,or“20 ITEMS ↓=VIEW ” appears ifthere i s 20 records in the directory. Ifthe m em orylocations are ful l,the m essage “LIST FULL”wi ll appearand yourrequestis rejected. NO ITEM EXIT SAVE USE SAVE=CREATE After3 seconds,“USE SAVE=CREATE”appears on the di spl ay. EXIT SAVE ENTER NUMBER: 12312_ O.K. EXI T DELETE Press [SAVE].Enterthe num ber. Tip:1.
P H ON E B OOK D IR E CT ORY Entering Alphanumeric Characters: Each num eric keyis assigned a setofletters and sym bol s.Press the correspondi ng num beruntilthe desired l etteris di spl ayed. Num eric: 1 2 3 4 5 6 7 8 9 0 Characters: Space A,B,C D,E,F G,H,I J,K,L M,N,O P,Q,R,S T,U,V W ,X,Y,Z Adding Special Symbols You can also use the [*]and [#]to sel ectthe following specialsym bol si n the nam e field. ∗ + , - . /@ :;< = > ?{¦}~ [ \ ]^ _`!″ # $ % & ´ ( ) 38
P H ON E B OOK D IR E CT ORY EDITING A PHONE BOOK NUMBER ↓ Selectthe record you wantto edit. The recorded nam e willbe played back i nstead ifthere was call ernam e being recorded. JOHN SMITH 1231234568 EDIT O.K. EXI T DELETE SAVE PLAYING 1231234568 EDIT O.K. EXI T DELETE ENTER NUMBER: 1231234568_ O.K. EXIT DELETE JOHN SMITH_ 1231234567 EXIT SAVE JOHNNY SMITH 1231234567 EDIT O.K.
P H ON E B OOK D IR E CT ORY DELETING ALL PHONE BOOK DIRECTORY RECORDS 20 ITEM ↓=VIEW EXIT SAVE DELETE ALL? O.K. Press [DIR.]to enterinto Phone Book Directorydefault page. DELETE Press [DELETE]and “DELETE ALL?”is di splayed. To confirm the del etion ofal lrecords,press [O.K.]. To exit withoutdeleting,press [EXIT]. EXI T DIALING FROM PHONE BOOK DIRECTORY During standbym ode (on hook oroff-hook),press [DIR.]and find the entry you wantto call. Press [O.K.]to callthe num ber.
M U LT I- H AN D SET OP E R AT ION Yournew telephone provides a m ultiple handsetcapabi litywhich supports up to 8 handsets. Each additionalhandsetcom es with a chargeryou can pl ug into any electricaloutlet. No extra phone jack i s required. Itis possible to m ake an i nternalcallbetween two handsets whil e anotherhandseti s engaging the externalline INTERCOM CY-368D base unitcan support4 groups ofintercom conversation si m ultaneouslyifyou have 8 handset s in yoursystem .
M U LT I- H AN D SET OP E R AT ION INVALID NUMBER Ifyou are entering an unregi stered handsetnum ber, “INVALID NUMBER”is displayand you need to repeat the above step agai n. EXIT TRANSFER FROM BS The handsetyou called rings and “TRANSFER FROM BS”on the di spl ay. Press [Talk]or[Spk.]on the called handset,the callwi llbe connected autom atically. Ifthe handsetyou called does notanswerin 20 seconds, the unanswered callwillri ng back to you agai n. EXIT Press [Talk]or[Spk.
OPT ION A L FE AT U R E S D IAL L IS T You phone has been pre-program m ed atthe factorywith an optionalservices di alli st. DISPLAY 411 RPT DIAL FW D ON FW D OFF CALL RTN 3W AY CLASS SERVICE Help Hotline RepeatDial ing Activate CallForwardi ng CancelCal lForwarding Activate CallReturn Three W ayCalling DIAL CODE 1411 66 72# 73# 69 Flash Note: These optionalservices,except1411,are accessibl e onlyifyou subscribe from your localtel ephone com pany.
OPT ION A L FE AT U R E S D IAL L IS T 3-W AY CALLI NG PHONE ON 00:05 1234568 3W AY While on a call, press [3WAY] to acces s Three Way Calling s ervice. The s ys tem will dial out a long Flas h to put the initial call on hold and obtain a new dial tone to m ake a second call. SERVICE PHONE ON 00:30 3456812 Key in the phone num ber ofthe second party. After the s econd call is connected, press [3WAY] to add the firs t caller into the conference call.
AD D IT ION A L IN FOR M AT ION CAPACI TY Mem ory The Caller ID Lis t:50 m em ory locations ;24 digits and 15 characters per location. Phone Book Directory:50 m em ory locations ;32 digits and 15 characters per location. Voice Announce Caller Nam e:25 m em ory locations ;3 s econds per location. Redial Lis t:20 m em ory locations ;32 digits per location. Cal lRepeatNum ber The Call Repeat num ber is s even m axim um .
T R OU BLE S HOOT IN G Before calling for s ervice, please check this lis t ofthe m os t com m on problem s . Probl em The phone does not work Check Are the LINE CORD and AC adapter connected properly? Is the hands et too far away from the bas e unit? Does the battery pack becom e weak? Charge the battery on the bas e unit for about 15 hours . The phone does not ring Check the RINGER s etting.
CAR E AN D M A IN T E N AN CE The following s ugges tions will help you care for the s ys tem s o you can enj oy it for years . Keep the s ys tem dry.Ifit gets wet, wipe it dry im m ediately.Liquids m ight contain m inerals that can corrode the electronic circuits . Use and s tore the s ys tem only in nor m al tem perature environm ents . Tem perature extrem es can shorten the life of electronic devices , and dis tort or m elt plas tic parts . Handle the s ys tem gently and carefully.
FCC R E Q U IR E M E N T S This equipm ent com plies with Part 68 ofFCC rules and the requirem ents adopted by the ACTA.On the b ottom ofthis equipm ent is a label that contains , am ong other inform ation, a product identifier in the form at US:CACWI00B368001. Ifreques ted, this num ber m us t be provided to the telephone com pany. The REN is us ed to determ ine the num ber of devices that m ay be connected to a telephone line.
express ly approved by the party res pons ible for its com pliance could void the us er’ s authority to operate the equipm ent. This equipm ent should not be us ed on coin telephone lines . Connection to party line s ervices are subj ect to s tate tariffs . Iftrouble is experienced, dis connect this equipm ent from the telephone line to determ ine ifit is caus ing the m alfunction. Ifthe equipm ent is determ ined to be m alfunctioning, its use s hould be dis continued until the problem has been corrected.
CY-368B-SB 20041014 50
