R3572-A-IN Module USB Manual RT3572 RT3572-A-IN WLAN Dual802.11N Band 802.11 a/b/g/n module Wireless Dual-band USB Module User Manual Rev 0.
R3572-A-IN Module USB Manual Table of Conetents Introduction Hardware installation Setting up Wireless Network by WZC service 2
R3572-A-IN Module USB Manual Chapter 1 Introduction Thank you for using the Wireless USB Module. RT3572-A-IN is a dual-band, quad-mode wireless network adapter that works on all the frequencies allocated for WLAN operation everywhere in the world. It is in compliance with the Draft IEEE802.11n standard in a 2x2 MIMO configuration. It also complies with the IEEE 802.11a, 802.11g, and 802.11b standards.
R3572-A-IN Module USB Manual Feature z z z z z z z z z z z z z z USB interface. Draft IEEE 802.11n compatible. Backward compatible with IEEE 802.11a/b/g standard. Wire-free access to networked resources from anywhere beyond the desktop. Delivers data rates up to 300 Mbps. 802.
R3572-A-IN Module USB Manual Chapter 2 This chapter covers how to installing the Wireless USB Module in your embedded system. Hardware description The Wireless USB Module has a standard USB interface for attaching to the 2x5 pin header (pitch=1.27mm) on embedded system. And this module has IPEX connectors to connect to external antenna.
R3572-A-IN Module USB Manual Figure 1: USB module outlook 6
R3572-A-IN Module USB Manual Chapter 3 The Wireless Zero Configuration (WZC) service, available in Windows system, dynamically selects the wireless network to which attempts connection, based either on your preferences or on default settings. 3.1 Wireless Networks tab On the Wireless Networks tab, users are able to view and configure the following: z Use Windows to configure my wireless network settings: Enable this check box when you want to use the WZC service to configure your wireless settings.
R3572-A-IN Module USB Manual z Available networks: The list of wireless networks that are within the range of wireless adapter. To view or change the configuration of a specific wireless network and add it to the list of preferred networks, click it in the list of available networks, and then click Configure. To force the wireless adapter to initiate a new scan of wireless networks within range, please click Refresh.
R3572-A-IN Module USB Manual networks list, click Add. To remove a wireless network, click Remove. To configure the settings of a wireless network to which connected, click Properties. Advanced: To configure advanced wireless settings are independent of the wireless networks to which connected, click Advanced.
R3572-A-IN Module USB Manual preferred list (by using the Automatically connect to non-preferred networks setting, which is disabled by default). 3.2 Messages in notification area To enable the check box of Show icon in notification area when connected, if there is a condition that requires either user notification or intervention, the WZC service prompts you with a message in the notification area.
R3572-A-IN Module USB Manual 11
R3572-A-IN Module USB Manual ( Wireless Network Connection Status: User can check Wireless Network Connection Status, including which wireless network connected, data rate, signal strength and which IP the wireless adapter obtains.
R3572-A-IN Module USB Manual Wireless Network Connection: The list of wireless networks that are within the range of wireless adapter. Users also can select the network you want to connect and click Connect. If it is not a unsecured wireless network, a network key is required, user has to key-in WEP/WPA key then click Connect again.
R3572-A-IN Module USB Manual U.S. Regulatory Wireless Notice Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
