MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card User Manual Rev 1.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Important Information Please read the information below before using the WM600-B-LO 11b/g wireless PCI- Express card on your system. What’s New The latest generation PCI (Peripheral Component Interconnect) bus architecture called PCI Express, uses a 2.5- GHz serial Input/Output structure for higher bandwidth and better scalability than its previous architectures. . Features • PCI Express PCIe interface. • X1-lane 2.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Before Using the WM600-B-LO, check to be sure your system meets the following minimum requirements: z Available PCI-Express card slot z 64 MB of System Memory z 150 MHz or faster processor z The most recent BIOS version for your system Hardware Driver Compatability To ensure optimal performance, it is recommended that you download the latest hardware drivers for all your particular adapters from the manufacturer's web site.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Complies with IEEE802.11g, IEEE802.11b standards, Supports WPA/WPA2 data security, authentication, TKIP/AES encryption, 64/128/152-bit WEP encryption Supports 54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps wireless LAN data transfer rates. Provide 32-bit PCI E interface. Supports Ad-Hoc and Infrastructure modes Supports roaming between access points when configured in Infrastructure mode Ease to configure and provides monitoring information.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card The new Connect to a network dialog box is a redesigned version of the Choose a wireless network dialog box in Windows XP with Service Pack 2 (SP2). This new dialog also supports virtual private network (VPN) and dial-up connections (including Connection Manager and Point-to-Point Protocol over Ethernet [PPPoE]). In Show, you can select the following: • All Wireless, dial-up, and VPN connections. • Wireless Only wireless connections.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Internet Ad Hoc mode: PC use wireless to connect to each otherb Ad Hoc To connect to a wireless network that is listed in the Connect to a network dialog box, double-click the network name or click the network name and then click Connect. For a non-broadcast network, you will be prompted to type the wireless network name. If the connection attempt is not successful, use Windows Network Diagnostics to diagnose the problem and suggest a solution.
MW600-B-LO Wireless 802.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Note If the Manually connect to a wireless network option is not present in the Choose a connection option dialog box, make sure that your wireless network adapter appears in the Network Connections folder as a wireless connection and is enabled. If your wireless network adapter appears in the Network Connections folder as a wired connection, ensure that you have installed the latest driver for your adapter that is designed for Windows Vista.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card • WPA2-Enterprise WPA2 with IEEE 802.1X authentication. • WPA-Enterprise WPA with IEEE 802.1X authentication. • 802.1x IEEE 802.1X authentication with WEP (also known as dynamic WEP). The choices listed depend on the capabilities of your wireless network adapter that are reported to Windows. The shared key authentication method is not listed. Microsoft strongly discourages its use because it provides weak security for your wireless network.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card • Connect even if the network is not broadcasting Specifies whether Windows should attempt to connect even if the wireless network is not broadcasting its name. This will cause Windows Vista to send Probe Request frames to locate the wireless network. These probe request frames can be used by malicious users to determine the name of the non-broadcast network.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card From the Connection tab, you can view the wireless network's name, SSID, and network type (either Access point for infrastructure mode networks or Computer-to-computer for ad hoc mode networks).
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card On the Security tab, you can specify the following security types: • No authentication (Open) • Shared Shared key authentication. The Security tab is the only location where you can configure shared key authentication because its use is highly discouraged. • WPA2-Personal • WPA-Personal • WPA2-Enterprise • WPA-Enterprise • 802.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card WPA2-Enterprise, or 802.1x as your security type, you must configure the following (as shown in the previous figure): • Choose a network authentication method Select an Extensible Authentication Protocol (EAP) method and click Settings to configure the EAP type as needed. • Cache user information for subsequent connections to this network Specifies that when the user logs off, the user credential data is removed from the registry.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card After you have configured your wireless networks, you can manage them from the Manage Wireless Networks dialog box. To display the Manage Wireless Networks dialog box, do the following: 1. Click Start, right-click Network, and then click Properties. 2. In the task list of the Network and Sharing Center dialog box, click Manage wireless networks. The following figure shows an example.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card Appendix A Specifications Product Name Wireless 802. 11b/g wireless PCI-E Adapter Card Interface PCI Express® Rev 1.1, X1-lane 2.5Gbps PCIe Motherboard Slot Network Standard IEEE802.11g/b COMPLIANT Data Rate 54Mbps, automatic fallback to 48, 36, 24,18,12,9 and 6 Mbps 802.11g---- 54, 48, 36,24,18,12,9,6Mbps (OFDM) Modulation 802.11b---- CCK (11Mbps, 5.
MW600-B-LO Wireless 802. 11b/g wireless PCI-E Adapter Card -70 dBm @ 54M (OFDM, 10% PER) Receiver Sensitivity -87 dBm @ 6M (OFDM, 10% PER) -84 dBm @ 11M (CCK, 8% PER) Power Consumption TX power consumption: <480 mA RX power consumption: <470 mA WEP Support 64/128 bit encryption Support OS Operating Temperature Microsoft Windows XP, Vista premium/basic English/Chinese version. 0 to 60 ℃ Humidity 20% to 95% Non-condensing Dimensions (mm) (W) 19mm × (D) 167.65mm × (H) 68.
