INSTRUCTION MANUAL Components Main body 01 Handle(cutter) 01 Accessories 01 Methods of use How to use the product 02 Status explanation 04 How to charge 05 Checklist before use and precautions 05 Product management Replacement of blade and replacement of collet 06 About blade and collet 07 Safety cautions Warnings and cautions 08 Custom service Compensation for damage 10 Product and battery standards 10 Self-diagnosis Before requesting repair 11 About us What materials do you want to cut? 12 Crowdfun
p.1 01 Components Main body Remaining battery LED Power button Handle (Cutter) Cable Main body Belt clip Leg * The battery-pack is built-in. Handle (Cutter) Power switch Transducer horn (Vibrator) Blade Accessories Blade(40p) Charger * Check for the following components. 02 Methods of use How to use the product 03 Methods of use 01. Pull the handle out from the inside of the main body. 02. Press the main power button for 1 to 2 seconds to turn the LED setting into stand-by mode.
handle indicates that the cutter is vibrating. 04. When used for more than 10 minutes, the Wondercutter will stop operating and return to Standby Mode to allow cooling. The green LED on the handle is off while cooling. The cooling condition is call the Stationary State. While in the Stationary State, the Wondercutter can be turned on again by holding the button on the handle. However, to ensure proper performance, allow the Wondercutter to cool for several minutes before returning to operation.
power will provide maximum performance. - The Wondercutter will provide maximum performance when the charger is plugging into an outlet. - If the device is not fully charged, the cutting power will be reduced. - A loose setscrew will cause the Wondercutter to overheat and it may eventually cause damage. Properly tighten the setscrew for safety. - Properly attached the Wondercutter when carrying around the waste for mobile use. - Follow the instructions to correctly install the blade to the handle.
on, retighten the setscrew and reset. 4. Once the setscrew is fixed, turn the power of the main body on and press the handle button on to check that the Wondercutter is operational. * If the Wondercutter is still not operational, clean the inside of transducer horn by following the steps below. Also, cleaning or replacing the collet or the blade can return the Wondercutter to full use. 1. Turn the main power off. 2. Remove the collect and the blade. Then clean the inside of transducer horn with q tips. 3.
- Change the hex wrench if signs of wear. - Ask for the manufacturer's help when the setscrew does not fall out. - When the blade has been changed while the vibrator produces heat, the setscrew may become loose when the temperature goes down. Make sure that the setscrew is correctly tightened before using the product. Blade fixing screw Blade Collet 08 Safety Cautions Warning If the instructions are not correctly followed, death or serious injury can occur.
- Places with high temperature or inflammable objects. Places with dust and generating corrosive gas. Places with high vibrations and impacts. Wet and humid places. Be careful not to drop the blade while moving the product. Depending on what type of object is cut, it can cause substance or gas that affect the human body. Check before using. Cautions - Do not put spray on the main body, cutter, and charger. This may cause deterioration or breakdown of the plastic or paint.
Product and battery standards Model Number WC40000F25W Oscillation Frequency 40 kHz Body Dimensions 175 x 102 x 62 mm Handle Dimensions Ø 28 x 104 mm Body Weight Approx. 670 g Handle Weight Approx. 85 g Max. Power Consumption 30W Charger INPUT: AC100~240V, 50/60Hz, 1.5A MAX Ambient Condition 5 ~ 35 ℃ Use Time Approx. 1 hr 30 min. cycled Type Lithium-Ion battery Nominal Capacity Rated Voltage Battery Charging Time 2600 mAh 11.1 V Approx.
contaminated or has its shape changed? Is there any foreign substance on the blade or at the end of the vibrator? Is a supplied blade being used? The handle gets hot. Was the product used for a long time? Is too much pressure being held on the blade? Is the blade and setscrew correctly fixed? Clean the inner parts of blade, collet, setscrew, and the end of the vibrator. After 10 minutes of use the product automatically turns to Stand-by Mode.
FELT EVA FOAM PAPERBOARD RUBBER LEATHER PMMA ABS The thickness that can be cut is different depending on the materials.