How-To Guide

EXTERIOR
LED GRILLE LIGHT KIT
App-Controlled for your vehicle
Smart Lighting
BEFORE INSTALLATION
It is recommended that you download the App,
connect and test your LED lighting kit before
installation and read all instructions carefully.
Model: 23192 FCC ID: 2ADMQ-23191-23192
®
CUSTOM ACCESSORIES, INC.,
RICHMOND, IL 60071, USA
MADE IN CHINA © 01_2021 CA
3. To install your light strips, clean your installation
surface thoroughly with alcohol and allow to dry
before installation. It is recommended that the
temperature for installation is 65-90° F (18-32° C).
4. Align arrows to connect LED strips to wire harness.
Push connectors together tightly.
5. Peel off the 3M™ tape backer on your lights strips
and carefully apply to the desired area. Let adhesive
set for at least one hour. Next, secure the light strips
with the included plastic clips and metal screws. Drill
a pilot hole using a 1/16” bit before inserting the
screws. Tuck and secure all wires with included
cable ties.
6. Open the package and find the direct wire harness.
Connect the direct wire harness to the control box.
7. Run the wires toward a 12V power source (For
example, a fuse box or light switch). The circuit
chosen must be able to supply 3 Amps.
ONE YEAR WARRANTY
We guarantee this product to be free of defects in material and
workmanship for a period of one year from the date of purchase. If a
defect in material or workmanship occurs, call Custom Accessories
customer service at [phone] for instructions on how to
have it replaced or repaired free of charge.
PROOF OF PURCHASE OR RECEIPTS MUST BE PROVIDED
FOR ANY/ALL REPLACED OR REPAIRED ITEMS.
This guarantee does not cover normal damage to the product
that is not the result of a defect in materials or workmanship such as,
for example, normal wear and tear or damage resulting from an
accident. Shipment of any product back to Custom Accessories is at
the consumer’s expense. Custom Accessories, Inc. limits its liability
only to the replacement of its products, not incidental or
consequential damages to other property. Some states do not
allow the exclusion or limitation of incidental or consequential
damages. This guarantee gives you specific legal rights and you
may also have other rights which vary from state to state.
FCC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation. NOTE: This equipment has
been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
product. This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located
or operated in conjunction with any other antenna or
transmitter.
3' (91.4cm) Wire
18 Screws
Kit includes:
2x End Caps
3' (91.4cm) Wire
A registered trademark of Bluetooth SIG, Inc
Smart Lighting
and download the App scan
the QR code with your
smartphone!
To learn more about
Download the
“LED INNOV”
App
TM
Visit our website at
ww w.causa.com
Customer Service:
1- 8 0 0 -962- 6 676
www.causa.com/led-innovation
WARNING
Do NOT bend in excess of a 90° or crease when
installing. Will cause permanent damage to the
LED Light strip.
For additional light strips please contact
our customer service center for additional details.
Customer Service:
1- 8 0 0 -962- 6 676
For FCC matters please contact:
Custom Accessories Inc., 5900 Ami Drive, Richmond, IL 60071
Ph. # [phone]
FCC RF Radiation Exposure Statement
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
8 Clear mounting clips
To replace fuse, remove fuse and replace with like amperage.
Para cambiar el fusible, saque el fusible y reemplácelo con
uno de amperaje similar.
12v - 3 amp maximum
12v - 3 máximo de amperio
Mini blade fuse
Mini fusible De cuchilla
36”
23192
4 x 4' (121.9cm) Extension Wire4 x 9" (121.9cm) LED Light Strips
3M™ TAPE
per strip
2 - 2" 3M™ TAPE
per strip
1' (30.48cm) Wire
10 Cable Ties
INSTALLATION
1. Begin by laying out your new lighting system in the
grille of your vehicle. Place your LED strip lights where
you’d like to install them and set the 12V direct power
wires where you will install them.
2. Next, choose a mounting location for the control box
while making sure you leave enough wire to reach both
the LED strip lights and the 12V power input. If you need
more wire length, use LED INNOVATION item number
23914, 4’ Extension Cord 2PK, sold separately.
For additional 12” exterior light strips, use
LED INNOVATION item number 23917. Clean the
control box installation surface thoroughly with alcohol
and allow to dry before installation. Install your control
box using the included two-sided tape and optional
screws. Drill a pilot hole using a 1/16” bit before
inserting the screws.
8. Connect the red (+) positive power source that is
switched (like a running light) so the light strips will
light only when the vehicle ignition is turned on.
9. Or you can connect the red (+) positive wire to a
circuit with constant power and add your own switch
to turn it on and off. The LED INNOVATION APP also
includes a master ON/OFF switch.
10. Connect the black (-) negative wire to any clean
metal ground.
11. Tuck and secure all wires with cable ties.
12. Start your vehicle. Open your LED INNOV APP and
choose to connect to the “EXT HUB” 1 channel system.
Mobile phone must be within Bluetooth range
(Approximately 30 feet of the control box).
13. You have now successfully installed your new lighting
system and are ready to customize it using the
LED INNOV APP. Please see the “Info” tab on your
LED INNOV APP for important tips.
WARNING
• Never use the LED Innovation App while driving & obey all traffic laws.
• This product is intended solely for the purpose of decorative or
off-road use. Check laws and/or regulations in your state, county
and/or municipality regarding installation and use of this product.
This product is not DOT Approved.
• Do not install this product or run its wires near any moving parts.
Keep all wires and lighting units away from excessively hot areas.
• 12 Volt use only. Product designed to draw up to 2.8 Amps.