DRAPERY TRACK Installation Manual and User Guide 1
Diagram TABLE OF CONTENTS List of Parts Wall Mount Drapery Track Installation and Connecting the Motors Ceiling Mount Drapery Track Installation and Connecting the Motors Install the Facia (Optional) Start Up Optional Programming Steps for the Track Drapery Change Positions on the Track Drapery (Single) Change Positions on the Track Drapery (Dual) Enable or Disable Smart Assist Pair the Remote Control Grouping Multiple Drapery Together Switch the Open and Close Positions Change the Frequency Swap the Open
Wall Mount DRapery Track Installation and connecting the motors 1. Install the Brackets The number of brackets needed will depend on the desired length of the track. Screw a bracket into the wall every 16 inches, or closer if needed. Be conscious of wall substrait and drapery weight. If necessary, to use toggles or anchors to add strength. Be sure to install the first bracket close to where the motor will hang. Fig. X 2. Secure the Camlocks On the under side of each bracket place a camlock.
Ceiling Mount DRapery Track Installation and connecting the motors 1. Install the Camlock Supports The number of camlock supports needed will depend on the desired length of the track. Mount a bracket every 16 inches along the ceiling. 2. Install the Track (Optional) Install the Facia 1. Clip on the Facia Is the process different for wall and ceiling mount installtaions? Get steps from Joseph. Fig. X Fig. X Starting in the middle, secure the track onto each of the brackets. Fig. X 3.
Start up Optional Programming steps for the Drapery Track 1. Connect Power On battery powered units, unscrew the the TAU from the fastener and insert (6) or (8) D Alkaline batteries, negative end first. Screw the TAU back onto the fastener. On rechargeable battery powered units, screw the TAU onto the fastener. On low voltage units, power up by plugging the unit into the desired outlet.
Change the Close Position 1. Enter Learn Mode Pull down and release the TAU so the drapery moves towards the direction you would like to set as the “close” position. After the drapery reaches the position, it will stop moving. Pull down and hold the TAU for five seconds, or until the drapery jogs. Release the TAU. Fig. X Fig. X Note: If you have a remote control paired to the device, you can use it to move the curtain into the desired full close position.
2. Set the Close Position Change the Close Position for the window side curtain By hand, pull the curtain until it reaches the desired full close position. Fig. X 3. Exit Mode Pull down on the TAU once to exit learn mode. The drapery will jog to confirm it has learned this position. Fig. X Change the open Position for the window side curtain (Motor 2) 1. Enter Learn Mode Lift up and release the TAU so the drapery moves towards the direction you would like to set as the “open” position.
Enable or disable smart assist Smart Assist allows users to pull the curtain manually and have the movement complete automatically. All drapery tracks come with Smart Assist enabled. 1. Move the Drapery Manually Begin with the curtain in the full open or full closed position. Manually move the drapery more than a foot towards the opposite direction. If Smart Assist is enabled, the drapery will begin to complete the movement automatically. Fig. X 2.
Grouping Multiple Drapery Together 1. Enter Pairing Mode On each drapery you would like to group, pull down on the TAU twice. After the first pull, the drapery should move. The second pull should stop it. 2. Confirm Grouping On a central unit you would like to designate as the ‘Master’, press and hold the light sensor button on the control housing until the LED flashes. Each drapery will jog to confirm it has been successfully grouped. Fig. X Fig. X Switch the “Open” and “close” Positions 1.
The LEDs will change to reflect the current frequency (Fig. X). Stop when you determine the frequency matches the frequency from the bridge. Frequency Number LED Pattern 1 434.625 2 434.825 3 435.025 4 435.225 5 435.425 6 435.625 7 435.825 8 436.025 Fig. X 4. Exit Frequency Change Mode When you reach the desired frequency, exit the mode by pressing and releasing one of the two lower remote buttons.
Master Reset the Drapery 2. Swap Directions for Motor 2 To swap the open and close directions for motor 2, press and release the bottom left button. 3. Confirm On the drapery you wish to swap the open and close direction of, pull down and release the TAU once. The drapery will jog to confirm it has switched open and close directions. Fig. X Fig. X In some instances it may become necessary to master reset your drapery.
Connect & Integrate the drapery Track 1. Download the App Pair or Unpair A Remote Control Download the Current Products Corp. app from the Google Play Store or the App Store. Follow the prompts to set up your account. 1. Initiate Learn Mode Pull down and release the TAU twice to enter learn mode. After the first tug, the drapery should start moving. The second tug should stop it.
Integrate with Amazon Echo - 434 FM 1. Set up your Echo If your Alexa device is not yet set up, do so now by following the instructions that came with your device. Also be sure the bridge has been setup. For instructions on how to set up your bridge and app, go to page ____. 1. Set up your Echo Fig. X 2. Download the Skill Fig. X 3. Sign In Use the login credentials you created when you first set up your bridge and app. You are now able to control your devices via Amazon Alexa. Using Alexa Fig.
Integrate with Amazon Echo Plus- ZigBee Integrate with Google Home Integrate with Control4 1. Set up your Echo If your Alexa device is not yet set up, do so now by following the instructions that came with your device. 2. Add a Device From the menu in the Alexa app, go to “Smart Home” and hit “Add a Device”. Alternately, you can say “Alexa, search for devices”. After Alexa has completed her search, pull down and release the TAU twice on each drapery you want to pair to Alexa.
Using the DRapery Track Using the Remote Control- Single Drapery Using the TAU for Operation The TAU, or Tug Activation Unit, can be pulled down or pushed up, depending on the desired movement. On a single drapery, pulling the TAU down activates the curtain. Pulling down once makes the curtain move towards the next position, depending on if the curtain is open or closed. Pushing the TAU up will stop it. Pulling down a second time after stopping will allow the curtain to move in the opposite direction.
Using the Remote Control- Dual Drapery Full open primary Full Closed Primary Full Open secondary Full Closed secondary Using the Light & Temperature Sensors on the control housing Light Sensor Control Light Sensor LED Indicator Temperature Sensor Control Temperature Sensor LED Indicator LED Indicators Sensors Power Sensors Power LED Indicator Full Open Primary- A press and release moves the drapery plugged into the motor 1 slot to the full open position.
SAFETY INFORMATION Sensor Modes The integrated light and temperature sensors have three possible modes: Off, Fully Automatic, and Semi-Automatic. Off- The device will not make any movement triggered by this sensor. Fully Automatic- The device will open and close the curtains based on the sensor readings. Semi-Automatic- The device will close the curtains based on sensor readings, but will not open them. These modes are indicated using the LEDs on the right of the control box.
RF WARNING STATEMENT The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction. IC STATEMENT This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.