Installation Guide

展开尺寸：420*290mm
Wireless Integral Zigbee and BLE Module
WIZ10 Sensor
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save these instructions for future use.
Risk of electrical shock. Disconnect power before service
installation, or maintenance of the product.
Installation Guide
CTRL027
IMPORTANT
FCC / IC COMPLIANCE STATEMENTS
To ensure the product warranty is valid, please ensure
all installation instructions and environmental conditions
for storage and operation are complied with.
Only GE trained contractors can install the product.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
To satisfy FCC/ISED RF exposure requirements a separation
distance of 20 cm or more must be maintained between the
antenna of this device and persons during operation. Operation
at closer than 20cm is not permitted.
Pour être conforme aux limites d’exposition aux ondes RF des
normes FCC/ISED, une distance de séparation d’au moins 20 cm
doit être maintenue entre l’antenne de cet appareil et toute
personne pendant son opération. Mettre en opération cet appareil
a une distance plus rapprochée que 20 cm n’est pas permis.
Risk of injury. Wear safety glasses and gloves during
installation and servicing.
Risk of fire. Follow all relevant IEC or UL instructions and
local building codes.
WARNING
WARNING
CAUTION
Prepare Electrical Wiring
Electrical Requirements
In case of Digital bus miswiring, mains can be present
on the device. Make sure all electricity is switched off
before inspection.
Grounding Instructions
The grounding and bonding of the overall system
shall be done in accordance with National Electric
Code (NEC) Article 600 and local codes.
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference.
• This device must accept any interference, including interference
that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
• L’appareil ne doit pas produire de brouillage;
• L’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
Key Functions
Notes
Product Availability Product Certifications
Product Overview
Technical Data
E486320
FCC ID: 2AS3F-WIZ10
IC: 25008-WIZ10
95047448 Wireless Integral Zigbee and BLE Module WIZ10
SKU DESCRIPTION ARTICLE NO.
Max. 22.5V, Class 2, capable of no greater than 15VA power
See Dimensional Diagram
12.8g
Max 8mA(without digital communication)@Max 22.5V Class 2
BLE iBeacon function
0℃ to 50℃(Indoor)
Network joined
Cable connection to driver or interface module
Installs within a 22mm (0.87”) hole with provided nut
10 feet
5 years
Operating Control
The Wireless Integral Zigbee and BLE Module (WIZ10) is a small-size sensor for use with luminaires, through integration or
adjacent attachment. Using the WIZ10 sensor with each luminaire can connect to the Daintree Enterprise Lighting Control
System while enabling dimming and on/off commands to be delivered to the luminaire . The control of the luminaire is carried
out through a digital bus between the sensor and the luminaire’s driver/controller; the digital bus also provides the necessary
power for the sensor. The wireless communication with the Daintree Enterprise WAC60 utilizes ZigBee which results in a secure
and reliable connection and helps minimize the installation costs and complexity.
All trademarks are the property of their respective owners. Information provided is subject to
change without notice. All values are design or typical values when measured under laboratory
conditions. Current, powered by GE is a business of the General Electric Company.
© 2018 GE.
www.currentbyge.com
Company name: Current Lighting Solutions, LLC
Address: 1975 Noble Road, East Cleveland, OH 44112
CTRL027 (Rev 06/01/18)
Cable Connection to Driver
Dimensions Sensor Pattern
WIZ10
2
1DA-
DA+
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
Fault reporting not
available, dimming curve not selectable
Purpose of the Control