Declaration of Conformity

STOP
WARNING/AVERTISSEMENT
Read these instructions completely and carefully.
Turn power off before inspection, installation or removal.
Properly ground electrical enclosure.
Follow all NEC and local codes.
Use only UL approved wire for input/output connections.
Minimum size 14 AWG for continuous runs.
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Coupez l'alimentation avant d'inspecter, installer ou déplacer le luminaire.
Assurez-vous de correctement mettre à la terre le boitier d'alimentation électrique.
Respectez tous les codes NEC et codes locaux.
N'utilisez que des fils approuvés par UL pour les entrées / sorties de
connexion. Taille minimum 14 AWG.
BEFORE YOU BEGIN
RISK OF ELECTRIC SHOCK
Save These Instructions
RISK OF ELECTRIC SHOCK
RISQUES DE DÉCHARGES ÉLECTRIQUES
RISQUES D'INCENDIE
Lighting Solutions
ZigBee
WGZ100
24-14
Left : (N)Input、(L)Input、(L)Relay Output
Right : 0-10V GND、0-10V OUT、Dali+、Dali-
or LED Driver
for P2 terminal
Translate Wireless ZigBee messaging to control electronic ballast or LED Driver:
10 years
32mA
Type 1.B action Pollution degree 2 Rated Impulse voltage 4000V
NN
(N) Input White
(L) Input Black
(L) Relay Output Red
(-) 0-10V GND Grey
(+) 0-10V OUT Purple
0-10V LED Driver
ZigBee to 0-10V Interface
Driver Line (L)
Driver Neutral (N)
Wire Nut
(N) (L)
Driver 0-10V Dimming Wires
Driver LED Output Wires
(to LED Array)
(+)
(-)
Fixture Mains
(via code-compliant conduit)
Fixture Driver Housing
(or code-compliant wiring box)
(+)
(-)
The interface and wiring is intended to be installed and
completely enclosed within the same NEC Class 1 driver
housing as the 0-10V driver using metal mounting screws
(not provided).
(Relay Output)
(L)
(N)
(Relay Output)
(N) (L)
Caution: The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator
and any part of your body.
This device complies with Industry Canada’s license exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm
between the radiator and any part of your body.
Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au
moins 20 cm doit être maintenue entre l'antenne de cet appareil ettoutes les personnes.
FCC sDoC statement
FCC Supplier ’s Declaration of Conformity
Brand name: GE Lighting / model number: WGZ100
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may
cause undesired operation.
Suppliers Name: GE Lighting Solutions
Suppliers Address (USA): Nela Park, Cleveland, Ohio, 44112
Suppliers phone number and / or internet contact information: 1-888-MYGELED
&$1,&(6
DWLRQ