Oakmont Pellet Grill and Smoker ASSEMBLY INSTRUCTIONS Model SMK2036AS
ASSEMBLY INSTRUCTIONS: READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
4 1 2 3 9 5 7 6 8 10 13 11 15 16 12 17 14 19 21 18 20 22 24 26 23 25 30 27 29 31 32 28 33 34 36 35 2
Step 1 • Loosen 4 screws. • Attach front legs 12 and 13 front panel 30 using keyholes. • Tighten 4 screws. • Remove 8 screws. 30 Remove 12 13 Remove NOTE: Before tightening keyhole screws, make sure panels are aligned. Step 2 • Attach side cart braces 11 to front legs 12 and 13 using 4 screws removed from Step 1.
Step 3 • Attach cart base 26 to front legs 12 and 13 using 4 screws removed from Step 1. 12 13 26 Step 4 5 14 • Remove 12 screws. • Attach rear cart brace 5 to rear legs( 14 and 15 ) using 4 screws just removed.
Step 5 • Attach side cart braces 11 to rear legs ( 14 and 15 ) using 4 screws removed from Step 4. 11 14 11 15 Step 6 • Attach cart base 26 to rear legs ( 14 and 15 ) using 4 screws removed from Step 4. • Tighten all screws.
Step 7 • Lock casters 21 . • Attach casters 21 to legs. 21 CASTERS unlocked locked Step 8 17 • 16 Attach temperature gauge 17 and bezel 16 to hood using pre-attached washer and wing nut.
Step 9 • Loosen 2 rear screws and remove 2 front screws on both sides of grill body 9 . • Set grill body 9 on cart. Make sure rear screws drop into cart brackets. • Install front screws through front brackets. • Tighten 4 screws. Loosen 9 Remove Step 10 • Remove 4 screws from grease cup bracket 31 . • Attach grease cup bracket 31 to bottom of firebox using 4 screws just removed.
Step 11 • Remove 4 screws from ash cup brackets 32 . • Attach ash cup brackets 32 to bottom of firebox using 4 screws just removed. 32 Step 12 • 35 Install ash cup 35 and grease cup 34 .
Step 13 • Remove 2 screws. • Attach grease channel 8. • Tighten 2 screws. 8 Step 14 • Attach control knob 36 to the controller located on the pellet hopper assembly 28 .
Step 15 • Install pellet hopper assembly 28 into grill body. • Attach pellet hopper assembly 28 to grill body using 4 screws. (These screws are in the bag with the owner’s manual.) • Tighten 4 screws. 28 Note: When assembling the pellet hopper to the grill, the light wires should be fed through the back side of the pellet hopper to ensure there is enough wire to connect during Step 29b. Light Wires Step 16 • Remove 2 screws from ash clean-out plate 23 and set aside for later use.
Step 17 • Insert ash clean-out handle 24 through back of grill body. • Attach ash clean-out handle 24 to ash cleanout panel 23 using 2 screws removed from Step 16. 24 Step 18 • Remove 3 screws. • Attach heat plate bracket 19 using 3 screws just removed.
Step 19 • Remove 1 screw from heat baffle 33 . • Insert the heat baffle pin into auger box and tighten screw to hold in place. 33 Step 20 Thermocouple Wire 10 • Remove 2 screws. • Attach thermocouple assembly 10 using 2 screws just removed. Note: Make sure to feed the thermocouple wire on the back side of the auger box to ensure there is enough wire to connect during Step 29b.
Step 21 • Attach side handle 25 using 2 pre-attached screws from side handle. 25 Step 22 • Remove 8 screws. • Attach hopper lid 20 to pellet hopper body using 8 screws just removed.
Step 23 • Remove 2 screws. • Attach cord wrap 29 using 2 screws just removed. 29 Step 24 • Remove 5 screws. • Attach chimney 2 using 5 screws just removed.
Step 25 • Install hood handle 3 using screws and bezels pre-installed on handle. 3 Step 26 • • Remove 4 shoulder bolts from left and right table brackets 7 and 6 . Attach left and right table brackets 7 and 6 to side table 1 and front table 27 using shoulder bolts just removed.
Step 27 • Remove 4 screws from grill body. • Attach side table 1 to grill body using 4 screws just removed. 1 Step 28 • Remove 4 screws from grill body. • Attach front table 27 using 4 screws just removed.
Step 29a • Remove 1 screw from the bottom of pellet hopper panel. Step 29b • Connect the thermocouple connector and the two 10 watt light connectors. These wires can only be connected one way. Thermocouple Connector Note: All connectors must be connected in order for the grill to function properly. 10 watt Light Connectors Step 29c • 17 Close pellet hopper bottom panel and secure with screw.
Step 30 • Place heat plate 22 inside cooking chamber on brackets. Note: The heat plate should set in the grease channel and the heat plate bracket. Once installed the heat plate will slope down to the left to ensure grease flows into the grease cup. 22 Step 31 • Place 4 cooking grates 18 inside cooking chamber.
Step 33 • Place the warming rack 4 on supports inside cooking chamber.
Model SMK2036AS Assembled OM2036AS/ASO 0921 ©2021 The Boltz Group LLC. Carrollton, Texas 75006 U.S.A.