Operator’s Manual Triple Rear Bagger — 19A30018100 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No.
1 To The Owner Thank You Thank you for purchasing a Cub Cadet Bagging attachment. It was carefully engineered to provide excellent performance when properly operated and maintained. IMPORTANT: If installing this bagging kit on a ZF-L (lap bar) unit, bumper adaptor kit 19A70046100 is required and must be installed prior to attempting to install this bagger. See the retailer in which you purchased this bagger to purchase this adapter kit. Please read this entire manual prior to operating the equipment.
2 Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! DANGER! This attachment was built to be used according to the safe operation practices in this manual.
(OK) Figure 1 line Slope Gauge 10° Slope 1 0 ° d a s hed USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.) 3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ). 4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2). 5.
3 Contents of Carton Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Figure 3-1. Two hardware packs are included in this kit and are detailed on the following page. • Upper Chute Tube • Grass Catcher Cover • Discharge Chute Elbow • Hitch Bracket Kit (3 Pcs.
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with two loose hardware packs enclosed. Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis.
4 Assembly & Installation Note: References to left, right, front and rear of the tractor are from the operator’s position, unless otherwise stated. • Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. Tools Required • 1/2” wrench or socket Assemble Mounting Brackets Use this mounting hole To assemble the bagger mounting assembly, locate the mounting assembly pack and follow these steps: 1.
Note: The clevis pin can be fed down through the hitch plate and secured underneath with the hairpin clip, or it may be easier to feed the clevis pin up through the hitch plate hole and secure with the hairpin clip on the topside. The latter method may be preferred since it can be easier to insert the hairpin clip. Either way will work, the decision should be based on operator preference. The clevis pin has two holes. It is recommended to use the hole closest to the head of the pin for a tighter connection.
Assembling Remaining Bagger Components 4. Now that the mounting brackets are assembled and are in place on the tractor, follow these steps to assemble the remaining bagger components. 1. Snap the plastic upper chute support in place by first clipping the side portion onto the bagger support rail (1) with the edge of the snap feature aligned with the red line, as seen in the inset of Figure 4-7. 2 Clip in the other side by flexing the screen and pushing it down into the provided cutout hole.
8. Install the bag assemblies, with the tight mesh panel facing the tractor, onto the bag support brackets by inserting the front edge in first, as shown in 1 of Figure 4-14, and setting the back edge down(2) until it fits into the assembly. 1 2 Figure 4-11 Figure 4-14 Assembling and Configuring the Discharge Chute Before installing the discharge chute onto your tractor, a component must first be assembled onto the upper chute tube.
Installing the Discharge Chute 6. When installing the discharge chute, two different installation instructions exist. For the 54” Fabricated deck units, the discharge chute elbow mounts directly onto the cutting deck. For the 50” and 54” stamped decks, an adapter must first be installed. Be sure to follow the instructions that pertain to the unit you are installing this bagger on. Secure the discharge chute elbow to the cutting deck using a (720-04122) wing knob included in Hardware Pack 68900341.
4. Insert the end of the discharge chute elbow (1) into the hole provided in the deck wheel mount as shown in the inset of Figure 4-19. IMPORTANT: Be certain that the bottom of the discharge chute is located inside of the lip of the deck opening, as shown in Figure 4-21. 2 1 Do Not Use This Hole! Figure 4-19 5. 6. Pivot the discharge chute rearward until the hole in the discharge chute elbow aligns with the pin on the deck adapter.
5 Operation Bagger Usage 3. NOTE: When all of the grass bags are full, place the tractor on a firm, level surface, disengage the PTO, turn the tractor engine off and set the parking brake. 1. Pivot the seat forward and up. 2. Lift up grass bag cover by pushing in on the rear, right-side tab with your right hand, as seen in 1 of Figure 5-1, and lifting the cover with your left hand in the center rear of the bagger cover, 2. Do not remove the chute tube assembly from the tractor.
This page intentionally left blank.
6 19A30018OEM Parts List 2 5 9 4 14 12 19 18 10 13 6 17 11 3 6 8 6 7 21 6 7 20 16 7 22 15 1 16
Ref. Part Number Description 1. 931-04291 Upper Chute Assembly 2. 631-04298P Triple Bagger Cover Assembly 3. 731-06497 Upper Chute Support 4. 731-06504 Bagger Cover Screen 5. 721-04388 Adhesive Foam Strip 6. 710-0276 Carriage Screw, 5/16-18 x 1.00” 7. 720-04122 Wing Knob, 5/16-18 8. 711-0309A Clevis Pin, .62” Dia. 9. 964-04096A Grass-bag Assembly 10. 683-04498A-0637 Triple Bag Support Assembly 11. 683-04519B-0637 Vertical Support Bracket 12.
Notes 18 7
Section 7 — Notes 19
CUB CADET LLC MANUFACTURER’S LIMITED WARRANTY FOR SEPARATELY SOLD ATTACHMENTS AND ACCESSORIES IMPORTANT: To obtain warranty coverage owner may be required to present an original proof of purchase and applicable maintenance records to the servicing dealer. Please see the operator’s manual for information on required maintenance and service intervals.