EXHIBIT 8 USER’S MANUAL
CSI-Wireless Wireless-Link LoCate-001 Users Manual Document: LoCate-001 Users Manual Date: 01/06/06 Issue: Rev. 1.
CSI-Wireless LoCate-001 Users Manual TABLE OF CONTENTS DEFINITIONS.................................................................................................................... 3 1 INTRODUCTION ........................................................................................................ 4 1.1 OPERATIONAL OVERVIEW ........................................................................................4 1.2 SYSTEM FEATURES ...................................................................
CSI-Wireless Cellular Section DAC DGPS DSP EEPROM ESD ESN FCP GPS ID I/O LJU LNCC MIN PPM RAM RF RSSI RTC RX SAT SID ST TX UTC VSWR LoCate-001 Users Manual Cellular Data Modem for AMPS Digital to Analog Converter Differential Global Positioning System Digital Signal Processor Electronic Erasable Programmable Read Only Memory Electrostatic Discharge Electronic Serial Number Function Control Processor Global Positioning System Identification (Numeric or alpha value) Inputs and/or outputs LoJack Unit LoJack
CSI-Wireless LoCate-001 Users Manual 1 Introduction 1.1 Operational Overview The LoCate-001 vehicle unit provides a specific set of features for vehicle security and vehicle tracking through the integration of Cellular Control Channel data communications, Global Positioning System (GPS) technology, and an intelligent power management.
CSI-Wireless LoCate-001 Users Manual LoJack Fleet Management Network Internet Browser-Based Real Time Dispatching LOJACK NETWORK/ISP Browser-Based Real Time Vehicle Tracking Worker’s PCS Phone for voice and data dispatching Cellular/PCS Carrier Fleet OnePhone TM OnePhone Provides Vehicle Security & AVL Aeris Cellemetry Figure 2 - Typical LoCate-001 Commercial Application Both commercial and consumer products can offer a basic set of security features for a one time cost at the point of hardware s
CSI-Wireless 1.2 LoCate-001 Users Manual System Features The LoCate-001 unit incorporates the following major features: 1.3 • Integrated Microburst radio, GPS receiver and power management modules. • Real Time Clock for scheduling and power management. • Low power mode. • Event schedules & triggers • Protected automotive power supply. System Description The LoCate-001 Product consists of the following major components: • • • • • • • Twelve Channel GPS Receiver.
CSI-Wireless 1.4 LoCate-001 Users Manual Operating Modes The LoCate-001 unit offers two major operating modes. 1.4.1 Armed Mode When either of the LoCate-001 digital inputs becomes active, the LoCate-001 enters the Armed mode within 1 second. The LoCate-001 will enter the Armed Mode based on activity on the analog input only during the wakeup period.
CSI-Wireless LoCate-001 Users Manual During the Armed mode the GPS receiver is immediately powered off after getting a valid fix and determining that the vehicle has not moved. However, the cellular transceiver will remain on for the duration of the ‘wake-up/status check’ cycle to listen for messages from the LNCC. 2.1.2 Geo-fences At the time of the installation the LoCate-001 may be factory programmed with 3 Geo-fences, and defaulted to the first 0-25 mile fence as follows: 1.
CSI-Wireless 2.3 LoCate-001 Users Manual External I/O The seven I/O ports of the LoCate-001 device are configured as follows: Port # 1 Designation Type Function Output Relay Driver Doors Unlock Relay 2 Output 3 Input 4 Input 5 6 7 Output Output Input Signal Chracterics Pulse active low, 1 second maximum Relay Driver Starter Enable/disable Level, stays high Relay or low as determined by MIN3 / MIN4 Digital Crash Sensor, Low Impact Active low, minimum 1 second.
CSI-Wireless 2.6 LoCate-001 Users Manual Status The following status criteria will be displayed in the Asset Vision Link test software, connected to the LoCate-001 via the RS232 serial port. • • • • • • • • 2.7 GPS fix attained (Yes/No) Antenna Status (Connected/disconnected) Cellular RSSI Asset voltage Asset ID Internal phone number (MIN) System Identification (SID) ESN Power Consumption Profile The LoCate-001 unit has three major operating modes: Revision 1.
CSI-Wireless 3 3.1 LoCate-001 Users Manual Performance Specifications Cellular Transceiver Parameter Frequency Range (Tx) Frequency Range (Rx) Channel Spacing Deviation Number of Channels Antenna Impedance Receiver Sensitivity Transmitter Power Output Peak Deviation Frequency Stability Carrier Switching Time Channel Switching Time Specification 824.010 – 848.970 869.010 – 893.970 30 ± 12 832 50 -116 0.6 +/- 8 +/- 2.5 2 40 Units MHz MHz KHz KHz Max.
CSI-Wireless 3.3 LoCate-001 Users Manual LoCate-001 Antenna Specifications The LoCate-001 unit requires two separate antennas, Cellular and GPS. 3.3.1 Warning on use of cellular antennas The cellular antenna supplied with this unit must be used for installation and operation. Substitution of other antennas must be approved by the manufacturer for compliance to radiation safety limits.
CSI-Wireless 3.4 3.4.1 LoCate-001 Users Manual Environmental Requirements Temperature and Humidity Parameter Operating Temperature Range Storage Temperature Range Operating Humidity @ -30°C to +60 °C, %RH non condensing Minimum -30 °C -30 °C 0% Maximum +60 °C +60 °C 95 % Table 10 – Temperature & Humidity Specification 3.4.2 3.5 3.5.1 Vibration The LoCate-001 is designed to be mounted in a non-frame area of a car or truck.
CSI-Wireless LoCate-001 Users Manual Input High Voltage Input Low Voltage RELAY DRIVER: Output Impedance Input High Voltage for less than 1 mA draw Reverse Voltage at 1 mA draw 6.5V -0.3V 7.5V -0.6V 0 ohm 0V 3 ohm 32V 0V -2V Table 13 – Analogue & Digital Ports Specifications Revision 1.
CSI-Wireless 3.5.3 LoCate-001 Users Manual External Connector Pin Assignments The external I/O connector pin assignments are as follows: Connector: Molex 53259-1310 or equivalent Mating connector, for customer-supplied cable harness: Molex 51067-1300 or equivalent Pin Description 1 2 3 Relay Driver 1 Relay Driver 2 Digital Output 1 4 5 6 7 8 9 10 11 12 13 Notes Connects relay coil to ground, other side of relay coil goes to supply positive.
CSI-Wireless 4 4.1 LoCate-001 Users Manual Mechanical and Physical Housing The LoCate-001 consists of a PCB contained inside a housing. The approximate size of the LoCate-001 is 156 mm (L) x 100 mm (W) x 25.4 mm (H). 1. The housing is aluminium cast. 2. Three mounting tabs will allow for use of a size 10 pan head screw. 3. The outside color of the housing is black. LoCate-001 housing 4.2 Connection & Identification Requirements The LoCate-001 unit shall be supplied with the following; 1.
