User's Manual

ManualsBrandsCSI Wireless ManualsElectronicsAssetLink 200

NJIAL200

EXHIBIT 7

“Users Manual”

This exhibit is submitted to comply in part with

FCC 47CFR section 2.1033 part b item 3:

“ A copy of the installation and operating instructions to be

furnished the user. A draft copy of the instructions may be

submitted if the actual document is not available. The actual

document shall be furnished when it becomes available.”

This exhibit is submitted to comply with

FCC 47CFR section 2.1033 part c item 3:

“A copy of the installation and operating instruction to be

furnished the user. A draft copy of the instructions may be

submitted if the actual document is not available. The actual

document shall be furnished to the FCC when it becomes

available.”

Summary of content (13 pages)

PAGE 1
NJIAL200 EXHIBIT 7 “Users Manual” This exhibit is submitted to comply in part with FCC 47CFR section 2.1033 part b item 3: “ A copy of the installation and operating instructions to be furnished the user. A draft copy of the instructions may be submitted if the actual document is not available. The actual document shall be furnished when it becomes available.” This exhibit is submitted to comply with FCC 47CFR section 2.
PAGE 2
Submission examination in detail on FCC 47CFR section 2.1033 part b item 3: Whereas the “Installation and Operating Instructions” is shown below, and the reference in section 2.1033 for the same document is the “installation and operation instructions”, and the Form 731 equivalent reference is the “User Manual”, the “Installation and Operating Instructions” document is used as a submission for this requirement and is evidenced. Submission examination on FCC 47CFR section 2.
PAGE 3
CSI-Wireless AssetLink 200 Installation and Operating Instructions CSI-Wireless Wireless-Link AssetLink 200 Installation and Operating Instructions Revision 1.
PAGE 4
CSI-Wireless AssetLink 200 Installation and Operating Instructions Document: AssetLink 200 Installation and Operating Instructions Date: January 2, 2002 Issue: Rev. 1.0 Author: Russ Braathen copyright 2001 CSI-Wireless Inc. TABLE OF CONTENTS DEFINITIONS ............................................................................................................................... 3 1 INTRODUCTION..............................................................................................................
PAGE 5
CSI-Wireless AssetLink 200 Installation and Operating Instructions Acronyms and Abbreviations bps AMPS Cellular Section DAC DGPS DSP EEPROM ESD ESN FCP GPS ID I/O MIN NCC PPM RAM RF RSSI RTC RX SAT SID ST TX UTC VSWR Bits per Second American Mobile Phone System Cellular Data Modem for AMPS Digital to Analog Converter Differential Global Positioning System Digital Signal Processor Electronic Erasable Programmable Read Only Memory Electrostatic Discharge Electronic Serial Number Function Control Processor
PAGE 6
CSI-Wireless 1 AssetLink 200 Installation and Operating Instructions Introduction 1.1 Operational Overview The AssetLink 200 vehicle unit provides a specific set of features for vehicle security and vehicle tracking through the integration of Cellular Control Channel data communications, Cellular Voice Channel data communications, Global Positioning System (GPS) technology, and an intelligent power management.
PAGE 7
CSI-Wireless AssetLink 200 Installation and Operating Instructions The GPS receiver can be configured during the Armed Mode to specify the “maximum time to fix” interval allowed for the GPS receiver to get a fix before powering off the GPS. This mode is necessary in situations where the GPS antenna is completely hidden from the sky and cannot get an updated position fix during its Armed Mode ‘wake-up/status check’ cycle.
PAGE 8
CSI-Wireless 2.
PAGE 9
CSI-Wireless • • 2.6 3 3.1 AssetLink 200 Installation and Operating Instructions System Identification (SID) ESN Power Consumption Profile The AssetLink 200 unit has three major operating modes: Power Off This is the lowest consumption mode to maintain the RTC, relay outputd digital outputs and monitor external digital inputs. The current draw from the supply lines in this mode is less than 30 microamperes at 12 volts.
PAGE 10
CSI-Wireless AssetLink 200 Installation and Operating Instructions Warm Start Cold Start Minimum Signal Tracked Maximum Velocity Consumption Voltage Protocols Position Accuracy < 38 seconds < 45 seconds -175 dBW < 1,000 knots 150 mA 3.15 to 5.5 VDC NMEA v2.2, SiRF Binary 100 meter 2d RMS SA On 10 meter 2d RMS Table 7 – GPS Receiver Specifications 3.3 AssetLink 200 Antenna Specifications The AssetLink 200 unit requires two separate antennas, Cellular and GPS. 3.3.
PAGE 11
CSI-Wireless 3.4 3.4.1 AssetLink 200 Installation and Operating Instructions Environmental Requirements Temperature and Humidity Minimum -30 °C -50 °C 0% Parameter Operating Temperature Range Storage Temperature Range Operating Humidity @ -30°C to +60 °C, %RH non condensing Maximum +60 °C +80 °C 90 % Table 10 – Temperature & Humidity Specification 3.4.2 3.5 3.5.1 Vibration The AssetLink 200 is designed for mounting in the passenger compartment, which is a non-frame area of a car or truck.
PAGE 12
CSI-Wireless AssetLink 200 Installation and Operating Instructions RELAY DRIVER: Output Impedance Input High Voltage for less than 1 mA draw Reverse Voltage at 1 mA draw 0 ohm 0V 3 ohm 32V 0V -2V Table 13 – Analogue & Digital Lines Specifications 3.5.
PAGE 13
CSI-Wireless 4 4.1 AssetLink 200 Installation and Operating Instructions Mechanical and Physical Housing The AssetLink 200 consists of a PCB contained inside a housing. The approximate size of the AssetLink 200 is 156 mm (L) x 100 mm (W) x 25.4 mm (H). 1. The housing is cast aluminium, 2. Three mounting tabs will allow for use of a size 6 pan head screw, 3. The outside color of the housing is black. AssetLink 200 mounting dimensions Revision 1.