BEDIENUNGSANLEITUNG USER’S MANUAL MODE D’EMPLOI MANUALE D’USO MANUAL DE USO GTO 21 20 2-KANAL VERSTÄRKER 2 CHANNEL AMPLIFIER AMPLIFICATEUR 2 CANAUX AMPLIFICATORE 2 CANALI AMPLIFICADOR DE 2 CANALES
INHALTSVERZEICHNIS TABLE OF CONTENT TABLE DES MATIÈRES SOMMARIO INDICE DEU BEDIENUNGSANLEITUNG 3 ENG USER’S MANUAL 8 FRA MODE D’EMPLOI 13 ITA MANUALE D´USO 18 ESP MANUAL DE USO 23 ABBILDUNGEN / FIGURES / FIGURES / FIGURE / FIGURES 28
DEU Bitte lesen Sie die Bedienungsanleitung vollständig durch, bevor Sie mit der Installation beginnen und den Verstärker in Betrieb nehmen. TECHNISCHE DATEN GTO2120 Ausgangsleistung RMS 2 x 70 W an 4 Ohm 2 x 120 W an 2 Ohm Ausgangsleistung Max.
DEU HINWEISE VOR DER INSTALLATION - Dieser Verstärker ist nur zum Betrieb in einem Fahrzeug geeignet. - Dieser Verstärker ist nur zum Anschluss an ein 12-Volt-System mit negativer Masse geeignet. - Die während des Betriebs abgestrahlte Wärme erfordert einen Montageort mit ausreichender Luftzirkulation. Es ist sehr wichtig, dass die Kühlrippen des Kühlkörpers nicht an einem Blech oder an einer Oberfläche anliegen, wodurch die Luftzirkulation eingeschränkt werden könnte.
DEU HOCHPEGELEINGANG Der Hochpegeleingang (HIGH LEVEL INPUT, Abb. 1, 1) dient zur Ansteuerung des Verstärkers mittels Lautsprecherkabel, falls Ihr Steuergerät (Autoradio) nicht über Vorverstärker-Ausgänge (Cinch-Ausgänge) verfügt. Verlängern Sie dazu die entsprechenden Lautsprecherkabel, die aus Ihrem Steuergerät führen mit geeigneten hochwertigen Lautsprecherkabeln bis zum Einbauort des Verstärkers.
DEU REGELBARER HOCHPASSFILTER Sollte der Verstärker zum Betreiben von Satellitenlautsprechern (Mittel-/ Hochton-Lautsprecher) benutzt werden, stellen Sie den Schalter (X-OVER, Abb.1, 5) auf „HPF“ oder bei großen Lautsprechern ab 20 cm auf ”FULL”. Stellen Sie am Regler (LPF/HPF, Abb.1, 6) die gewünschte Trennfrequenz ein. Somit werden nur die Frequenzen oberhalb der eingestellten Trennfrequenz verstärkt. Dadurch können Verzerrungen und die Überlastung bei tieferen Frequenzen minimiert werden.
DEU 2-KANAL-BETRIEB STEREO (ABB.
ENG Please read the user's manual carefully before the installation and the first operation of the amplifier. SPECIFICATIONS GTO2120 Output Power RMS 2 x 70 W @ 4 Ohms 2 x 120 W @ 2 Ohms Output Power Max.
ENG IMPORTANT NOTES PRIOR TO INSTALLATION - This device is only suited for the operation in a vehicle. - This device is only suited for a 12 volt system with negative ground. - The radiated heat while operation requires sufficient air circulation at the place of installation. It is very important that the heatsink fins do not have contact with any metal parts or any surfaces which could impair air circulation. The amplifier may not be installed in small closed location or spaces without air circulation (e.
ENG HIGH LEVEL INPUT The HIGH LEVEL INPUT (Fig. 1, 1) is suitable to connect the amplifier inputs with speaker wires, if your headunit is not equipped with pre-amplifier RCA outputs. Extend therefore every regarding speaker cable from your headunit with appropriate speaker cables from your car audio retailer to the mounting location of the amplifier. Then connect the each matching loudspeaker cable with the cables of the included HIGH LEVEL jack like described below.
ENG VARIABLE HIGHPASS FILTER If the amplifier is to be used for satellite loudspeakers (mid-range/tweeter loudspeakers), set the switch (X-OVER, Fig. 1, 5) to "HPF" or for bigger loudspeakers (>20 cm) to ”FULL”. Set the desired crossover frequency on controller (LPF/HPF, Fig.1, 6). Thus to that only the frequencies above the chosen cross-over frequency will be amplified. This effectively minimizes distortions and overloads at lower frequencies. A good point to start is at 125 Hz.
ENG 2-CHANNEL OPERATION STEREO (FIG.
FRA Veuillez s’il vous plait lire attentivement toutes les instructions d’installation avant que vous installiez l’amplificateur et le fassiez fonctionner. CARACTERISTIQUES GTO2120 Puissance de sortie RMS 2 x 70 W @ 4 Ohm 2 x 120 W @ 2 Ohm Puissance de sortie Max.
FRA RECOMMANDATIONS AVANT L’INSTALLATION - Cette appareil est conçu uniquement pour un fonctionnement dans un véhicule. - Cet appareil convient exclusivement au branchement à un système de 12 volt à masse négative. - La chaleur provenant de l’utilisation nécessite un espace de montage avec une circulation de l’air suffisante.
FRA ENTRÉE HAUT NIVEAU L´entrée haut niveau (HIGH LEVEL INPUT, Fig. 1, 1) est appropriée pour connecter les entrées de l´amplificateur avec les fils des hauts-parleurs dans le cas où votre autoradio (source) ne serait pas équipé(e) de sorties RCA. Grâce aux câbles appropriés fournit par votre revendeur car audio pour les hauts-parleurs, prolonger les sorties de votre autoradio jusqu`à l´emplacement où vous installerez votre amplificateur.
FRA FILTRE PASSE-HAUT RÉGABLE Dans le cas où l´amplificateur est utilisé comme amplificateur pour haut-parleurs satellites (haut-parleurs médium/aigu), positionnez le selecteur (X-OVER, Fig. 1, 5) sur "HPF"ou sur "FULL" pour les hautpaleurs >20cm. Ajustez le régulateur (HPF/LPF, Fig. 1, 6) sur la fréquence de recouvrement souhaitée. De cette manière, seules les fréquences au dessus de la fréquence de recouvrement choisie seront amplifées.
FRA FONCTIONNEMENT 2 CANAUX STEREO (FIG.
ITA Per favore leggere le istruzioni per il montaggio integralmente, prima di montare l’amplificatore e di metterlo in funzione. DATI TECNICI GTO2120 Potenza di uscita RMS 2 x 70 W @ 4 Ohm 2 x 120 W @ 2 Ohm Potenza di uscita Max.
ITA INDICAZIONI IMPORTANTI PRIMA DEL MONTAGGIO - Questo dispositivo é adatto solo per il funzionamento su autovettura - Questo apparecchio é adatto unicamente ad essere collegato con un sistema elettrico a 12 Volt con negativo a massa. - Il calore irradiato durante l’erogazione di potenza richiede un posizionamento con una sufficiente circolazione d’aria. É molto importante che le alette di raffreddamento del dissipatore non siano adiacenti ad una paratia che possa limitare la circolazione d´aria.
ITA INGRESSO ALTO LIVELLO L´ingresso alto livello (HIGH LEVEL INPUT, Fig. 1, 1) è indicato per connettere l´ingresso dell´amplificatore con I cavi degli altoparlanti nel caso la vostra sorgente non sia equipaggiata di uscite RCA. Attraverso cavi adeguati forniti dal vostro rivenditore car audio, prolungate le uscite della sorgente fino a dove volete posizionare il vostro amplificatore. A questo punto collegate I cavi corrispondenti ai cai del connettore del connettore alto livello come indicato sotto.
ITA FILTRO PASSA ALTO REGOLABILE Se l´amplificatore è impiegato per pilotare altoparlanti satelliti (Midrange / tweeter) posizionare lo selettore (X-OVER, Fig. 1, 5) in posizione "HPF" o, per altoparlanti più grandi (>20 cm) in posizione ”FULL”. Impostate la frequenza di crossover desirata impiegando il regolatore apposito (LPF/HPF, Fig.1, 6). Questo minimizza la distorsione e l´eccesso di potenza alle frequenze inferiori. Un buon punto di inizio è impostare 125Hz.
ITA COLLEGAMENTO A 2 CANALI STEREO (FIG.
ESP Lea completamente las instrucciones de montaje antes de proceder a montar el amplificador y ponerlo en funcionamiento. DATOS TÉCNICOS GTO2120 Potencia de salida RMS 2 x 70 W @ 4 Ohmios 2 x 120 W @ 2 Ohmios Potencia de salida Max.
ESP INDICACIONES IMPORTANTES PREVIAS AL MONTAJE - Este aparato solamente es apto para su funcionamiento en un vehículo. - Este equipo es adecuado sólo para la conexión a un sistema de 12 voltios con tierra negativa. - El calor irradiado hace que sea importante que instale el aparato en un lugar con suficiente circulación de aire. Es muy importante que las aletas refrigeradoras del cuerpo de refrigeración no estén situadas al lado de una chapa o superficie que pudiera limitar la circulación de aire.
ESP ENTRADA DE ALTA La entrada de alta (HIGH LEVEL INPUT, Fig. 1, 1) es adecuada para conectar la entrada de amplificador con cable de altavoz si su unidad radio-CD no esta dotada de salidas de previo. Amplíe los cables de salida de la unidad radio-CD hasta la ubicaciòn del amplificador con cable de altavoz adecuado que puede proporcionarle su instalador autorizado. Conecte cada cable con los conectores de salida de alta correspondientes, según se indica mas abajo.
ESP FILTRO DE PASO ALTO REGULABLE Si el amplificador se usará para altavoces stélite (medios/tweeter etc) colocar el selector en posición "HPF" (X-OVER, Fig.1, 5). Para altavoces más grandes (medios-graves, mas de 10") colocar el selector en Full. Seleccionar el corte de frecuencia deseado en el regulador (LPF/HPF, Fig.1, 6). De esta forma, solo las frecuencias seleccionadas serán amplificadas. Esto minimiza la distorsión y sobre alimenta la señal en frecuencias bajas. Un buen punto de inicio es a 125 Hz.
ESP FUNCIONAMIENTO DE 2 CANALES STEREO (FIG.
1 1 3 5 2 2 4 6 2 7 1 3 6 5 4 28 + –
3 1 3 HPF FULL 2 4 5 2 - 8 Ohms 2 - 8 Ohms 29
4 1 3 LPF 2 4 4 - 8 Ohms 30
Audio Design GmbH · www.crunchaudio.de Am Breilingsweg 3 · D-76709 Kronau (Germany) Tel. +49 (0)7253 - 9465-0 · Fax +49 (0)7253 - 946510 © 2012 Audio Design GmbH, All Rights Reserved.