User's Manual

ManualsBrandsCrow Electronic Engineering ManualsElectronicsDECT ULE transceiver

DECT ULE-FLD

FLOOD DETECTOR

CR-DU-FLD EURO

CR-DU-FLD USA

ELECTRONIC ENGINEERING LTD.

INSTALLATION INSTRUCTIONS

P/N 7105193 REV. B (O.Z.)

Issue Date: July 6

, 2015

INTRODUCTION

This DECT ULE FLD detector is an advanced, fully

supervised low-current wireless detector that

includes a DECT ULE transceiver for reliable

system operation.

A dedicated cable is supplied with this device.

This DECT ULE FLD uses smart message control,

which verifies that all messages are successfully

transmitted, so that no event will be uninformed to

the system.

This DECT ULE FLD detector includes series of

messages for full communication administration

(Keep Alive, Tamper Status, Battery Status, Alert,

Configuration, etc.) as well as test transmission

signals.

FEATURES

 DECT ULE RF protocol.

 Low current Technology.

 Powered by a single 3V Lithium battery.

 Battery life: up to 4 years.

 Frequency Band: All DECT Standard Bands.

 Tamper Open/Close transmission.

 Keep Alive transmission.

 Battery status transmission.

 Bi-Color LED indications for monitoring &

Pairing.

 Range up to 500m on open space.

 Back tamper.

 Alarm triggered by the sensor on the edge of

the cable.

 Remotely configurable.

 Friendly Pairing and Installation processes.

OPERATION

The DECT ULE FLD detector transmits the

following events data:

KEEP ALIVE – A periodical transmission

indicating detector’s presence. The time interval is

configurable – the minimum value is 3 seconds.

ALARM – Alarm transmission triggered by the

Flood indicating on water leakage detection. The

Red LED will blink once.

LOW BAT – Whenever the battery reaches a pre-

set low level (~2.5V) Battery Low signal will be

sent. When the Battery level drops below Cut Off

level (~2.3V) the device will stop functioning and

the Red LED will constantly light On.

TAMPER – Whenever the DECT ULE FLD cover

is removed or tore off the wall, a message will be

transmitted with “Tamper” signal.

PREPARE THE DEVICE FOR

INSTALLATION

1. Open the screw cover and unscrew the holding

screw as shown in Figure 1.

2. Separate the device from the Bracket by tilting

the front cover as shown in Figure 1.

3. Break one piece of the Bracket corners

according to the device installation orientation

(Horizontal/Vertical) as shown in Figure 2.

4. Genteelly connect the Flood sensor cable to its

place as shown in Figure 3. Be aware that the

connector can be inserted in only one direction.

5. In case you wish to install the device using the

adhesive strips then attached them to the

device and to the Flood sensor.

6. Continue with the pairing process.

FIGURE 1 – SEPARATE FROM BRACKET

FIGURE 2 – DEVICE ORIENTATION

FIGURE 3 – INSERT THE CABLE

PAIRING PROCESS

1. Place a battery as instructed in Figure 4 and

wait until the Red LED stops blinking.

2. Initiate the Base Station pairing process.

3. Initiate the device pairing process by pressing

the pairing button for 5 seconds – the pairing

button is shown in Figure 5. The Green LED will

constantly turn On. When the Green LED starts

blinking release the pairing button.

4. The device should register to the Base Station.

5. When registration process is successfully

completed the Green LED will constantly light

On for 3 seconds and then turn Off.

6. If the registration process failed the Red LED

will blink (remove the battery and run the pairing

process again).

FIGURE 4 – BATTERY INSERTION

FIGURE 5 – PAIRING BUTTON

SELECT MOUNTING LOCATION

It is recommended to mount the device vertically on

a flat area to get maximum range.

As the detector is a wireless transceiver, and in

order to take full advantage of its sophisticated

operation, do not install the detector in areas where

large metal objects could interfere with the

transmission of signals.

TRANSMISSION TESTS

Tamper transmission test –

Changing the tamper switch state (by attaching /

removing the device to / from the Bracket) will

cause tamper transmissions. Verify receiving the

indication on your Application / Base Station.

Identification transmission test –

Use your Application / Base Station and send

Identification Request to the device. The device

will start blinking the Green & Red LEDs

alternately – 5 times each LED starting with the

Green LED.

Horizontal

Installation

Vertical

Installation

Summary of content (2 pages)

PAGE 1
2 DECT ULE-FLD FLOOD DETECTOR CR-DU-FLD EURO CR-DU-FLD USA ELECTRONIC ENGINEERING LTD. INTRODUCTION 3 FEATURES This DECT ULE FLD detector is an advanced, fully supervised low-current wireless detector that includes a DECT ULE transceiver for reliable system operation. A dedicated cable is supplied with this device. This DECT ULE FLD uses smart message control, which verifies that all messages are successfully transmitted, so that no event will be uninformed to the system.
PAGE 2
13 MOUNTING THE FLOOD SENSOR Mounting using adhesive tape: 1. Reveal first side of the smaller adhesive tape strip and attach it to the flood sensor (B). 2. Reveal the adhesive tape second side and attach the flood sensor to the wall. Mounting using screws: 1. Remove the screw cover (A) from the Flood sensor unit (B). 2. Mount the Flood sensor using the screw (C). In both cases: Mount the sensor at the desired fluid detection height from the floor (D).