User's Manual

Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This manual has instructions on how to
set up and register your new sensor. For
instructions on sensor settings, see the
user’s manual that came with your ULE
compatible products. Visit
www.vtechphones.com/wireless-monitoring
for a list of the latest ULE compatible products.
You may also view or download the online
User’s manual of the respective product
for a full set of installation and operation
instructions at www.vtechphones.com.
In Canada, visit www.vtechcanada.com.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Sensor unit overview
1 – Screw cover
Slide to open or close the screw
compartment case to reveal the
battery compartment case and
PAIRING button.
2 – Back cover
3 – LED light
Flashes red for a while when the
sensor is powered on.
Flashes red once when a motion is
detected.
Flashes green when the sensor is in
the registration mode.
4 – Motion detector
5 – PAIRING button
Press and hold to enter the
registration mode.
6 – Battery compartment case
•
•
•
•
•
Before use
Install battery to the motion
sensor
Flip the ribbon across the battery
compartment.
Insert the battery into the battery
compartment.
NOTES
Use only CR123A lithium battery.
While you insert the battery, make sure the
polarities are correct.
The battery operate properly under the
temperature between 0°F (-18°C) and 120°F
(49°C).
Add and register a sensor
Add your new VC7003 motion sensor to your
ULE compatible product. Visit
www.vtechphones.com/wireless-monitoring
for a list of the latest ULE compatible products.
Register each sensor to the respective ULE
compatible product before use.
To register a motion sensor:
Refer to the online User’s manual of your
ULE compatible product at
www.vtechphones.com/support/manuals
to enter the registration mode.
Use a narrow pointed object such as a
pencil to press and hold the PAIRING
button on the motion sensor, until the
LED light flashes green, to enter the
registration mode.
1.
2.
•
•
•
1.
2.
When the registration process completes, the
green LED light on the sensor will remain
steady for about two seconds, and then turn
off. The registration process takes about
90 seconds to complete.
NOTES
If the registration fails, take out the battery and
place it aside for a minute to reset the sensor.
Then, install the battery back and try the
registration process again.
Replacing a sensor
If you have purchased this new VC7003
accessory sensor to replace an old sensor,
follow the instructions to deregister your old
sensor.
To replace a sensor, you must deregister the
registered sensor first, and then register this
new sensor to your ULE compatible product.
Deregister a sensor or all sensors:
Refer to the online User’s manual of your
ULE compatible product at
www.vtechphones.com/support/manuals
to deregister a sensor or all sensors.
•
•
Motion detection range
The motion sensor can detect a motion
occurred at a distance of up to
40 feet (12 meters) from itself when it is
mounted at the height of 7.9 feet (2.4 meters).
It is recommended to mount the sensor at the
height between 6.2 feet (1.9 meters) and
7.5 feet (2.3 meters) for optimal detection
coverage.
NOTE
The numerical values in the following
illustrations are for conceptual reference only.
The actual angles and distances may vary upon
the change in the mounted height of the sensor.
•
For motion detection of babies or pets:
If you use the motion sensor only to detect
the motion of babies or pets, you can mount
the sensor at a lower position to shorten
the minimum distance before reaching the
detection area.
Check the sensor before use
The Motion sensor is more sensitive in
detecting motions crossing the space in front
of the sensor than that moving towards the
sensor.
Follow the steps below to check if you
receive alerts at your ULE compatible
product.
Refer to the Installation guide or user’s
manual of your ULE compatible product for
the sensor alerts.
1. Place the sensor on a stable flat surface.
2. Walk across the area in front of the sensor.
You will receive alerts at your ULE
compatible product.
The LED light on the motion sensor will
flash red once.
NOTE
Once motion is detected, the sensor will only
start to detect motion again after one minute.
•
•
•
Test the sensor signal strength
You can mount the motion sensor at a
location where family members or unwanted
visitors are likely to be coming and going.
1. Take the sensor to the desired mounting
location, and then hold it the desirable
height (Refer to Motion detection range
section).
2. Walk across the area in front of the sensor
again to make sure you receive alerts at
your ULE compatible product.
NOTES
If there is no alert received when you walk
across the area in front of the sensor, move
your ULE compatible product closer to the
mounting location or move the sensor closer to
the respective product.
Use adhesive tape to hold the sensor
temporarily in place.
Depending on surroundings and obstructing
factors, like walls or cabinets, the sensor may
not transmit to the ULE compatible product
properly.
•
•
•
VC7003
Accessory Motion Sensor
for use with
ULE certified systems*
User’s manual
Motion sensor
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
Mounting bracket
on mounting base
with screw
Lithium battery
Mount the sensor
NOTES
This sensor must be mounted vertically on wall. Do not mount the motion sensor in a horizontal
orientation, or flat on the ceiling.
Make sure the mounting surface is clean. A textured surface or any imperfections to a smooth surface
can keep the mounting tape from making a strong bond.
The recommended mounting height for motion detection of adults is between 6.2 feet (1.9 meters) and
7.5 feet (2.3 meters), and that for babies or pets is about 3.3 feet (1 meter).
If you drill the holes into an object other than a stud, insert the screw anchors into the holes and tap
gently on the ends with a hammer until the screw anchors are flush with the wall or ceiling.
TIP
You can choose to mount the sensor with the mounting tape first. Remove the mounting tape and use
screws later if you decide to mount it at that location for long term.
•
•
•
•
•
User’s
manual
User’s manual
2 3
4
1
Screw for
mounting
brackets x 2
Screw for
back cover x 3
Screw nut for
mounting base screw
Mount on the wall - with fixed angle
Mount on the wall - with adjustable detection angle
1
2 3
5
4
5 6
7
(Optional)
(Optional)
2
1
P
P
P
P
a
b
i
k
l
m
c
d
e
f
g
h
j
n
o
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Insert screw
anchors if
necessary.
Insert screw
anchors if
necessary.
*
Visit www.vtechphones.com/wireless-monitoring for the latest ULE compatible products.
Anchor for
back cover x 3
Anchor for
mounting
brackets x 2
Double-sided
mounting tape
Mount with tape
Mount on the wall - with fixed angle
Mount with screws
4 5
2
3
1
Drill a hole
here.
This product requires professional installation in accordance with UL 681.
Up to 34.4 feet
(10.5 meters)
Side view
Detection
area
78
o
Top view
Shooting area
19.7 inches
60 degrees
22.8 inches
Shooting area
19.7
inches
50 degrees
18.3
inches
63 inches
87
o
Detection area
1.3 feet
(0.4 meter)
10
o
Height: 6.9 feet (2.1 meters)
Height: 6.9 feet (2.1 meters)
Side view
Detection
area
78
o
Top view
87
o
Detection area
0.7 feet
(0.2 meter)
10
o
Height: 3.3 feet (1 meter)
Up to 16.4 feet
(5 meters)
Height: 3.3 feet (1 meter)
TIP
You can mount the sensor next to the corner of wall, and then rotate it 45 degree for optimal detection coverage.•