INSTALLATION MANUAL N2 NANO POWER Octa Band Digital Radios 20dBm per Band Integrated Antennas Integrated Bluetooth
NANO POWER 20dBm Octa Band Digital Radio Revision History Revision Number 1.0.1 Revision Date st 1 June 2019 Summary of Changes Author New Format Allen Chu Copyright © 2019 Sunwave All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from Sunwave.
NANO POWER 20dBm Octa Band Digital Radio Content General......................................................................................................................................................................................................... 5 Warnings.............................................................................................................................................................................................. 5 Site Considerations...............................
NANO POWER 20dBm Octa Band Digital Radio N2RU Ceiling Installation (without suspended ceiling)....................................................................................................................... 21 Draw Circles for plastic expansion nails......................................................................................................................................21 Assemble Mounting Bracket.............................................................................................
NANO POWER 20dBm Octa Band Digital Radio General The CrossFire system components are designed for maximum safety and reliability when they are installed, used, and maintained by trained and qualified technicians in accordance with the procedures and instructions contained in this manual. To assure the safe operation of your system, always follow the safety and operational recommendations in this manual. Warnings CrossFire is not a consumer product.
NANO POWER 20dBm Octa Band Digital Radio If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
NANO POWER 20dBm Octa Band Digital Radio Preparation Unpacking and Inspection Unpack and inspect the packages as the following procedure: 1. Open the shipping packages carefully for each unit from the protective packing sponge. 2. Ensure that all equipment and accessories have been delivered. 3. Ensure that all equipment and accessories have no damage. If there is any damage, contact your Sunwave service agent. A2 Accessories Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.
NANO POWER 20dBm Octa Band Digital Radio EU-O Accessories Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
NANO POWER 20dBm Octa Band Digital Radio N2 Accessories Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
NANO POWER 20dBm Octa Band Digital Radio Tools Electric drill, cross screw, cutter, ladder and other tools are needed for N2RU installation which are not offered from Sunwave for now. All of these tools are for customers to prepare Philips Screwdriver M6 and M3 Drilling Machine Pen Allen Wrench T5 Combination Spanner 17mm N2RU Power Supply For CrossFire N2RU system, it needs DC power to supply N2RU at remote side. Here are 2 methods for power supply – AC/DC power adapter and power supply unit (PSU).
NANO POWER 20dBm Octa Band Digital Radio Here is some specification for cable design power supply unit (PSU): Pn = 78W Power consumption of N2RU Pw = 22W If N2 consumes 95W then 5W is dissipated in the wire (Pw) Pin = Vin*Iin = 100W Pin = 100W max for class 2 installation Rw = Pw/Iw2 = 6.8992 Rw = resistance of the wire Vin = 56V Voltage of N2 PSU Iin = Pin/Vin = 1.
NANO POWER 20dBm Octa Band Digital Radio Installation of the A2 Mount the A2 in the Rack Attach A2 handle 1. Attach the 19" mounting brackets at the front of the A2, using 4 screws M3×16 per bracket and the Phillips screwdriver. Observe the orientation of the brackets (Figure 2). 1. Attach the sliding rails Ⓑ to the rack (Figure 3) Note: the sliding rails is not included in delivery. 2. Place the A2 in the rack (Figure 4) Figure 2.
NANO POWER 20dBm Octa Band Digital Radio 3. Secure the A2 using 2 screws M6×16 on both side and the Phillips screwdriver (Figure 5). Figure 5. Fix A2 with Screws For rack installation, it is highly recommended to use fan in the middle of 2 adjacent A2. Figure 6. Separation of adjacent A2s Connect power and ground cable to A2 1. Connect and lock the power cable at the A2 rear side (Figure 7). 2. Connect and screw the ground wire at the A2 rear side (Figure 8). Figure 7.
NANO POWER 20dBm Octa Band Digital Radio Mount the A2 on the Wall Attach handle to A2 Attach the 19" mounting brackets to the A2 rear, using 4 screws M3×16 per bracket and the Phillips screwdriver. Observe the orientation of the brackets shown in Figure 9. Figure 9. Attaching a 19" Mounting Bracket Mount A2 to wall 1. Hold the A2 to the installation location and mark the position of the 4 mounting holes in the mounting brackets; see arrows in Figure 10 2.
NANO POWER 20dBm Octa Band Digital Radio Connect power and ground cable to A2 1. Connect and lock the power cable at the A2 rear side (Figure 12) 2. Connect and screw the ground wire at the A2 rear side (Figure 13) Figure 12. Connect power cable at rear side Figure 13. Connect ground cable at rear side Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
NANO POWER 20dBm Octa Band Digital Radio Installation of the EU-O Installing the EU-O is virtually the same as installing the A2. Please refer to the steps described in A2 installation for the EU-O. Mount the EU-O in the Rack Proceed as described under Mount the A2 in the Rack to mount the EU-O in the rack and connect the power and the ground cable.
NANO POWER 20dBm Octa Band Digital Radio Installation of the N2RU N2RU Ceiling Installation (with suspended ceiling) Assemble Bracket I&II 1. Assemble Mounting Bracket I & IV with 6 x M3 x 6 screws. Figure 14. Assembling bracket I & bracket II 2. Lace Bracket I & IV combo with Nylon Cable Tie Figure 15. Lacing Mounting Bracket Place the bracket 1. Drill a hole with diameter of 90mm for putting Mounting Bracket I & IV on ceiling upside. Figure 16. Drilling a Hole Contact us today: www.
NANO POWER 20dBm Octa Band Digital Radio 2. Lay Mounting Bracket I & IV at ceiling upside for immobilization of N2RU. Figure 17. Placing bracket 1 3. Make the nylon tie hang down through the hole. Figure 18. Placing bracket 2 Assemble Bracket II 1. Assemble Mounting Bracket II to Mounting Bracket I using 2 X M6 X 70 screws, Flat Washer M6 and Spring Washer M6. Note: Mounting Bracket III is already assembled into N2RU in factory Figure 19. Assemble bracket II Contact us today: www.sunwaveglobal.
NANO POWER 20dBm Octa Band Digital Radio Buckle Up and Connect Wire 2. Buckle the bar side of N2RU up to Mounting Bracket III. Figure 20. Buckle up 3. Connect power cable and fiber cable to N2RU Figure 21. Wire Connection Diagram 4. Buckle the rotary hook side of N2RU to Mounting Bracket III Figure 22. Installation Completed Diagram Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
NANO POWER 20dBm Octa Band Digital Radio 7. Tighten the M3 x 3 screws Figure 23. Tighten N2RU To perform maintenance on the N2RU 1. Press the button of hook at N2RU to expose top panel of N2RU for debugging and maintenance Figure 24. Unlock Rotary Hook Diagram 1 Figure 25. Unlock Rotary Hook Diagram 2 Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
NANO POWER 20dBm Octa Band Digital Radio N2RU Ceiling Installation (without suspended ceiling) Draw Circles for plastic expansion nails 1. Using the Mounting Bracket III keyholes as guides, mark the position of the 2 holes to be drilled Into the ceiling. Figure 26. Drawing Circles Diagram 1 2. Drill 2 holes with diameter of 10mm and depth of 55mm at the position in step 1 Figure 27. Drilling Holes Diagram 1 3. Insert plastic expansion nails into holes by hammer Figure 28.
NANO POWER 20dBm Octa Band Digital Radio Assemble Mounting Bracket 1. Assemble Mounting Bracket III to ceiling using ST6.3 X 50 screws. Figure 29. Assembling Bracket III Diagram 1 Figure 30. Assembling Bracket III Diagram 2 Buckle Up and Connect Wire 2. Buckle the bar side of N2RU up to Mounting Bracket III. Figure 31. Buckle up Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
NANO POWER 20dBm Octa Band Digital Radio 3. Connect power cable and fiber cable to N2RU Figure 32. Wire Connection Diagram 4. Buckle the rotary hook side of N2RU to Mounting Bracket III Figure 33. Installation Completed Diagram 7. Tighten the M3 x 3 screws Figure 34. Tighten N2RU Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
NANO POWER 20dBm Octa Band Digital Radio To perform maintenance on the N2RU 1. Press the button of hook at N2RU to expose top panel of N2RU for debugging and maintenance Figure 35. Unlock Rotary Hook Diagram 1 Figure 36. Unlock Rotary Hook Diagram 2 Contact us today: www.sunwaveglobal.com marketing@sunwaveglobal.com © Sunwave IM_CF_N2 v1.0.
