CLASSICAL TURNTABLE WITH AM/FM RADIO CD, CASSETTE RECORDER & USB/SD SLOT MODEL: CR7014A-BK Operating Instructions Manual
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS 1) Please read these instructions and keep them for future reference. 2) Pay attention to all warnings. 3) Follow all instructions. 4) Do not use this apparatus near water. 5) Clean only with a dry cloth.
Avoid installing this unit in places exposed to direct sunlight or close to heat radiating appliances such as electric heaters, on top of other stereo equipment that radiates too much heat, places lacking ventilation or dusty areas, places subject to constant vibration and/or humid or moist areas. Do not attempt to clean this unit with chemical solvents as this might damage the finish. Use a clean dry cloth. Operate controls and switches as described in the manual.
LOCATION OF CONTROLS AND INDICATORS 1) Dust Cover 10) Function Selector Button 2) Cassette Door 11) CD/USB/SD Playback Control Button 3) Speaker 12) Disk Tray Door 4) Cassette Button 13) CD-Rom Open/close button 5) BT indication light 14) 3.
PHONOGRAPH 21) 45 rpm adaptor 22) Lift lever 23) Auto stop control 24) Tone arm lock 25) Speed selector (33/45/78 rpm) 26) Tone arm REMOTE CONTROL 27) Mute button 28) Program button 29) Repeat button 30) Function Mode button CD/USB/SD/BT 31) Skip down button 32) Play/Pause button 33) Record button 34) Stop 35) Skip up button button 36) Folder up button 37) Folder down button NOTE: All the buttons on the remote control just use for CD/USB/SD /BT function.
OPERATING INSTRUCTIONS Listening to radio 1. Turn the volume knob in a clockwise direction to turn the equipment on. 2. Use the function selector to select TUNER mode. 3. Use the radio band selector to select the desired band (AM, FM or FM-Stereo). 4. Turn and hold the tuning knob for a few seconds to tune into a radio station. The unit will start searching automatically and stop when a radio station is found. Release the knob once a station has been found. 5.
Phono Operation 1. Open the dust cover and turn the volume knob clockwise to turn the equipment on. 2. Use the function selector to select PHONO mode. 3. Set the speed selector to the appropriate position: 33, 45 or 78, depending on the record to be played. 4. Set the auto stop control to ON if you want the turntable to stop turning when it has reached the end of the record. If the switch is set to OFF, the turntable will continue turning at the end of the record. 5.
Phono encoding 1. Set the function button to PHONO mode and then insert a memory device (USB drive, SD or MMC card). 2. Put your record onto the turntable and get it ready for playback. 3. Press the record REC button. It will take about 3 - 4 seconds to read the memory device, then the USB or SD icon will be flashing on the LC display. 4. Press the skip up or skip down button to select the desired mode (USB or SD) for encoding, then press the record REC button again to confirm.
3. Cassette PlayBack Control Operating 1) TAPE Play: a) Function Choose to “TAPE” mode---Push “EJECT” key under tape----Open cassette tape door-----put your tape into cassette dock----Manual close the tape door –Press “PLAYER” Key ------ To adjust the volume level for your preference, turn the volume knob to the right or left b) Press “PAUSE” button once to stop playing, press it again to continue C) When TAPE tracks play ending, “PLAYER” Key up automatically.
Cassette encoding 1. Set the function button to TAPE/AUX mode and then insert a memory device (USB drive, SD or MMC card). 2. Press the record REC button, it will take 3 - 4 second to read the memory device, then the USB or SD icon will be flashing on the LC display. 3. Press the skip up or skip down button to select the desired mode (USB or SD) for encoding, then press the record REC button again to confirm. (You can skip this step if only a USB drive or an SD/MMC card is inserted.) 4.
CD Operation 1. Turn the volume knob clockwise to turn the equipment on. 2. Press the CD-Rom switch ,then the disk tray door opens . 3. Place the CD face up inside ,making sure it is fully placed .Then press the CD-Rom switch again ,the disk tray door closes . 4. To play a different piece on the record, Press the skip up or skip down button to select the desired piece. 5 To adjust the volume level, turn the volume knob to the right or left. CD encoding 1.
2. Following the illustration below, insert a USB device face up into the USB port, making sure it is fully inserted. Alternatively, insert a memory card in the direction of the arrow (as shown on the label next to the memory card slot), making sure to insert it straight without bending. IMPORTANT: Connecting the USB device upside down or backwards could damage the audio system or storage media (USB drive, SD or MMC card). Check to ensure the direction is correct before connection. 3.
Important notes ⚫ The system can detect and read files in MP3 / WMA format only via the USB port or SD card slot. ⚫ You can connect an MP3 player to the system via the USB socket, however, some MP3 players may not be able to play via the USB socket. This is due to variances in the MP3 encoding format; it is not a malfunction of the system. ⚫ There are numerous USB and SD device producers and their products vary in solution and format.
Copying a single file/track 1. Insert a USB storage device and SD/MMC card, then select USB/SD mode (as described previously). 2. Press the record REC button during playback of the track you want to copy: “ONE” will be flashing on the display. Press the record REC button again to confirm. 3. The USB or SD icon will be flashing on the display while the system is copying the file. 4. Once the file has been copied, the unit will stop playback automatically.
Deleting files from the USB device / SD card The system is able to erase files stored on the USB drive or SD card. You can delete a single file/track, a folder of files/tracks, or all files/tracks on the storage medium. Deleting a single file/track 1. Insert the USB storage device or SD card, then select USB/SD mode (as described previously). 2. Press the delete DEL button during the playback of the track you want to delete: “ONE” will be flashing on the display.
NOTE: Pressing the delete DEL button will completely delete all files/tracks on the USB device or SD card. Removing the USB device / SD card ⚫ First move the function selector to another mode (tuner, phono, tape), then turn the volume knob counterclockwise to turn off the power. ⚫ To remove a USB device, pull it out of the USB port. ⚫ To remove a memory card, press the memory card inwards and then release it. The card will be released (partially ejected) and you can remove it by hand.
3. Press the skip up or skip down button to select the desired mode (USB or SD) for encoding, then press the record REC button again to confirm. (You can skip this step if only a USB drive or an SD/MMC card is inserted.) 4. The system will start the encoding mode after a few seconds. During encoding, the USB or SD icon will be flashing on the display. 5. To finish encoding, press the stop button. The display will show “END” and return to PHONO/AUX mode. NOTE: ⚫ The recording speed is 1:1.
Bluetooth input -Receiver Listening to iPhone (or other Bluetooth input devices) 1. Turn the volume knob clockwise to turn the equipment on. 2. Press” PHONO/ AUX/BT IN” on panel for 3 times. ( 1st =Phono , 2nd =AUX , 3rd BT ) or Press mode on remote controller. LCD shows” BT” and flashing. When succeed in connecting, LCD shows “BT” and stable. 3.
Troubleshooting Guide If you are experiencing problems with your USB Turntable with Cassette Deck and Radio, check in the section below whether there are any quick and easy checks you can do that may help you solve the problem. If you cannot solve the problem by yourself, contact our after-sales support line for advice. Do not attempt to open, repair or modify the equipment yourself. Problems with sound ⚫ Clockwise rotate the power/volume knob to increase the volume.
FCC WARNING STATEMENT Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.