PART LIST Top Panel Left Side Panel | Right Side Panel Bottom Panel Door Panel 1PC 1PC 1PC 1PC 1PC Back Panel Adjustable Shelf Leg 1PC 1PC PCS
HARDWARE LIST ADDITIONAL TOOLS (Not Provided) Note: It is not recommended to use power tools during assembly.
Step 1. Attach magnet (part #10) to top panel (part A) using screws (part #13) and fillips head screwdriver. Insert cam bolts (part #3) into per-drilled holes of top panel (part A), left side panel (part B) and right side panel (part C) using fillips head screwdriver. Attach door hinges (part #2) to door panel (part E) using long screws (part #6) and fillips head screwdriver. NOTE: Do not over tighten cam bolts. Stop tightening once threads on cam bolt are no longer visible.
Step 2. Attach legs (part H) to bottom panel (part D) using Allen bolts (part #1) and Allen wrench (part #11). Step 3. Attach metal wires (part #14) to bottom panel (part D) using hex nuts (part #15) and wrench (part #12). Insert cam bolts (part #3) into the per-drilled holes of bottom panel (part D) using fillips head screwdriver. NOTE: Do not over tighten cam bolts. Stop tightening once threads on cam bolt are no longer visible.
Step 4. Attach back panel (part F) to left side panel (part B) and right side panel (part C) using cam locks (part #4), wood dowels (part #5) and fillips head screwdriver. NOTE: Cam locks must rotate full 180°. See pictured insert. point ar O cam lock to ward adjacent 5 & A 172 tum clockwise to fasten #5 Step 5. Attach bottom panel (part D) to left side panel (part B}, right side panel (part C) and back panel (part F} using wood dowels (part #5), cam locks (part #4) and fillips head screwdriver.
Step 6. Carefully turn unit upright. Insert cam locks (part #4) into the per-drilled holes on the bottom of back panel (part F) and lock using fillips head screwdriver. NOTE: Cam locks must rotate full 180°. See pictured insert. ward adjacent 25 & A 172 tum clockwise to fasten i @ x2 Step 7. Attach top panel (part A) to left side panel (part B), right side panel (part C) and back panel (part F) using wood dowels (part #5), cam locks (part #4) and fillips head screwdriver.
Step 8. Insert shelf holders (part #8) into desired position and slide adjustable shelf (part G) into place. #9 o x4 Step 9. Attach door panel (part E}) to left side panel (part B) using long screws (part #6) and fillips head screwdriver at door hinge (part #2). Then attach handle (part #7) to door panel (part E) using round head bolts (part #8) and fillips head screwdriver.
3/4" D8 x Safety Strap Kit| Wall Anchor Washer Short Screw Long Screw | Safety Wall Strap| 1PC 1PC PCS 1PC 1PC 1PC SAFETY WALL STRAP INSTALLATION Note: It is highly recommended to install this safety strap kit to prevent tipping, damage and/or injury. 1. Insert short screw (C) through washer (B) and safety wall strap (E) and attach to back of top panel (part A) using fillips head screwdriver. 2. Drill a hole where you want to secure the unit.
ADJUST YOUR DOORS TO MAKE THE GAPS MORE EVEN (OPTIONAL). STEP Open the door TOP PANEL STEP 2 STEP 2a MOVE DOOR IN STEP 2b MOVE DOOR OUT Adjust the gap between door panel and side panel \ \ TOP PANEL TOP PANEL SIDE PANEL too small gap SIDE PANEL big gap DOOR TOP PANEL TOP PANEL TOP PANEL Loosen the screw indicated a little, adjust the hinge to right position {(see step 2a & 2b), then tighten the screw. Push the hinge back a little. Pull the hinge forward a little.