Installation Instructions
8 9
X2
* Touch control located on the right side.
10. ACCEPTING / MAKING A CALL WHILE PLAYING MUSIC
1) Accepting a Call
- When the incoming call tone is heard through the headphones, tap touch panel twice quickly or press the POWER
button. (Volume control : While on a call, use the touch panel to control volume)
2) Ending a Call
- While on a call, shortly pressing the POWER Button or tap touch panel twice quickly to end the call.
3) Rejecting a Call
- When the incoming call tone is heard through the headphones, press and holds the POWER Button for about 1
second.
(After hearing the ‘beep’ signal tone, the incoming call is rejected and the voice guidance “Call Ignored” is heard.)
4) Call Waiting
- When there is another incoming call while on a call.
(Supported only when having applied for this service with your telecom provider.)
- Press and hold the POWER Button for about 1 second to place the current call on call waiting and connect the
second call.
(Press the POWER Button again for about 1 second to switch between the waiting call and connected call.)
- Shortly press the POWER Button to end the current call and connect the second call.
5) Switching between the Device and Mobile Phone
- To switch the call from mobile phone to the headphone, press the POWER Button for 1 second.
1) Playing Music
- Double tap touch panel or Press the POWER button for about
1 second to play music from the ‘Bluetooth Device’
- While music is playing , double tap touch panel or Press the
Power button for about 1 second to pause the playing music.
The music will be played from the paused point when playing
music again.
1) Accepting a Call while Playing Music
- When the incoming call tone is heard through the headphone, tap touch
panel twice quickly or press the POWER button. The music will be paused
and the call is connected.
- Once the call has ended,, tap touch panel twice quickly or press the
POWER button to terminate the call. Once the call is terminated, the
paused music will play again.
8. LISTENING TO MUSIC (PLAY & CONTROL)
9. LISTENING TO MUSIC (PLAY & CONTROL)
* SBC(Sub Band Codec) is default audio codec installed for any ‘Bluetooth Device’.
* aptX and AAC are high quality audio codec.
2) Controlling Volume and Using Seek
- Sweep the touch panel to top (Vol +) / bottom (Vol-) to control the volume.
- Sweep the touch panel to forward (FF) / backward (REW) to go to the next / previous song.
* Music can be listened to through 900 LEGACY by directly operating your ‘Bluetooth Device’.
* When the battery is completely drained, you can connect the provided microphone cable to continue listening.
3) Smart Play / Pause
- 900 LEGACY has Smart Play / Pause function which can detect whether the headphone is being worn or not.
- The function can play or pause music automatically.
(Play when headphones are worn on the ears/Pause when the headphones are removed from the ears).
- To continue playing music when the headphones are not worn on the ears, double tap the touch panel or press
the Power button.
Call Button
OR
Status LED Indicator
Incoming Bell/Outgoing Bell Purple light blinks in 1.5 second intervals
During Call Blue light slowly blinks every 6 seconds
When there are two calls connected Purple light slowly blinks every 6 seconds
※ Battery use time
* The above times may differ depending on the environment in which it is used.
Status Noise Cancelling ‘OFF’ Noise Cancelling ‘ON’
Call Time Max. 41 hours Max. 39 hours
Music Play Time Max. 46 hours Max. 43 hours
Standby Time Max. 329 hours Max. 320 hours
10 min. charging Max. 4 hours Max. 4 hours
Full Charging Time about 3.3 hours
X2
32:(5
1&
Answer Call
1) Double tap touch panel or
2) Press the POWER button
for about 1 second.
Play / Pause
1) Double tap touch panel or
2) Press the POWER button
for about 1 second.
X2
X2