Crestron HD-SCALER High-Definition Video Scaler Operations & Installation Guide
Regulatory Compliance As of the date of manufacture, the HD-SCALER has been tested and found to comply with specifications for CE marking. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Crestron HD-SCALER High-Definition Video Scaler Contents High-Definition Video Scaler: HD-SCALER 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications................................................................................................................. 4 Specifications .
Crestron HD-SCALER High-Definition Video Scaler High-Definition Video Scaler: HD-SCALER Introduction The HD-SCALER provides a simple and cost-effective universal scaler solution with advanced features for adapting any digital HD display, projector, or codec to handle virtually any video signal regardless of resolution or format. The compact, low-profile design of the HD-SCALER allows it to be installed discreetly behind a flat-panel display, above a ceiling projector, or in the back of an equipment rack.
Crestron HD-SCALER High-Definition Video Scaler Features and Functions (Continued) • • • • Includes built-in test patterns for precise display setup Allows control system integration via Cresnet® Affords a seamless upgrade for Crestron MPS and QuickMedia® systems Provides a powerful portable diagnostic tool for any video setup Universal HD Scaler The HD-SCALER connects to the HDMI or DVI input of a video display.
Crestron HD-SCALER High-Definition Video Scaler Built-In Test Patterns To ensure optimum performance and proper setup without necessitating any additional test equipment, the HD-SCALER includes a complete assortment of professional video test patterns. These include various color bars, line and grid patterns, RGB and grayscale ramps, streak and streak boost, raster, solid colors, and several aspect ratio boxes. Even as a portable device, the HD-SCALER provides an invaluable setup tool.
High-Definition Video Scaler Crestron HD-SCALER Applications The diagram below shows an HD-SCALER in a typical application. HD-SCALER in a Typical Application 4 • High-Definition Video Scaler: HD-SCALER Operations & Installation Guide – DOC.
Crestron HD-SCALER High-Definition Video Scaler Specifications Specifications for the HD-SCALER are listed in the following table.
Crestron HD-SCALER High-Definition Video Scaler HD-SCALER Specifications (Continued) SPECIFICATION DETAILS Input Resolutions HDMI and DVI, Progressive (Continued) 1920 x 1200 @ 60 Hz 2048 x 1080 @ 24 Hz 2048 x 1152 @ 60 Hz plus any other resolution up to 165 MHz pixel clock HDMI and DVI, Interlaced 720 x 480 @ 30 Hz (480i) 720 x 576 @ 25 Hz (576i) 1920 x 1080 @ 25 Hz (1080i25) 1920 x 1080 @ 30 Hz (1080i30) plus any other resolution up to 165 MHz pixel clock RGB 640 x 480 @ 60 Hz 720 x 480 @ 60 Hz (
Crestron HD-SCALER High-Definition Video Scaler HD-SCALER Specifications (Continued) SPECIFICATION DETAILS Scaler Output Resolutions Progressive 640 x 480 @ 60 Hz 720 x 480 @ 60 Hz (480p) 720 x 576 @ 50 Hz (576p) 800 x 600 @ 60Hz 848 x 480 @ 60Hz 1024 x 768 @ 60 Hz 1280 x 720 @ 50 Hz (720p50) 1280 x 720 @ 60 Hz (720p60) 3 1280 x 768 @ 60 Hz 3 1280 x 800 @ 60 Hz 1280 x 960 @ 60 Hz 1280 x 1024 @ 60 Hz 1360 x 768 @ 60 Hz 3 1366 x 768 @ 60 Hz 3 1400 x 1050 @ 60 Hz 3 1440 x 900 @ 60 Hz 4 1600 x 900 @ 60 Hz
Crestron HD-SCALER High-Definition Video Scaler HD-SCALER Specifications (Continued) SPECIFICATION DETAILS Audio (Continued) Performance (Analog) Frequency Response 20 Hz to 20 kHz ±0.75 dB S/N Ratio >90 dB, 20 Hz to 20 kHz A-weighted THD+N <0.05% @ 1 kHz (line) Stereo Separation >90 dB Communications Cresnet Supports Cresnet slave mode for control HDMI Passes CEC, manages EDID, supports HDCP USB For console, USB 2.
Crestron HD-SCALER High-Definition Video Scaler HD-SCALER Specifications (Continued) SPECIFICATION DETAILS Available Accessories CBL-AUDIO Crestron Certified Mini-TRS Stereo Audio Interface Cable CBL-HD Crestron Certified HDMI Interface Cable CBL-HD-DVI Crestron Certified HDMI to DVI Interface Cable CBL-HD-LOCK Locking High-Speed HDMI Cable CBL-VGA Crestron Certified Computer VGA Interface Cable CBL-VGA-AUD Crestron Certified Computer VGA Interface Cable with Mini-TRS Audio CRESNET Cresnet
High-Definition Video Scaler Crestron HD-SCALER Physical Description This section provides information on the connections, controls, and indicators available on the HD-SCALER. HD-SCALER Physical Views (Left and Right Sides Shown) 10 • High-Definition Video Scaler: HD-SCALER Operations & Installation Guide – DOC.
Crestron HD-SCALER High-Definition Video Scaler HD-SCALER Overall Dimensions (Front and Right Side Views) 6.89 in (175 mm) 7.36 in (187 mm) 5.25 in (134 mm) 1.24 in (32 mm) 7.43 in (189 mm) HD-SCALER Connectors, Controls, and Indicators (Left and Right Side Views) 1 2 9 10 3 4 11 5 6 7 12 14 13 15 8 Operations & Installation Guide – DOC.
Crestron HD-SCALER High-Definition Video Scaler Connectors, Controls, and Indicators 1 # CONNECTORS, CONTROLS, AND INDICATORS DESCRIPTION 1 AUDIO IN (1) 3.5 mm TRS mini phone jack; Unbalanced stereo line-level audio input; Input Impedance: 10 kilohms; Input Level: 2 Vrms maximum 2 RGBHV IN (1) DB15HD female, RGB (VGA), component, S-video, or composite video 2 input; Formats: RGBHV, RGBS, RGsB, YPbPr, Y/C, NTSC, PAL; Input Levels: 0.5 to 1.
Crestron HD-SCALER High-Definition Video Scaler Connectors, Controls, and Indicators (Continued) 1 # CONNECTOR6 CONTROLS, AND INDICATORS 11 IR IN 12 HDMI OUT LED (1) Green LED, indicates output signal presence 13 HDMI IN LED (1) Green LED, indicates HDMI input is selected 14 RGB IN LED (1) Green LED, indicates RGB input is selected 15 PWR LED (1) Green LED, indicates 24 Vdc power supplied via Cresnet network or local power pack DESCRIPTION (1) IR receiver window for use with remote prov
Crestron HD-SCALER High-Definition Video Scaler Setup Network Wiring When wiring the Cresnet network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. CAUTION: Failure to use Crestron power supplies could cause equipment damage or void the Crestron warranty. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment.
Crestron HD-SCALER High-Definition Video Scaler Installation Ventilation The HD-SCALER should be used in a well-ventilated area. The venting holes should not be obstructed under any circumstances. To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications. Mounting the HD-SCALER The HD-SCALER mounts on a flat surface such as a wall or ceiling. The HD-SCALER can also be mounted on a rack rail.
Crestron HD-SCALER High-Definition Video Scaler Rack Mounting To mount the HD-SCALER on the front or rear rail of a rack, do the following: 1. Position either mounting flange of the HD-SCALER so that the holes align with the holes in the rack (refer to the illustration below). 2. Secure the device to the rack using two rack mounting screws (not included).
Crestron HD-SCALER High-Definition Video Scaler Hardware Hookup Make the necessary connections as called out in the following illustrations. Refer to “Network Wiring” on page 14. Apply power after all connections have been made.
Crestron HD-SCALER High-Definition Video Scaler Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, firmware) can be transferred to the device.
Crestron HD-SCALER High-Definition Video Scaler 3. From the list in the Address Book, select the entry listed for the HD-SCALER (the address is listed as USB), and then click OK. The HD device list is displayed, and the checkbox of the HD-SCALER firmware is automatically selected. 4. Click Update. 5. After the process is complete, click Recheck to verify the upgrade. Operations & Installation Guide – DOC.
Crestron HD-SCALER High-Definition Video Scaler IR Remote Operation The HD-SCALER is shipped from the factory with an IR remote (refer to the illustration below). HD-SCALER IR Remote To operate the remote, point it at the IR IN receiver window on the HD-SCALER and press the appropriate buttons. Refer to the table below for descriptions of the buttons.
Crestron HD-SCALER High-Definition Video Scaler IR Remote Buttons (Continued) BUTTON DESCRIPTION EDID DFLT/COPY Specifies whether the analog/digital input EDID is to be set to DFLT in which the HD-SCALER sends a list of default resolutions to the source or set to COPY in which resolutions are read from the display and sent to the source. NOTE: If RGB video has been selected by pressing the RGB video button on the remote, then the analog input EDID is set.
Crestron HD-SCALER High-Definition Video Scaler On-Screen Display The HD-SCALER on-screen display (OSD), which appears on the display device, allows configuration of input and output signal parameters and also provides access to information about the HD-SCALER. The main menu of the HD-SCALER OSD is shown below. HD-SCALER OSD Main Menu As shown above, the main menu of the HD-SCALER OSD consists of five items: 1.
Crestron HD-SCALER High-Definition Video Scaler HD-SCALER OSD Menu Tree HD-SCALER On-Screen Display Menu Digital Input Analog Input Device Information Output Auto Calibrate Contrast Resolution Contrast Brightness Underscan Brightness EDID Test Patterns Horizontal Position Overscan EDID Video Info Vertical Position Signal Information EDID Audio Info Phase Coarse Restore Defaults Signal Information Phase Fine Color Red Color Green Color Blue EDID Overscan Source Control Signal Info
Crestron HD-SCALER High-Definition Video Scaler The following provides an overview of OSD operation using the IR remote: • To access the OSD, press MENU. Pressing MENU a second time closes the OSD. • To navigate up or down in a menu or in a list of available configuration or . settings, use • To select a highlighted item in a menu or in a list of available configuration settings, press OK. • To go back to the previous level (for example, to a submenu or to the main menu), use .
Crestron HD-SCALER High-Definition Video Scaler Configuration Configuration of input and output signals is performed from the HD-SCALER OSD using the supplied IR remote. For information about the remote, refer to “IR Remote Operation” on page 20. Configuring Analog Input Parameters To configure analog input parameters, navigate to the Analog Input main menu item and then press OK on the IR remote. The Analog Input submenu appears as shown below.
Crestron HD-SCALER High-Definition Video Scaler • Overscan: Sets overscan to None (default), 2.5%, 5.0%, or 7.5%. • Source Control: Sets the video input signal type: Auto, RGB, YPbPr, S-Video, CVBS, or CVBS (VCR mode). When set to Auto, only RGB and component video signals are automatically detected. In addition, the Signal Information menu item provides display of analog input signal information.
Crestron HD-SCALER High-Definition Video Scaler Configuring Output Parameters To configure output parameters, navigate to the Output main menu item and then press OK on the IR remote. The Output submenu appears as shown below. Output Submenu The Output submenu allows configuration of the following parameters: • Resolution: Sets the video output resolution. NOTE: When Resolution is set to Automatic (default setting), the preferred resolution of the display is used.
Crestron HD-SCALER High-Definition Video Scaler Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. HD-SCALER Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION PWR LED does not illuminate. Device is not receiving power. Verify connection via the Cresnet network or from the included power pack. HDMI IN LED does not illuminate.
Crestron HD-SCALER High-Definition Video Scaler The wire gauge and the Cresnet power usage of the run should be used in the following equation to calculate the cable length value on the equation’s left side. Cable Length Equation 40,000 L< RxP Where: L = Length of run (or chain) in feet R = 6 Ohms (Crestron Certified Wire: 18 AWG (0.75 mm2 )) or 1.
Crestron HD-SCALER High-Definition Video Scaler Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron HD-SCALER High-Definition Video Scaler This page is intentionally left blank. Operations & Installation Guide – DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 7136B (2029518) 04.14 Specifications subject to change without notice.
