Crestron MNET-CWD1012 Two-Way RF Transceiver Module Hardware Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc.
Crestron MNET-CWD1012 Two-Way RF Transceiver Module Contents Two-Way RF Transceiver Module: MNET-CWD1012 .................................. 1 Introduction................................................................................................................................1 Functions and Features ................................................................................................1 Specifications ..........................................................................................
Crestron MNET-CWD1012 Two-Way RF Transceiver Module Two-Way RF Transceiver Module: MNET-CWD1012 Introduction Functions and Features The MNET-CWD1012 (hereafter referred to as “module”) is a two-way radio frequency (RF) module that utilizes the 2.4 GHz frequency band to communicate with other devices. The module operates according to the IEEE 802.15.4 specification and can be configured to minimize the possibility of interference with other devices.
Two-Way RF Transceiver Module Crestron MNET-CWD1012 Specifications The table below is a summary of specifications for the MNET-CWD1012. Specifications of the MNET-CWD1012 SPECIFICATION DETAILS Power Requirements 0.75 Watts (5VDC @ 0.150A) Operating Frequency 2400 MHz to 2483.6 MHz (802.15.4 compliant) Operating Ranges¹ Minimum Distance 3 ft Maximum Distance Indoors (without repeater device) 100 ft Available Channels 16 (numbered 11 through 26 per 802.15.
Crestron MNET-CWD1012 Two-Way RF Transceiver Module MNET-CWD1012 Detail Views Ports The module contains two ports. Refer to the diagrams and descriptions that follow. Power/I-O A Crestron JDSM31M-1 31 pin, male, SMT interface connector provides power to the module as well as serial communications between the module and wired devices. The mating connector is Crestron part number JDSM31F-1, 31 pin, female, SMT connector. Refer to the following table for pin assignments of the module interface connector.
Two-Way RF Transceiver Module Crestron MNET-CWD1012 Antenna This SMA non-standard male antenna port is located at edge of the circuit board for attaching the included dipole antenna. APPROVED ANTENNAS: The MNET-CWD1012 antenna interface has a unique coupling designed to ensure that no antenna other than the one supplied shall be used with the device. Replacement antennas may be purchased from Crestron according to the following description: Part Number: ANXX2400R00MHZ-2 Description: ANTENNA, 2400.
Crestron MNET-CWD1012 Two-Way RF Transceiver Module minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions: 1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna.
Two-Way RF Transceiver Module Crestron MNET-CWD1012 Mounting The module has four 0.215” diameter holes for screws that can be used to secure the module to an enclosure or other printed circuit board (PCB). This module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: EROCWD1012 .
Crestron MNET-CWD1012 Two-Way RF Transceiver Module This page intentionally left blank Hardware Guide - DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Hardware Guide - DOC. 6351 02.05 INTERNAL USE ONLY Specifications subject to change without notice.
