Ovens Humidity with Microprocessor Controls 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Rev.
Ovens Humidity with Microprocessor Controls 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Rev.
5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Ovens Humidity with Microprocessor Controls Rev. 8 (1/05) FL-2267 Page 3 of 13 INSTALLATION INSTRUCTIONS VENTING YOUR OVEN: 1. The purpose of ventilating hoods is to direct and capture smoke, grease-laden vapors, heat, odors, or fumes. 2.
Ovens Humidity with Microprocessor Controls 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Rev. 8 (1/05) FL-2267 Page 4 of 13 OPERATING INSTRUCTIONS Figure 1: Control Panel HOW TO START UNIT: (for first-time operation only) A new oven needs to “burn off” factory oils and glue before it’s first use. Do NOT load food into oven until this has been done! 1. Push power switch to “ON”. 2. Press the SELECT button; choose the TIMED mode.
925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Ovens Humidity with Microprocessor Controls Rev. 8 (1/05) FL-2267 Page 5 of 13 OPERATING INSTRUCTIONS, continued: HOW TO SET THE CONTROL, continued FOR PROBE COOK OPERATION: Press the SELECT button to choose the probe mode. PROBE TEMPERATURE: 1. Press the PROBE/TIME button. The display will show the probe setpoint temperature. 2. Use the UP and DOWN arrows to set the desired temperature.
Ovens Humidity with Microprocessor Controls 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Rev. 8 (1/05) FL-2267 Page 6 of 13 OPERATING INSTRUCTIONS, continued HOW TO OPERATE WITH HUMIDITY: HOW TO OPERATE WITH FOOD, continued HOW TO SET HOLD-ONLY MODE: 1. Push power switch to “ON”. 2. Press the STOP button and oven will switch to HOLD cycle. 3. Press the HOLD button and set the desired hold temperature.
Ovens Humidity with Microprocessor Controls 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Rev. 8 (1/05) FL-2267 Page 7 of 13 MAINTENANCE INSTRUCTIONS HOW TO CLEAN THE UNIT: MAINTENANCE: WATER PAN Drain, wipe and fill water pan daily. (Clear vinyl drain-hose is provided). 1. Push hose onto drain nozzle under the base. 2. Turn knob to open the drain. To fully Dry Out: 1. Drain until 1/8” of water is left in pan bottom. 2.
5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Ovens Humidity with Microprocessor Controls Rev. 8 (1/05) FL-2267 Page 8 of 13 MAINTENANCE INSTRUCTIONS TROUBLE-SHOOTING GUIDE If unit gets too hot or won’t shut off, disconnect power at branch panel. DO NOT UNPLUG CORD! If hot unit is NOT working, first check the following causes: 1. Cord is unplugged from wall outlet. 3. Switch is turned off. 2.
Ovens Humidity with Microprocessor Controls 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Rev. 8 (1/05) FL-2267 Page 9 of 13 MAINTENANCE INSTRUCTIONS TROUBLE-SHOOTING GUIDE, continued HOW TO ADJUST THE DOOR LATCH: 1. For vertical (up and down movement) adjustment: a. Loosen (2) screws located in magnetic strike. b. Move strike up or down for alignment to magnet on latch. c. Tighten screws to secure 2.
Ovens Humidity with Microprocessor Controls 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Rev. 8 (1/05) FL-2267 Page 10 of 13 REPLACEMENT PARTS: Include all information on nameplate when ordering parts. Figure 2: Control Panel Hot Unit Replacement Parts ITEM DESCRIPTION CMP Part No. ITEM DESCRIPTION 1. Switch (On/Off) 2. Microprocessor Control 3. Vent Fan 4. Fan Guard 5. Fuse Fuse Holder 6. Blower Kit 7. Contactor 8.
5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Ovens Humidity with Microprocessor Controls Rev. 8 (1/05) FL-2267 Page 11 REPLACEMENT PARTS For “PASS-THRU” OVENS CO or RO151FPWUA SERIES: Include all information on nameplate when ordering parts.
5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Ovens Humidity with Microprocessor Controls FL-2267 Page 12 Rev. 8 (1/05) of 13 REPLACEMENT PARTS For OVENS CO or RO151FPWUA SERIES: Include all information on nameplate when ordering parts.
5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • www.crescor.com Ovens Humidity with Microprocessor Controls Rev.