KLMKBM-01 Bluetooth module instructions Ble mesh
Version update instructions No. Date Content Version 1 2021-05-08 New document V1.0.
Catalogue 1 Product description................................................................................................................. 4 2 Performance characteristics ................................................................................................. 4 2.1 main feature................................................................................................................... 4 3 Module interface...................................................................................
1 Product description The Bluetooth module uses Telink’s TLSR8258 Bluetooth chip, which is a Bluetooth mesh ad hoc network module specially designed based on BLE V5.0 protocol ，it supports the Sig Mesh V1.0 standard. Customers only need to connect the module to the application product and turn on the power to link with mobile phone equipment, digital product equipment and PDA equipment to realize remote control of the mesh network.
Figure 3.1 Schematic diagram of KLMKBM-01 Bluetooth module 3.2 Pin definition The interface pin definition is shown in Table 3.2： Table 3.2 KLMKBM-01 Bluetooth module interface pinout description IO No. Symbol 1 RST I/O Hardware reset pin (active low), corresponding to RESETB of IC.
GPIO port, can be used as LED drive PWM output, default corresponding to red light GPIO port, can be used as LED driver PWM output, default corresponding to cold white light 13 R I/O 14 CW I/O 15 RX I/O Serial port receiving pin UART RX 16 TX I/O Serial port sending pin UART TX Note: P stands for power supply pin, I/O stands for input and output pin, AI stands for analog input. If you have your own requirements for the light color controlled by the PWM output, please contact us.
4.3 Power consumption in working mode Table 4.3 Power consumption during TX continuous transmission Symbol Condition Typical Unit Itx Continuous transmission, 10.5dBm output power 23 mA Irx Continuous reception 6.3 mA IDC In Mesh network working state 7 mA 1.2 uA 0.4 uA Deep sleep mode (reserved 16KBRAM) Deep sleep mode (no RAM reserved) Ideepsleep1 Ideepsleep2 5 RF parameters 5.1 Basic RF characteristics Table 5.1 Basic RF characteristics Parameter Description Working frequency 2.
Table 5.3 RX sensitivity Parameter RX sensitivity Frequency offset error Min Typical Max 1Mbps - -94.5 - 2Mbps - -91 - 1Mbps -250 - +300 2Mbps -300 - +200 - - -10 - Co-channel interference suppression Unit dBm KHz dB 6 Module basic instructions KLMKBM-01 module recommends that users can access the network through the APP-"zhihui connect" developed by our company configuration. Two bulbs are needed for control, and our module needs to be soldered to the corresponding lamp board.
6.2 Group control Enter the created group to control the devices assigned to the group at the same time. 6.3 Single light control After the added device enters the device control page, you can perform other operation controls such as switching/dimming of a single light. 6.4 Other settings Timing/countdown can be set, device OTA and bulb can be deleted from the network.
Appendix statement Federal Communications Commission (FCC) Declaration of Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Federal Communication Commission Statement (FCC, U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15 Subpart C 15.247 & 15.207 & 15.209 2.3 Specific operational use conditions The module is a Bluetooth module with BLE 2.4G function. Operation Frequency: 2402~2480MHz Number of Channel: 40 Modulation: GFSK Type: PCB Antenna Gain: 2 dBi The module can be used for mobile or applications with a maximum 2dBi antenna.
2.9 Information on test modes and additional testing requirements Operation Frequency: 2402~2480MHz Number of Channel: 40 Modulation: GFSK Host manufacturer must perfom test of radiated & conducted emission and spurious emission, etc according to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product.
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Labels Host Device must contain the following label on the outside of the unit: Contains FCC ID：2AZTV-KLMKBM-01 Installation Guidance The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.
