User's Manual

ManualsBrandsCree ManualsElectronicsRFM MODULE

1 of 4 LPN00212X0003A7

CS Series With Cree SmartCast™ Technology

CS14™, CS18™ LED Linear Luminaire

8' and 4' Luminaires

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

• The CS Series LED linear luminaire is for

suspended, with cable or threaded rod, or

surface mount applications using appropriate

tong hangers. Reference individual mounting

accessory installation instructions for speciﬁc

mounting types.

• Designed for use in 120–277V, 50-60 Hertz

protected circuit (fuse box, circuit breaker) and

supply wire shall be rated minimum 12AWG,

600V, 90 C rated).

TO INSTALL:

NOTE: When removing luminaire from packaging, keeping

protective plastic wrap on ﬁxture during installation and

construction.

FOR PLASTIC TONG HANGERS (TM):

NOTE: Center hole can accommodate 1/2" diameter rod

maximum.

STEP 1:

Remove cross brace and securely insert it into the “+” shaped

openings in the plastic tong hanger. See Figures 1 & 2. For single

units or end row ﬁxtures, place the plastic tong hanger assembly

into center spine no more than 18" from each end of ﬁxture and

twist approximately 45 degrees until the plastic tong hanger

assembly is securely in place and approximately 90 degrees to

the length of ﬁxture. See Figure 3.

STEP 2:

For continuous row installation, continue with next ﬁxture using

a minimum of one tong hanger per unit. Each bracket should be

properly snug and be difﬁcult to slide along the back spine.

Cross Brace

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant

l’installation.

2. This luminaire must be installed in accordance with the NEC or your

local electrical code. If you are not familiar with these codes and

requirements, consult a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code

électrique local. Si vous n’êtes pas familier avec ces codes et ces

exigences, veuillez contacter un électricien qualié.

3. Check to make sure that all the xture connections have been properly

made and the xture is grounded to avoid potential electrical shocks.

4. Do not handle energized module with wet hands or when standing on

wet or damp surfaces, or in water.

5. Suitable for damp locations.

Convient aux emplacements humides.

SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE

WARNING - Maximum connected load with a single power supply shall

not exceed maximum ampacity rating of #12 AWG THHN through-wire

conductors. Use only lighting controls with relay or FET-based outputs,

or lighting controls with neutral connection. Reference www.cree.com/

lighting for recommended dimming control options. Avoid handling

LEDs directly. Not intended for use in environments containing airborne

corrosive agents such as chemical solvents, cleaners, or cutting uids

Summary of content (4 pages)

PAGE 1
CS Series With Cree SmartCast™ Technology CS14™, CS18™ LED Linear Luminaire 8' and 4' Luminaires INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER- Risk of shock- Disconnect power before installation. DANGER – Risque de choc – Couper l’alimentation avant l’installation.
PAGE 2
FOR OPTIONAL METAL TONG HANGERS (TMM): 3 NOTE: Center hole can accommodate 3/8" diameter rod maximum. Recommended for surface mount installations. 18" 18" 4 STEP 1: For single units or end row fixtures, place metal tong hanger bracket over center spine no more than 18" from each end of fixture. See Figure 3. Insert supplied bolt through the metal tong hanger and secure with lock washer and nut, tightening to secure spine to the metal tong hanger. See Figure 4 & 5.
PAGE 3
ELECTRICAL CONNECTIONS FOR CONNECTING MULTIPLE LUMINAIRES TOGETHER: 8 STEP 1: Attach two fixtures together with screws & nuts provided. See Figure 8. STEP 2: Remove endcap cover of first fixture to reveal through-wiring plug. Open swing door of connecting fixture and remove knockout and extend wiring in preparation for connections. See Figure 9. STEP 3: Carefully feed AC and dimming plugs into wiring compartment through knockout opening.
PAGE 4
12 RF Module Access Hole, Reset Button Inside Blue LED Placement RESET RF MODULE NOTE: The Blue LED is located behind the CREE logo on the RF Module. The CREE logo with illuminate blue when the Blue LED is active. STEP 1: Actuate RESET button through the access hole. Push and hold until LED on RF Module begins blinking rapidly (approximately 6-7 seconds). See Figure 12. STEP 2: Release for 1 sec. STEP 3: Press/Hold RESET button for 0.5 sec.