Mayfield Cottage Assembly Instruction Model: 9200 WARNING: CHOKING HAZARD Creative Cedar Designs www.creativecedardesigns.com Customer Service: Please log onto our website and fill out a request for missing / damaged parts. email: custservice@creativecedardesigns.com phone: 1-888-363-4967 Revision Date: 12/03/2019 Unassembled parts may be a choking hazard to children 3 years and younger. The plastic bags that contain the hardware may present a choking hazard to small children.
Creative Cedar Designs CreativeCedarDesigns.com Table of Contents Letter to Customer Positioning Your Playcenter Tools Required for Assembly Helpful Installation Hints Operating Instructions Maintenance Instructions Disposal Instructions CPSC Information Sheet Assembly Instructions Limited Warranty Warranty Claim Procedure 2 3 3 4 5 6 6 7 9 41 42 Your owner’s manual should be read carefully before starting assembly.
STOP…PLEASE READ!! IF YOU HAVE ANY QUESTION OR ARE MISSING A PART, PLEASE DO NOT CONTACT THE RETAILER THAT YOU PURCHASED THIS PRODUCT FROM. PLEASE VISIT www.creativecedardesigns.com OR CONTACT US DIRECTLY AT OUR OFFICE, 1-888-363-4967 WE WILL ANSWER YOUR QUESTIONS, OR HELP WITH WHAT YOU NEED. For more efficient service, please log onto our website at www.creativecedardesigns.com and fill out a request for missing or damaged parts. A completed product registration is also necessary for all warranty claims.
Dear Customer: Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable fun. Creative Cedar Designs equipment is recommended for use by children 3 to 10 years of age. Creative Cedar Designs structures are not intended for public use. Creative Cedar Designs does not warranty any of its residential structures subjected to commercial use.
The instructions and owner’s manual for your new Playcenter should be read in its entirety before assembly, to minimize problems and safety issues. We recommend reading the owner’s manual thoroughly after you have identified all of the parts for your Playcenter as discussed in the Helpful Installations Hints section below. Positioning Your Play center 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper.
Helpful Installation Hints 1. Depending on your experience, assembly of this Play set should take approximately 3 to 4 hours after inventory of parts. Therefore, we recommend you set aside a full day for assembly. 2. Identify all of the parts for your Playcenter. Empty each box and lay out boards so you can see each part.. We suggest laying out the boards in the same order as found on the parts identification page. This will assist when completing the assembly steps.
READ! VERY IMPORTANT! If you are missing parts or have questions regarding the installation of our quality product PLEASE email or contact us directly. Our trained staff will be happy to assist you. Please do not return the product to the retail store. Customer service hours: Monday thru Friday 9am to 5pm Saturday 9am to 2pm (During Season) Eastern Standard Time. E-mail: custservice@creativecedardesigns.com Ph:1-888-363-4967 Operating Instructions: NOTE: Your children’s safety is our #1 concern.
Maintenance Instructions: 1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But not so tight that you crack the wood) It is particularly important that this procedure be followed at the beginning of each season. 2. Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sanding may be necessary to maintain a safe playing environment.
APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material Also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS11 X3.1 The U.S.
Customer Notes
Basic Setup Dimensions Place the set on level ground, not less than 6ft (2M) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical wires.
Parts Identification 2A027 BACK GABLE (1 REQ.) 2A022 FRONT GABLE (1 REQ.) 2A021 RIGHT FRONT WALL (1 REQ.) 2A023 DOOR (1 REQ.) 2A028 LEFT WALL (1 REQ.) 2A026 BACK WALL (1 REQ.) 2A025 PORCH ROOF (Rt.) (1 REQ.) 2A024 PORCH ROOF (Lt.) (1 REQ.) 2A029 RIGHT WALL (1 REQ.) 2A033 DORMER FRONT (1 REQ.) 2A032 FLOOR SQUARE (16 REQ.) 2A030 SMALL ROOF SECTION (1 REQ.) 2A034 WINDOW SILL (1 REQ.) 2A031 LARGE ROOF SECTION (1 REQ.) 1-5/32 [29mm] 19 [483mm] 1 1/8 [29mm] LJ104 UPRIGHT (RT) (2 REQ.
11 15/16 [304mm] 5/8 [16mm] 7 1/16 [180mm] 11/16 [17mm] 1 3/16 [30mm] 5/8 [16mm] LS40 WALL SLAT (1 REQ.) 9 1/4 [235mm] 4-7/8 [124mm] 1 [25mm] LH112 PLANTER BRD. (4 REQ.) 3 1/8 [79mm] 3 1/8 [79mm] 6 1/8 [155mm] 1 [25mm] 7/16 [11mm] 5 19/32 [141mm] LH109 PLANTER BRD. (2 REQ.) LS100 DORMER ROOF BRD. (1 REQ.) 44 3/4 [1137mm] LS102 DORMER ROOF BRD. (1 REQ.) 1 [25mm] LK77 SHELF GUSSET (3 REQ.
11/16 [17mm] LS52 DOOR STOP (1 REQ.) 2 11/16 [68mm] 11/16 [17mm] 2 11/16 [68mm] (M002) GREEN L-BRACKET (SMALL) (13 REQ.) LT61 ROOF TRIM (2 REQ.) 11/16 [17mm] 47 1/2 [1207mm] LT70 CORNER UPRIGHT (1 REQ.) (PHN867) PLASTIC PHONE (1 REQ.) 3 3/8 [86mm] LT36 BOTTOM WALL RAIL (1 REQ.) 19 [483mm] 11/16 [17mm] LT49 BRACE (8 REQ.) 11/16 [17mm] 43 3/4 [1111mm] LT62 ROOF TRIM (2 REQ.) 35 3/16 [894mm] 11/16 [17mm] LT71 BOTTOM WALL RAIL (2 REQ.) (93BHNG) DOOR HINGE w/ HDW (2 REQ.
Hardware Identification FW1/4 Flat Washer 1/4-20 x 2-1/2” Socket Head Bolt (30) (9) FW1/4 Fender Washer (53) 1/4-20 x 2-1/4” Socket Head Bolt (18) Imperial 1/4-20 T-Nut LW1/4 Lock Washer 1/4-20 x 1-3/4” Socket Head Bolt (10) (57) (28) 0 1/4" 1/2" 1/4-20 x 1-5/8” Socket Head Bolt 3/4" (5) 1" (4) WS1/8 X 3/4’’ Wood Screw (14) 2" (74) (6) (1) 25 30 3" (150) 80 90 WS1/8 X 1 3/8" Wood Screw (56) 4" 100 110 WS1/8 X 1 5/8" Wood Screw (53) 120 WS1/8 X 2" Wood Screw 5" (64) 13
Measuring hardware It is very important that you get the right hardware in the correct place when assembling the unit. You can use the ruler below to measure your hardware or you can compare the hardware to the hardware identification page. 5" 4" 3" 2" 1" 14 140 130 120 110 100 90 80 70 60 50 40 20 30 25 3/4" 1/2" 15 1/4" 10 0 5mm 0 NOTES: 1) Do not include bolt head when measuring length of bolt. 2) Include full length of deck screw when measuring.
Phase 1 Sub-Floor Assembly Phase Hardware 1/4-20 x 1-3/4” Socket Head Bolt FW1/4 Flat Washer LW1/4 Lock Washer (10) (10) WS1/8 X 3/4’’ Wood Screw (10) (14) Phase Parts LN18 SUB-FLOOR SLAT (3 REQ.) LN21 SUB-FLOOR SLAT (3 REQ.) LP24 SUB-FLOOR SLAT (1 REQ.) LN22 SUB-FLOOR SLAT (1 REQ.) LN19 SUB-FLOOR SLAT (1 REQ.) LN23 SUB-FLOOR SLAT (1 REQ.) LN20 SUB-FLOOR SLAT (1 REQ.) LP25 SUB-FLOOR SLAT (1 REQ.) LP27 SUB-FLOOR SLAT (1 REQ.) LP26 SUB-FLOOR SLAT (1 REQ.
Phase Floor Square Att. 2 Phase Hardware WS1/8 x 2-1/8” Wood Screw (80) WS1/8 x 1-5/8” Wood Screw (48) Phase Parts STEP 1 LN113 SUB-FLOOR SLAT (6 REQ.) 2A032 FLOOR SQUARE (16 REQ.) LN114 SUB-FLOOR SLAT (6 REQ.
Phase 3 Phase Hardware Right Wall Prep. 1/4-20 x 2-1/4" Socket Head Bolt (4) 1/4" Lock Washer (4) 1/4" Fender Washer WS1/8 X 1 1/8" Wood Screw (4) (10) 1/4-20 T-Nut (4) Phase Parts NOTE: MAKE SURE UPRIGHTS ARE ORIENTED CORRECTLY. T-NUTS ARE INSERTED TOWARD THE INSIDE OF THE UNIT LJ104 UPRIGHT (RT) (2 REQ.) STEP 1: LT71 BOTTOM WALL RAIL (1 REQ.) 2A029 RIGHT WALL (1 REQ.
Phase 4 Phase Hardware Left Wall Prep. 1/4-20 x 2-1/4” Socket Head Bolt (4) 1/4” Fender Washer 1/4" Lock Washer (4) WS1/8 X 1 1/8" Wood Screw (4) (4) (12) 1/4-20 T-Nut Phase Parts NOTE: MAKE SURE UPRIGHTS ARE ORIENTED CORRECTLY. T-NUTS ARE INSERTED TOWARD THE INSIDE OF THE UNIT LJ105 UPRIGHT (LT) (2 REQ.) LT71 BOTTOM WALL RAIL (1 REQ.) 2A028 LEFT WALL (1 REQ.
Phase 5 Left Wall Assembly Phase Hardware 1/4-20 x 2-1/4” Socket Head Bolt (6) 1/4" Fender Washer (6) 1/4" Lock Washer (6) Phase Parts LT48 CORNER UPRIGHT (1 REQ.) LT70 CORNER UPRIGHT (1 REQ.
Phase 6 Front & Back Wall Attachment Phase Hardware 1/4-20 x 2-1/4” Socket Head Bolt (4) 1/4" Fender Washer 1/4" Lock Washer (4) (4) WS1/8 X 1 1/8" Wood Screw (4) Phase Parts LT36 BOTTOM WALL RAIL (1 REQ.) 1/4-20 x 2 1/4 Socket Head Bolt LOCK WASHER & FENDER WASHER 2A021 2A029 RIGHT WALL (1 REQ.) 2A021 RIGHT FRONT WALL (1 REQ.) 2A026 BACK WALL (1 REQ.
Phase 7 Left Wall Attachment Phase Hardware WS1/8 X 1 5/8" Wood Screw FRONT WALL NOT SHOWN FOR CLARITY Phase Parts WS1/8 X 1 1/8" Wood Screw (4) (5) RIGHT WALL STEP 1 BACK WALL LT63 BOTTOM WALL RAIL (1 REQ.
Phase Front & Back Wall 8 Slat Attechment Phase Hardware 1/4-20 x 1 Socket Head Bolt (1) WS1/8 X 1" Wood Screw (10) 1/4 Lock Washer (1) 1/4 Fender Washer (1) Phase Parts LS65 WALL SLAT (1 REQ.) LS40 WALL SLAT (1 REQ.) LS66 WALL SLAT (1 REQ.) LS41 WALL SLAT (1 REQ.
Phase 9 Front & Back Gable Attachment Phase Hardware 1/4-20 x 2-1/2” Socket Head Bolt (4) 1/4" Fender Washer 1/4" Lock Washer (4) (4) WS1/8 X 1" Wood Screw (10) Phase Parts 2A022 FRONT GABLE (1 REQ.) 2A027 BACK GABLE (1 REQ.
Phase 10 Shelf Assembly Phase Hardware WS1/8 X 2" Wood Screw (50) Phase Parts 6 5/8 [168mm] 6 5/8 [168mm] LS76 SHELF BOARD (1 REQ.) 1 [25mm] LK77 SHELF GUSSET (3 REQ.) LH109 PLANTER BRD. (2 REQ.) 2A034 WINDOW SILL (1 REQ.) LS75 SHELF BOARD (1 REQ.) LH112 PLANTER BRD. (4 REQ.) LH111 PLANTER BRD. (2 REQ.) LH110 PLANTER BRD. (2 REQ.
Phase 11 Shelf Attachment Phase Hardware WS1/8 X 2" Wood Screw (14) Phase Parts SHELF ASSEMBLIES FROM PREVIOUS PHASE CENTER SHELF AND FLUSH WITH WINDOW EDGE. ATTACH TO WALL WITH (6) WOOD SCREWS THROUGH PRE-DRILLED HOLES ON THE INSIDE OF THE WALL AND INTO THE GUSSETS.
Phase 12 Brace Attachment Phase Hardware WS1/8 X 1" Wood Screw (32) Phase Parts TYPICAL INSIDE VIEW / LAYOUT FOR RIGHT & LEFT WALLS OTHER PARTS NOT SHOWN FOR CLARITY LT49 BRACE (8 REQ.
Phase 13 Fence Assembly Phase Hardware 1/4-20 x 2-1/2” Socket Head Bolt (5) LW1/4 Lock Washer (10) 1/4-20 x 1-5/8” Socket Head Bolt FW1/4 Flat Washer (10) (5) Phase Parts LT28 FENCE PICKET (9 REQ.) 1/4-20 x 2 1/2” SOCKET HEAD BOLT 1/4" LOCK WASHER & 1/4" FLAT WASHER LT30 FENCE PICKET (1 REQ.
Phase 14 Place Cottage On Floor PLACE THE FLOOR ASSEMBLY IN THE SAFE AREA YOU HAVE CHOSEN (MAKE SURE THE AREA IS LEVEL). NOTE THE ORIENTATION OF THE COTTAGE DOOR IN RELATIONSHIP TO THE FLOOR ASSEMBLY WITH FENCE UPRIGHTS ATTACHED, AS SHOWN BELOW. DO NOT USE THE SHELVES TO LIFT THE COTTAGE ONTO THE FLOOR. THIS MAY DAMAGE THE SHELVES! PLACE THE COTTAGE TOWARDS THE CENTER OF THE FLOOR FOR NOW (TEMPORARY). THIS WILL ALLOW ROOM TO WORK AROUND THE COTTAGE AS WE PROCEED WITH THE FENCE ASSEMBLY.
Phase 15 Fence Rail Assembly Phase Hardware 1/4-20 x 1-1/4” Socket Head Bolt (4) LW1/4 Lock Washer (4) WS1/8 X 2 1/8" Wood Screw FW1/4 Flat Washer (4) (4) Phase Parts LT31 FENCE RAIL (2 REQ.) LT32 FENCE RAIL (2 REQ.) LT34 FENCE RAIL (2 REQ.) LT33 FENCE RAIL (2 REQ.
Phase 16 Fence Rail Attachment Phase Hardware 1/4-20 x 1-1/8" Socket Head Bolt (2) LW1/4 Lock Washer (2) FW1/4 Flat Washer 1/4-20 T-Nut (2) WS1/8 X 1 1/8" Wood Screw (2) (30) COTTAGE NOT SHOWN FOR CLARITY LT32 LT30 1/4-20 T-NUT 1/4-20 x 1 1/8" SOCKET HEAD BOLT 1/4" LOCK WASHER & 1/4" FLAT WASHER LT33 LT31 LT32 SUGGEST THE USE OF A CLAMP 17-3/8" 6-1/2" 90° 90° 90° 17-3/8" 90° 90° 6-1/2" LT30 LT33 TIP: START BY BOLTING RAIL ASSEMBLIES TO LT30.
Phase 17 Attach Cottage to Fence Phase Hardware 1/4-20 x 1-1/8 Socket Head Bolt (4) LW1/4 Lock Washer (4) Phase Parts WS1/8 X 1 1/8" Wood Screw (12) FW1/4 Flat Washer (4) LT35 FENCE RAIL (2 REQ.) CAREFULLY POSITION / ALIGN COTTAGE WITH HOLES IN REAR FENCE RAILS 'LT31' THEN ATTACH 'LT35' AS SHOWN BELOW.
Phase 18 L-Bracket Attachment Phase Hardware FW1/4 Fender Washer #14 x 3/4” Screw STUDY PLAN VIEW BELOW FOR BRACKET LOCATIONS (26) (26) Phase Parts (M002) GREEN L-BRACKET (SMALL) (13 REQ.
Phase 19 Fence Picket Attachment Phase Hardware WS1/8 X 1 1/8" Wood Screw (88) SIDE 4 SIDE 1 Phase Parts WS1/8 X 1 1/8" Wood Screw LT29 FENCE PICKET (22 REQ.
Phase 20 Roof Attachment Phase Hardware WS1/8 X 1 3/8" Wood Screw (28) FLOOR & FENCE NOT SHOWN FOR CLARITY Phase Parts LT61 ROOF TRIM (2 REQ.) LT62 ROOF TRIM (2 REQ.) 2A030 SMALL ROOF SECTION (1 REQ.) PEEK DETAIL 2A031 LARGE ROOF SECTION (1 REQ.
Phase 21 Dormer Assembly Phase Hardware WS1/8 X 1 3/8" Wood Screw (26) WS1/8 X 1" Wood Screw (2) Phase Parts LR96 DORMER GABLE (1 REQ.) LR97 DORMER BRACE (1 REQ.) LR92 DORMER WALL (LT) (1 REQ.) LS98 DORMER BRACE (1 REQ.) LR93 DORMER WALL (RT) (1 REQ.) LS99 DORMER ROOF BRD. (1 REQ.) LS102 DORMER ROOF BRD. (1 REQ.) LS101 DORMER ROOF BRD. (1 REQ.) LS100 DORMER ROOF BRD. (1 REQ.) 2A033 DORMER FRONT (1 REQ.
Phase 22 Accessory Attachment Phase Hardware WS1/8 X 1" Wood Screw WS1/8 X 5/8" Wood Screw (6) (20) FLOOR & FENCE NOT SHOWN FOR CLARITY #14 x 3/4” Screw LT49-1 WINDOW SUPPORT. (1 REQ.) (1) Phase Parts LT49-1 6’’ (PF2990) WINDOW FRAME (2 REQ.) INSERT CENTER SUPPORT FOR WINDOW FRAMES. (PHN867) PLASTIC PHONE (1 REQ.) (4) WS 1/8 X 1" Wood Screw POSITION DORMER OVER PRE-DRILLED HOLES ON ROOF.
Phase 23 Porch Roof & Door Stop Phase Hardware 1/4-20 x 1-1/2” Socket Head Bolt ROOF & FENCE NOT SHOWN FOR CLARITY (4) 1/4” Flat Washer (4) Phase Parts 1/4” Lock Washer (4) 1/4-20 T-Nut WS1/8 X 1 1/8" Wood Screw (4) (4) 2A024 2A025 2A024 PORCH ROOF (Lt.) (1 REQ.) 2A025 PORCH ROOF (Rt.) (1 REQ.) LS52 DOOR STOP (1 REQ.
Phase 24 Phase Hardware Porch Roof WS1/8 X 1 3/8" Wood Screw WS1/8 X 2 1/8" Wood Screw ROOF, FLOOR & FENCE NOT SHOWN FOR CLARITY (2) (6) WS1/8 X 1" Wood Screw (14) Phase Parts LQ58 SMALL GABLE (1 REQ.) LQ57 LQ57 SOFFIT BOARD (1 REQ.
Phase 25 Door & Placard Attachment Phase Parts CreativeCedarDesigns.com ID-TAG w/ HARDWARE (1) REQ. 2A023 DOOR (1 REQ.) DOOR HINGE (93BHNG) w/ HARDWARE (2) REQ. DOOR KNOB (DRKNOB) w/ HARDWARE (1) REQ. 5 3/16" DRILL BIT 8 1 DOOR KNOB 3/16 x 1” SCREW LOCK WASHER & FLAT WASHER ATTACH ID-TAG CENTERED BELOW WINDOWS. 3 CreativeCedarDesigns.com 19 3/8" 1/2" 3 3 1/2" DOOR ATTACHMENT: POSITION DOOR AND HINGES USING DIMENSIONS SHOWN. ATTACH HINGES WITH (6) WS#8 X 3/4" Wood Screws EACH.
Phase 26 Anchoring Phase Parts ASSEMBLY COMPLETE! MAKE SURE TO TIGHTEN ALL HARDWARE (BP001-B) ANCHOR PACK w/ HDW (2 REQ.) NOTE: DO NOT OVER TIGHTEN HARDWARE. STAKE STAKE TO AVOID SPLITTING WOOD, PRE-DRILL ALL STAKE HARDWARE.
LIMITED WARRANTY Creative Cedar Design offers many fun, interactive, and safe play centers. We only guarantee the original purchaser that this product is free of defects in materials for 30 days from the date of purchase, with the product registration card and the dated receipt as proof of purchase. Under this warranty there will be a replacement for the defective component of the play center. All parts are covered by a one year warranty.
Warranty claim procedure If you are confident that your play system has been installed and maintained properly, and you have a warranty claim, proceed with the following steps: 1. We will need copy of your proof of purchase (Vendor sales receipt only.) 2. We require a brief written description of the warranty issue. 3. Photos of warranted parts and of the entire play system. If any of the above steps are not completed, there may be delays in the completion of your claim, or possibly warranty cancellation.
