OPERATOR’S MANUAL | MANUAL DEL OPERADOR 4-CYCLE GAS TRIMMER DESBROZADORA DE GAS DE 4 TIEMPOS WS405 CMXGTAMD30SA IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US. SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS. 1-888-331-4569 769-22690 / 00 WWW.CRAFTSMAN.
TABLE OF CONTENTS All information, illustrations, and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. The product may vary slightly from the illustrations contained in this manual. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• IMPORTANT SAFETY INSTRUCTIONS • READ ALL INSTRUCTIONS BEFORE OPERATING SAFETY WARNINGS FOR GAS UNITS WARNING: WARNING: When using the unit, all safety instructions must be followed. Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders. Please keep these instructions for later use. • • • • • • • • • • • • • Gasoline is highly flammable and its vapors can explode if ignited.
• • • • • • • • • OTHER SAFETY WARNINGS Do not force the unit. It will do a better, safer job when used at the intended rate. Always turn the unit off when operation is delayed or when carrying the unit from one location to another. Make sure all moving parts come to a complete stop. Before setting the unit down, always make sure the engine is off and all moving parts have stopped. If the unit strikes or becomes entangled with a foreign object, stop the unit immediately. Check for damage.
• SAFETY & INTERNATIONAL SYMBOLS • This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING SYMBOL • SAFETY ALERT SYMBOL MEANING • ON/OFF STOP CONTROL Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.
KNOW YOUR UNIT APPLICATIONS Muffler As a trimmer: • Cutting grass and light weeds • Edging • Decorative trimming around trees, fences, etc. Other optional attachments may be used with this unit.
ASSEMBLY INSTALLING THE CUTTING HEAD SHIELD Mount Bracket Hole WARNING: To prevent serious personal injury, never operate the unit without the cutting head shield in place. Tab Bolt 1. Remove the wing nut and washer from the cutting head shield. 2. Insert the short tab (the one without a hole) on the mount bracket into the slot on the cutting head shield (Fig. 1). 3. Rotate the cutting head shield until the bolt on the cutting head shield protrudes through the hole on the mount bracket (Fig. 1). 4.
Removing the Attachment 1. 2. 3. 4. Primary Hole Set the unit on a flat, level surface. Turn the knob counterclockwise to loosen the coupler (Fig. 3). Press and hold the release button (Fig. 5). Pull the attachment straight out of the coupler (Fig. 4). Release Button Guide Recess Fig. 5 INSTALLING AND ADJUSTING THE HANDLE Handle Installing the Handle 1. Push the handle down onto the upper shaft housing (Fig. 6). Make sure the bolt hole faces to the right (Fig. 6). 2.
Clip Buckle Shoulder Strap / Harness Loop Strap Fig. 8 Fig. 9 OIL AND FUEL USING THE RIGHT OIL Use a high-quality SAE 30 weight oil. DO NOT use dirty oil. Failure to use clean oil of the correct type can cause premature engine wear and failure. ADDING OIL: INITIAL USE Oil Fill Plug WARNING: OVERFILLING THE CRANKCASE MAY CAUSE SERIOUS PERSONAL INJURY. NOTE: This unit was shipped without oil in the crankcase. Oil must be added before starting the unit. NOTE: Never add oil to the fuel tank.
USING THE RIGHT FUEL The use of old fuel is the most common cause of performance problems. Use only fresh, clean unleaded gasoline. NOTE: This unit has a four-cycle engine. DO NOT mix oil with gasoline. Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1% water in the fuel can make fuel and oil separate, forming acids when stored. ALWAYS use fresh fuel (less than 30 days old).
STARTING AND STOPPING WARNING: Operate this unit only in a well-ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. On/Off Switch (I = On / O = Off) WARNING: Avoid accidentally starting the unit. To avoid serious injury, the operator and the unit must be in a stable position when pulling the starter rope (Fig. 13). Throttle Lockout Throttle Control Fig.
OPERATION HOLDING THE UNIT WARNING: Always wear eye, hearing, hand, foot and body protection to reduce the risk of injury when operating this unit. WARNING: To prevent serious personal injury, avoid arm contact with the engine while operating the unit. The engine may be extremely hot. • • • • • • Stand in the operating position (Fig. 14). Stand up straight. Do not bend over. Keep feet apart and firmly planted. Hold the shaft grip with the right hand. Keep the right arm slightly bent.
DECORATIVE TRIMMING When trimming around trees, posts, fences, etc., rotate the whole unit so that the cutting head is at a 30° angle to the ground (Fig. 16). Fig. 16 EDGING The trimmer attachment can be used for edging (Fig. 17). Alternatively, a bladed lawn edger attachment can also be purchased for use with this unit. Rotating the Trimmer Attachment WARNING: To avoid serious personal injury and damage to the unit, shut the unit off before rotating the attachment.
MAINTENANCE MAINTENANCE SCHEDULE WARNING: To avoid serious personal injury, always stop the engine and allow it to cool before cleaning or maintaining the unit. Never perform cleaning or maintenance while the unit is running. Disconnect the spark plug wire to prevent the unit from starting accidentally. Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up.
Removing Old Trimming Line and Obstructions Bump Knob 1. When the trimming line runs out, the last piece should automatically eject from the cutting head. If it does not, push the bump knob down and pull the remaining line out of the cutting head. 2. If the line will not come out or the cutting head is otherwise obstructed: a. Firmly press a tab on the cutting head with your thumb (Fig. 22). DO NOT press the tab with a screwdriver or other object. b. Continue pressing the tab.
CHECKING THE OIL LEVEL WARNING: Check the oil level before each use. The importance of maintaining the proper oil level cannot be overemphasized. 1. Stop the engine and allow it to cool. 2. Set the unit on a flat, level surface, such as a workbench or table. The cutting head shield should hang over the edge so that the engine is level (Fig. 24). NOTE: Failure to keep the engine level may result in oil overfill. 3. Clean the area around the oil fill plug (Fig.
MAINTAINING THE AIR FILTER Slots Air Filter Cover Failure to maintain the air filter can result in poor performance or can cause permanent damage to the engine. Engine failure due to improper air filter maintenance is not covered by the product warranty. Cleaning the Air Filter Tabs Air Filter 1. Open the air filter cover: press in the lock tab and swing the air filter cover up (Fig. 28). 2. Remove the air filter from the air filter housing (Fig. 28). 3. Wash the air filter in detergent and water.
CLEANING AND STORAGE CLEANING STORAGE • WARNING: To avoid serious personal injury, always stop the engine and allow it to cool before cleaning or maintaining the unit. • • • • • Use a small brush to clean the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic. Wipe off any moisture with a soft cloth. Never store a fueled unit where fumes may reach an open flame or spark.
TROUBLESHOOTING PROBLEM SOLUTION THE ENGINE WILL NOT START The fuel tank is empty Fill the fuel tank with fresh fuel The primer bulb was not pressed enough Press the primer bulb 10 times The fuel is old (over 30 days) Drain the fuel tank and add fresh fuel The spark plug is fouled Replace the spark plug THE ENGINE WILL NOT IDLE The air filter is dirty Clean or replace the air filter The fuel is old (over 30 days) Drain the fuel tank and add fresh fuel The idle speed is incorrect Adjust the id
WARRANTY MTD LLC LIMITED WARRANTY FOR CRAFTSMAN® BRANDED HANDHELD PRODUCT Limited Warranty The limited warranty set forth herein is given by MTD LLC to the Initial Purchaser (as defined herein) with respect to new Craftsman branded hand held product (“Product”). This limited warranty does not cover Emission Control Systems and is not a Federal Emission Control Warranty Statement as defined by U.S. federal law.
This Warranty Does Not Cover And MTD LLC Disclaims Any Responsibility For: 1. 2. 3. 4. Loss of time or loss of use of the Product. Transportation costs and other expenses incurred in connection with the transport of the Product to and from the authorized service provider. Any loss or damage to other equipment or personal items. Damage resulting from the installation or use of any accessory or non-OEM (original equipment manufacturer) part for use with the Product. Limitations: 1.
NOTES 22
TABLA DE CONTENIDO Toda la información, las ilustraciones y las especificaciones contenidas en este manual se basan en la información más reciente disponible en el momento de impresión del manual. Nos reservamos el derecho de hacer cambios en cualquier momento sin aviso previo. El producto puede variar ligeramente de las ilustraciones contenidas en este manual. Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Conozca su unidad . . . . . . . . . . . . . . .
• INSTRUCCIONES DE SEGURIDAD IMPORTANTES • LEA TODAS LAS INSTRUCCIONES ANTES DE USAR LA UNIDAD ADVERTENCIAS DE SEGURIDAD PARA LAS UNIDADES A GASOLINA ADVERTENCIA: La gasolina es sumamente inflamable y sus vapores pueden explotar si se Se deben respetar ADVERTENCIA: todas las instrucciones de seguridad al usar la unidad. Por encienden. Adopte las siguientes precauciones: favor, lea estas instrucciones antes de utilizar la unidad para garantizar la seguridad del operador y los observadores.
• • • • • • • • • • • • • • OTRAS ADVERTENCIAS DE SEGURIDAD Sostenga siempre la unidad con ambas manos durante la operación. Sostenga firmemente ambas manijas o empuñaduras. No se extienda demasiado. Siempre debe estar bien afirmado y mantener el equilibrio adecuado. Tenga cuidado al trabajar sobre escalinatas, cuestas empinadas o pendientes. Para evitar lesiones graves, no haga funcionar la unidad desde una escalera de mano o un techo.
• SÍMBOLOS INTERNACIONALES Y DE SEGURIDAD • Este manual del operador describe símbolos de seguridad e internacionales, así como pictogramas, que pueden aparecer en este producto. Lea el manual del operador para obtener información completa sobre seguridad, montaje, funcionamiento, mantenimiento y reparaciones. SÍMBOLO SIGNIFICADO SÍMBOLO • SÍMBOLO DE ALERTA DE SEGURIDAD SIGNIFICADO • APAGADO/ENCENDIDO DE CONTROL DE PARADA Indica peligro, advertencia o precaución.
CONOZCA SU UNIDAD APLICACIONES Como desbrozadora: • Corta hierbas y malezas ligeras • Bordeado • Recorte decorativo alrededor de árboles, vallas, etc. Con esta unidad se pueden usar otros dispositivos de sujeción opcionales.
ENSAMBLAJE INSTALACIÓN DEL PROTECTOR DEL CABEZAL DE CORTE Soporte de montaje Orificio ADVERTENCIA: A fin de evitar que se produzcan Lengüeta lesiones personales graves, no opere nunca la unidad sin el protector del cabezal de corte en su lugar. Perno 1. Extraiga la tuerca de mariposa y la arandela del protector del cabezal de corte. 2. Inserte la lengüeta corta (la que no tiene orificio) en el soporte de montaje dentro de la ranura del protector del cabezal de corte (Fig. 1). 3.
ADVERTENCIA: Este botón de liberación debe colocarse a presión solamente en el orificio principal a menos que se especifique lo contrario. Si se utiliza un orificio equivocado, se podrían producir lesiones personales o daños a la unidad. Orificio principal Botón de liberación Extracción del accesorio 1. Coloque la unidad en una superficie plana y nivelada. 2. Gire la perilla en el sentido contrario a las agujas del reloj para aflojar el acoplador (Fig. 3). 3.
Sujetador Correa de hombro / Presilla de enganche del arnés Hebilla Correa Fig. 8 Fig. 9 ACEITE Y COMBUSTIBLE USO DEL ACEITE CORRECTO Use un aceite pesado de alta calidad SAE 30. NO utilice aceite sucio. Si no se utiliza aceite limpio del tipo adecuado se puede producir un desgaste y una falla prematura del motor. INCORPORACIÓN DE ACEITE: USO INICIAL Tapón para llenado de aceite ADVERTENCIA: SI SE LLENA EXCESIVAMENTE EL CÁRTER SE PUEDEN PRODUCIR LESIONES PERSONALES GRAVES.
USO DEL COMBUSTIBLE CORRECTO CARGA DE COMBUSTIBLE EN LA UNIDAD El uso de combustible viejo es la causa más frecuente de los problemas de rendimiento. Sólo se debe utilizar gasolina nueva, limpia y sin plomo. NOTA: Esta unidad tiene un motor de cuatro tiempos. NO mezcle el aceite con la gasolina. ADVERTENCIA: La gasolina es extremadamente inflamable. Los vapores encendidos pueden explotar. Detenga siempre el motor y déjelo enfriar antes de llenar el depósito de combustible.
ARRANQUE Y PARADA ADVERTENCIA: Opere esta unidad únicamente en una zona bien ventilada, al aire libre. Los humos de escape de monóxido de carbono pueden ser mortales en un lugar cerrado. Interruptor encendido / apagado (I = Encendido / O = Apagado) ADVERTENCIA: Se debe evitar arrancar accidentalmente la unidad. A fin de evitar que se produzcan lesiones graves, el operador y la unidad deben estar en una posición estable cuando se jala la cuerda de arranque (Fig. 13).
FUNCIONAMIENTO CÓMO SOSTENER LA UNIDAD ADVERTENCIA: Utilice siempre protección ocular, auditiva, de manos, pies y corporal para reducir el riesgo de sufrir lesiones durante la operación de esta unidad. ADVERTENCIA: A fin de evitar lesiones personales graves, evite el contacto del brazo con el motor mientras opere la unidad. El motor puede estar muy caliente. • • • • • • Párese en la posición de arranque (Fig. 14). Párese derecho. No se incline sobre el aparato.
RECORTE DECORATIVO Cuando recorte alrededor de árboles, postes, vallas, etc., rote toda la unidad de manera que el cabezal de corte quede en un ángulo de 30° en relación con el suelo (Fig. 16). Fig. 16 BORDEADO El accesorio de la recortadora puede ser utilizado para el bordeado (Fig. 17). De manera alternativa, también se pueden comprar un accesorio de bordeadora de césped con cuchillas para utilizar con esta unidad.
MANTENIMIENTO PLAN DE MANTENIMIENTO ADVERTENCIA: A fin de evitar lesiones personales graves, siempre pare el motor y deje que se enfríe antes de limpiar o mantener la unidad. No realice ninguna tarea de limpieza o mantenimiento mientras la unidad esté en funcionamiento. Desconecte el cable de la bujía para evitar que la unidad arranque accidentalmente. Lleve a cabo los procedimientos necesarios de mantenimiento con la frecuencia indicada en la tabla.
NOTA: NO oprima la perilla de impacto mientras se enrolla el hilo. La perilla de corte gira para un solo lado, dependiendo del modelo de la unidad. NOTA: Si queda muy poco hilo sobresaliendo, se podría retraer dentro del cabezal de corte. Perilla de impacto Extracción de hilo de recorte viejo y obstrucciones 1. Cuando el hilo de corte se acaba, el último trozo es expulsado automáticamente del cabezal de corte.
CONTROL DEL NIVEL DE ACEITE ADVERTENCIA: Controle el nivel de aceite antes de cada uso. No está de más insistir en la importancia de mantener el nivel de aceite adecuado. 1. Detenga el motor y deje que se enfríe. 2. Ubique la unidad sobre una superficie plana y nivelada, como un banco de trabajo o una mesa. El protector del cabezal de corte debe quedar colgando del borde de manera que el motor quede nivelado (Fig. 24). NOTA: Si no se mantiene el nivel del motor puede resultar en exceso de aceite. 3.
MANTENIMIENTO DEL FILTRO DE AIRE Tapa del filtro de aire Si no se mantiene el filtro de aire se puede obtener un rendimiento insuficiente o se pude dañar el motor de manera permanente. Las averías del motor ocasionadas por un mantenimiento inadecuado del filtro de aire no están cubiertas por la garantía del producto. Limpieza del filtro de aire Ranuras Lengüetas Filtro de aire 1.
MANTENIMIENTO DE LA BUJÍA 1. Detenga el motor y deje que se enfríe. Sujete con firmeza la funda de la bujía y tire para sacarla de la bujía. 2. Limpie alrededor de la bujía. Retire la bujía de la tapa del cilindro con una llave de cubo de 5/8 pulgadas, girando en sentido contrario a las agujas del reloj. ADVERTENCIA: No limpie de forma abrasiva ni raspe o limpie los electrodos de las bujías. La presencia de polvo abrasivo en el motor podría dañar el cilindro. 0.025 pulgadas (0.635 mm) 3.
LIMPIEZA Y ALMACENAMIENTO LIMPIEZA ALMACENAMIENTO • ADVERTENCIA: A fin de evitar lesiones personales graves, siempre pare el motor y deje que se enfríe antes de limpiar o mantener la unidad. • • Use un cepillo pequeño para limpiar el exterior de la unidad. No utilice detergentes fuertes. Los productos de limpieza para el hogar que contienen aceites aromáticos como pino y limón, y los disolventes como el queroseno, pueden dañar el plástico. Limpie todo rastro de humedad con una tela suave.
SOLUCIÓN DE PROBLEMAS PROBLEMA SOLUCIÓN EL MOTOR NO ARRANCA El depósito de combustible está vacío Llene el depósito de combustible con combustible nuevo El bulbo del cebador no se presionó lo suficiente Oprima el bulbo del cebador 10 veces El combustible está viejo (más de 30 días) Drene el depósito de combustible y agregue combustible nuevo La bujía está averiada Vuelva a colocar la bujía EL MOTOR NO FUNCIONA AL RALENTÍ El filtro de aire está sucio Limpie o reemplace el filtro de aire El combus
GARANTÍA MTD LLC GARANTÍA LIMITADA PARA EL PRODUCTO DE MANO DE MARCA CRAFTSMAN® Garantía Limitada La garantía limitada establecida en este documento es otorgada por MTD LLC al Comprador Inicial (como se define aquí) con respecto al nuevo producto manual de marca Craftsman ("Producto"). La presente garantía limitada no cubre los Sistemas de control de emisiones y no constituye una Declaración de garantía del control de las emisiones federal según lo definido por las leyes federales de los Estados Unidos.
Lo que NO Cubre esta Garantía Limitada Esta Garantía Limitada No Cubre lo Siguiente (las “Exclusiones”): 1. 2. 3. 4. Los productos adquiridos fuera de los Estados Unidos. Los daños producidos por la falta de mantenimiento y/o un mantenimiento inadecuado, según se describe en el manual del operador. El desgaste normal resultante de usar el Producto.
NOTAS 44
NOTAS 45
NOTAS 46
NOTAS 47
TO ORDER REPLACEMENT PARTS OR SCHEDULE REPAIR SERVICE PARA ORDENAR PIEZAS O PEDIR SERVICIO DE REPARACIÓN 1-888-331-4569 CRAFTSMAN® IS A REGISTERED TRADEMARK OF STANLEY BLACK & DECKER, INC., USED UNDER LICENSE. ES UNA MARCA REGISTRADA DE STANLEY BLACK & DECKER, INC., UTILIZADA BAJO LICENCIA. © 2019 CRAFTSMAN PRODUCT MANUFACTURED BY: / PRODUCTO FABRICADO POR: MTD LLC P.O. Box 361131 Cleveland, OH 44136-0019 U.S. & CANADA ONLY • SÓLO EN EE.UU.