Owner's Manual Nlodei No. 875.198650 1/2-in. Composite impact Wrench Unpacking When unpacking during transit, product into this Make product, sure any carefully loose inspect fittings, for any bolts, etc, damage that may are tightened before have occurred putting this service, WARNING: Please read and save these safety and operating instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Owner's Manual Model No. 875.198650 Owner's Manual Model No. 875.
Owner's Manual Disconnect Model No. 875.198650 the air tool from air supply Use attachments and during non-operation, Do not wear loose fitting air powered clothing, tool. designed for use with Always examine scarves, or neck ties in work area, Loose accessories before mounting cracks, or signs of damage.
Owner's Manual Model No. 875.198650 Owner's Manual be a flexible Air Tool Hook Up movement Model No. 875.198650 hose in order to isolate of the compressor, This tool features a power regulator valve Route the initial take-off as straight up the shop wall and as high as possible, minimize line (pipe) This will help water leaving the compressor and traveling (fig.
Owner's Manual Model No. 875.198650 Owner's Manual Model No. 875.198650 Lubrication An in-line filter-regulator-lubricator (fig 1) is recommended as it increases tool life and keeps the tool in sustained operation. The in-line lubricator should be regularly checked and filled with air tool oil. Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to the tools exhaust ports and holding the throttle open approximately 30 seconds.
Owner's Tool runs slow or will not operate. Manual Model 1. Grit or gum in tool No. 875.198650 1. Flush the tool with air tool oil, gum solvent, or an equal mixture of SAE 10 motor oil and kerosene. Lubricate the tool Owner's Manual 2. Lubricate the tool according to the lubrication instructions in this manual 3. Low air pressure 3a. Adjust the regulator on the tool to the maximum setting (If applicable). 3b. Adjust the compressor regulator to tool maximum while the tool is running free. 4.
IPROFESSIONAL Llave de impacto I compuesta de 112 pulg Desempaquetar Despues de desempaquetar el examinelo cuidadosamente par_ dafios que pudieron durante el transporte. apretar cualquier haber ocurr Cerci6res accesorio, antes de poner este producto per er ADVERTENCIA: Lea y guarde estas instrucciones de seguridad y operaci6n.
Manual dei Hropietarlo Modeio No. 75. 19 6bU Manual dei Hropietarlo Modeio No. 75. 1 90 PSIG M,&XIMO Caracteristicas y operaci6n Especificaciones Garantia del producto Requisitos del compresor Instrucciones de seguridad importantes Instalaci6n y operaci6n Mantenimiento Piano de vista despiezada y lista de piezas Localizaci6n y soluci6n de fallas Craftsman Modelo 875,198650 1/2-in. Ilave inglesa compuesta de impacto representa un golpear duro, dise_o gemelo de martillo que produce 725 Ibs.
Manual del Propietario Modelo Desconecte Ja herramienta del suministro de aJre antes de cambiar herramientas o accesorios, darle servicio o durante el tiempo que no est6 funcionando. No use ropa suelta, bufandas o corbatas en el _rea de trabajo. La ropa suelta podria quedar atrapada en las piezas en movimiento y resultar en una lesi6n personal grave. No use joyas mientras usa la herramienta. Las joyas podrian quedar atrapadas en las piezas en movimiento y resultar en una lesi6n personal grave.
Manual del Propietario Conexidn Modelo de la manguera No. 875.198650 • de aire Linea principal = Dia, int, min, 1/2 pulg Inclinado hacia abajo y alejandose Linea Dia, Lubricador Regulador bifurcaci6n int, 1 = Linea de admisi6n Filtro Manguera de aislamiento de drenaje Compresor Figura 1 Cone×i6n de la rnanguera de aire Mangueras de aire para sus herramientas neum_ticas La Figura 1 ilustra la conexi6n recomendada de una manguera de aire.
Manual del Propietario Modelo No. 875.198650 Manual del Propietario Modelo No. 875.198650 Piano de vista Lubricaci6n Se recomienda lubricador usar un filtro-regulador- en linea (Fig.1) ya que incrementa la duraci6n de la herramienta y mantiene la herramienta en una operaci6n sostenida. Debera comprobar el lubricador en linea con regularidad y Ilenarlo con aceite para herramientas de aire comprimido.
Manual del Propietario La herramienta funciona lentamente o no funciona. 1. En la herramienta hay polvo, arena o resina. 2. En la herramienta no Modelo No. 875.198650 1. Irrigue la herramienta con aceite para herramientas neum_ticas, diluyente de resinas, o una mezcla de igual proproci6n de aceite de motor SAE 10 y queroseno. Lubrique la herramienta despues de la limpieza. hay aceite. 2. Lubrique la herramienta de acuerdo a las instrucciones de lubricaci6n indicadas en este manual. 3.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800-469=4663) Call anytime, day or night (U.S.A. and Canada) www.sears.com www.sears.