@ Owner's lVlanuai Model No. 875.168820 1/2 in. impact Wrench Unpacking When unpacking inspect for any damage occurred loose before this during fittings, putting transit. bolts, product, that carefully may have Make sure any etc. are tightened this product into service. WARNING: Please read and save these safety and operating instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Owner's Manual Model No. 875.168820 Owner's Manual Model No. 875.168820 90 PSI Maximum This toot is designed to operate at an air Features & Benefits Specifications Product Warranty Compressor Requirements Important Safety Instructions Installation and Operation Maintenance Exploded View Drawing & Parts List Troubleshooting ONE YEAR FULL WARRANTY ON CRAFTSMAN TOOL gauge pressure (90 PSI) maximum, at the instructions and warnings before tool.
Owner's IV nua! Disconnect IVbde! No. 875 bhe air tool from air supply Do not wear loose fit'dng clobhing, scapJes, or neck ties in work area. Loose cloming may become caught in moving parts and resultin serious personal injury. Do not wearjewelry when operal_ng any tool. Jewelry may become caught in moving parts and resultin serious personal injury.
Owner's Manual IVbde! No. 875 168820 Owner's Manual IVbde! No. 875 1688 be a flexible hose in order to isolate Air Tool Hook Up movement of _e compressor. Route _e inilJal take4Dffline (pipe) as slzaight up _e shop wall and as high as possible. This will help minimize water leaving _e compressor and lzaveling _rough system Slope _e main lines down at least 3/4 inch per lOfeet of pipe away from air compressor; _is will draw • e condensate wi_ _e flowofair and away from _e compressor.
Owner's Manua! IVbde! No. 875 16B820 Owner's Manua! IVbde! No. 875 16B82D 4S 1. Disconnectlhe the air supply. impactwrench 2 Remove the slot_d L ubrication from 42 screwor 41 Allen ,445 head screw from lhe oil porLhole An inqine filter-regulatorqubricator (fig 1) is recommended as it increases tool life and keeps the tool in sustained operation. The inqine lubricator should be regularly checked and filled with air tool oil.
Owner's Tool runs slow or will not operate. Manua! 1. Gritor IVbde! No. 875 16E 2D gum in tool 1. Flush the tool with air tool oil, gum solvent, oran equal mixture of SAE 10 motor oil and kerosene. Lubricate the tool after cleaning 2 No oil in tool 2 Lubricate the tool according to the lubrication ins_uctlons in this manual 3 Low air pressure 3a. Adjust the regulator on the tool to the maximum setting (If applicable). go.
CRA ° Manual del P ropietario IViodelo No. 875.1 68820 L lave de impacto de 1/2 pulg D esempaquetar Despues de desempaqueta rel producto, examinelo cuidadosament_ para idenlJficar dahos que pudieron haberocurrido durant_ el transports. CerciOrese de apretarcualquieraccesorio, pemo, etc., ant_s de poner est_ producto en servicio. ADVERTENCIA: Lea y guarde estas instrucciones de seguridad y operacion. Lea detalladamente antes de tratar de ensamblar, instalar, operar o mantener el producto descrito.
Manual del Propietario Model No. 875.168820 Manual del Propietario Model No. 875.168820 90 PSIG M,_XIMO _, Caracteristicas yoperaci6n Especificaciones _, Garantiadel producto Requisitos del compresor _, Instrucciones de seguridad importantes Instatacidn y operaci6n _, Mantenimiento _, Piano de vista despiezada y lista de piezas _, Locatizaci6n y soluci6n de fatlas La Itave de impacto de mando cuadrado de 1/2 pulg Craftsman, Modelo 875.
Manual del Propietario Descor_ectelaherranienta del suministrode airean1_sde cambia r herramient_so accesorios, dade seFvicio 0 duranteel"dempoque no est_funcionando. No use ropa suelta,bufandaso corbalms en elareade Imabajo. La ropasuellmpodria quedar aITapadaen laspiezasen movimientDy resullmr en una lesion personalgrave. No usejoyas mientras usa la herramienta. Lasjoyas podrian quedar atrapadas en las piezas en movimientuy resullnren una lesion personal grave.
IVhnual del Propietario Conexion IVbdei No. 875 de ia manguera Linea principal = Dia, int. rain. Inclinado hacia abajo y Linea bifurcacion Dia. 2 = Linea int. 1/2 pulg Dia. Lubricador Regulador • de aire 1/2 pulg bifurcacion 1 = Linea de admision Filb_o Incline hacia abajo las Iineas principales por Io menos 3/4 de pulg por cada lOpies de tdberia alejandose del compresor de aire.
Manual del Propietario IVbdel No. 875 16B820 Manual del Propietario IVbdel No. 6"75 168820 43 1. L ubricaciOn Se recomienda usarun flltro-reguladorlubdcadoren Iinea (Fig. 1)ya que incrementa la duration de la herramienta y manlJene la herramienta en una operacion sost_nida. Debera comprobarel lubdcadoren Iinea con reguladdad y Ilenado con aceit_ para herramientas de aire compdmido.
IVbnual de! Propietario La herramienla funciona lenlnmenl_ o no funciona. 1. En la herramienla hay polvo, arena o resina. IVbdel No. 875 168820 1. Irrigue la herramien_a con aceit_ para herramien_as neuma_Jcas, diluyen'e de resinas, o una mezcla de igual proproci0n de acei_ de motur SAE 1Oyqueroseno, Lubrique la herramien_a despues de la limpieza. 2 En la herramien_a no hay acei_, 2 Lubrique la herramien_a de acuerdo alas ins_FdCCiones de lubricaci0n indicadas en est_ ma nua I.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it7 For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800-469=4663) Call anytime, day or night (U.S.A. and Canada) www,sears.